martin_nv
Cadet
- Joined
- Dec 26, 2013
- Messages
- 4
Freenas newbie here. I switched out an old SMC network adapter that was only 100Mb and installed an Intel PRO 1000, and it does not seem to get an IP address and connect to the network. On the bootup, the text scrolling by says this:
The output from ifconfig in the shell is as follows:
To test the NIC I then boot with FreeBSD liveCD, the Intel nic works (ping test ok) BUT only after configuring the IP address manually using this command:
ifconfig em0 inet 10.10.10.90 netmask 255.255.255.0
BUT If I try to issue this command in Freenas I still cannot ping.
If I boot the same box with a Mint Linux liveCD, the Intel adapter gets an IP address and works fine.
The version is FreeNAS-9.2.1.8-RELEASE-x64 ( have downloaded the latest.
The DHCP server on my network is working, other devices get IP addresses no problem.
The UPC on the NIC is 735858202176, googling this UPC shows the network adapter I have.
Any help on what I should try next to get this going would be appreciated!
TIA,
Martin
Code:
Setting hostname: freenas.local. Starting dhclient. em0: no link ..... got link em0: link state changed to UP DHCPDISCOVER on em0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on em0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on em0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on em0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on em0 to 255.255.255.255 port 67 interval 17 No DHCPOFFERS received No working leases in persistent database - sleeping.
The output from ifconfig in the shell is as follows:
Code:
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=4219b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TS04,WOL_MAGIC,VLAN_HWTSO> ether 68:05:ca:3a:bd:32 inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255 nd6 options=9<PERFORMNUD,IFDISABLED> media: Ethernet autoselect (1000baseT <full-duplex>) status: active ipfw0: flags=8801<UP,SIMPLEX,MULTICAST> metric 0 mtu 65536 nd6 options=9<PERFORMNUD,IFDISABLED> lo0 flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet 127.0.0.1 netmask 0xff000000 nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> [root@freenas] ~#
To test the NIC I then boot with FreeBSD liveCD, the Intel nic works (ping test ok) BUT only after configuring the IP address manually using this command:
ifconfig em0 inet 10.10.10.90 netmask 255.255.255.0
BUT If I try to issue this command in Freenas I still cannot ping.
If I boot the same box with a Mint Linux liveCD, the Intel adapter gets an IP address and works fine.
The version is FreeNAS-9.2.1.8-RELEASE-x64 ( have downloaded the latest.
The DHCP server on my network is working, other devices get IP addresses no problem.
The UPC on the NIC is 735858202176, googling this UPC shows the network adapter I have.
Any help on what I should try next to get this going would be appreciated!
TIA,
Martin