As you may have guessed from the title, I have a problem with a drive that says it has 22 currently unreadable sectors. It was a new drive when I installed it a couple of years ago and it has been running fine since. The unreadable sectors finally worried me enough to make a decent effort to...

Hardware/OS: WD 2TB - Western Digital Black - /dev/ada0 (additional drive we installed for zpool) WD 2TB - Western Digital Black - /dev/ada2 (additional drive we installed for zpool) 1TB - Seagate Barracuda 3.5 - /dev/ada1 (standard drive that comes in the Dell T310s we use) 8GB RAM Intel(R)...

Hello I am doing smartctl -a on my drive and getting the following results. The weird thing is one partition I have does not mount but the other one mounts fine. That makes me wonder whether there is a data corruption issue on just one partition or whether infact the whole drive is broken...

Heyas there, 4 days ago I received an e-mail from my NAS, that it detected a smart error. It's on a RED drive and the reading is follows: === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: WD-WCC4N0ELX1P2 LU WWN Device Id...

I'm trying to use that amazing fan controller script by Stux here. It works great by itself, but I thought that it would be nice to put it into a jail, just in case. The thing is: smartctl is unable to access /dev/ada* disks from the jail. Right now I ended with a custom devfs ruleset, but...

Well, I have a dilemma. Recently I had a big problem with my WD60EFRX disks (WD Red-6TB).. I had a 9 disk array and replaced about 7 of them due to failures.. I tested every replacement with badblocks before confirming as safe.. Last two disks arrived from WDC Support ( which I had to send...

This post https://forums.freenas.org/index.php?threads/where-does-the-system-log-of-services-s-m-a-r-t-information-go.63205/ prompted me to have a peek in the log just for interest and I found: (recent example for /dev/da4) Apr 18 14:52:47 freenas smartd[3480]: Device: /dev/da3 [SAT], SMART...

I updated, all was fine, then I read a post somewhere about SMART not being necessary to be turned on for the boot device (SD card/USB mirror), so I went to Storage>View Disks, clicked the boot device opened the window and unticked SMART, clicked ok, then I get some log message like...

I've tried to solve this via Google but not had any luck. The baseboard is Supermicro X10 Xeon and the SAS drives are connected via two LSI 9211 HBAs. When I run `smartctl -a /dev/XXX`, I get detailed attribute data for SATA HDDs only. I know that SCSI/SAS, and therefore smartctl, didn't...

Over the last week or so, 3 of my old 4TBs all started throwing errors in the messages log. The pool is fine - there's plenty of redundancy and I swapped them over in good time - so now the 3 of them are sitting on the side, waiting for me to figure if they're worth a hit with...

Hi All, Wondering if someone can take a look at my smartctl out put below, Just had an email saying the error count has increased on my drive, not sure if its failing etc. Have ran the disk through Hard Disk Sentinel and that shows that the drive is perfect 100 health Thanks Steve...

freenas got very upset about one of my disks, a 6TB WD Red drive. I replaced the disk and made it happy once again. now I am trying to understand the SMART results. it starts with overall-health assessment passed but also says pre-fail a bunch of places. i have attached the report the disk is...

Hello! I have Freenas 9.10-U4 and some raid 0 virtual disks, that smartctl can detect correctly as /dev/passX. Can i configure smartd manually by the way, that will saved after updates or upgrades? Now [root@storsrv] ~# cat /usr/local/etc/smartd.conf...

I have six disk system, with two each of 2TB, 3TB and 4TB drives. Freenas is complaining of bad sectors. Should I replace the drive? I have another 4TB drive to put in it but then the mirror "balance' is out. Also, all the drive replacement docs I found seem to be for a degraded pool, which...

Hey everyone! I'm running FreeNAS 9.10.2-U4 and my setup includes 3 4TB WD Red Edition (NAS version @5400rpm). Today I got the following email and a critical error: CRITICAL: Aug. 1, 2017, 8:09 p.m. - Device: /dev/ada1, Self-Test Log error count increased from 0 to 1 It seems that one of the...

Not sure where the best place to post this is as this is my first post. I cannot get the smart service to start. I have tried enabling it from the gui and shell with no joy. I fould that smart does not seem to be enabled for drive da0. I tried starting it vi shell with this command smartctl...

Hello everyone, This week I received a critical alert because of an "unrecoverable error in one or more devices": http://illumos.org/msg/ZFS-8000-9P After a scrub, ada1 showed 11 checksum errors so I ran a long SMART test. These are the results: # smartctl -a /dev/ada1 smartctl 6.5...

Preface.... This may be a dumb question.... Ok, I have used 9.2.1.5, 9.2.1.8, 9.3, and am now running the most current version of 9.10.1-U4. My hardware is beyond recommended specs. I have looked for a few days now for this exact question and cant seem to find a specific answer (again, maybe...

Hi all, I'm sure some of you can help me out. I have a 3 TB (WD30EFRX) drive which has an error in FreeNAS (v.9.10). The error is "Device: /dev/ada0, 1 Currently unreadable (pending) sectors". I did the smartctl long test and the result is PASSED and no errors detected. Also I did the long WD...