[Message Erreur]Cam status: ATA status Error

Bidule0hm · Feb 15, 2015

T'as juste recopié ce qu'il y avait dans le post plus haut ?

De toute façon faut attendre que les tests se terminent avant de refaire les smartctl -a, y'en a pour plusieurs heures, c'est pour ça que je te les ai fait lancer avant de te coucher, demain matin on est sûr qu'ils seront terminés. Je viens de penser, tant que tu y es tu devrais aussi lancer le test sur ada3 et 4 --> smartctl -t long /dev/adaX avec X = 3 et 4

nydjo · Feb 15, 2015

Non j ai pas recopier ! j' ai recommencer il me semblais bien qu il testait un truc !

apres recherche je suis certain d'avoir raidz1 ou raidz2

j ai 10 To physique (5*2) et il me semble qu apres formatage il me restait que 6 to il faut que je retrouve l article qui en parle mais la j'y arrive pas mais je pencherais pour le z2

Bidule0hm · Feb 15, 2015

S'il te restait 6 To alors tu as logiquement du RAID-Z2 ;) ou alors une autre config bizarre mais ce n'est pas le cas à priori.

Par contre il faut vraiment que tu arrêtes d'éditer (surtout sans le marquer) pour rajouter des trucs STP. L'edit c'est juste pour éviter les double-posts, mais si j'ai posté tu peux poster à la suite plutôt que d'éditer le post d'avant ;) Je dis ça parce que j'ai complètement raté ça "il y as aussi des messages sur ada4" dans ce post et c'est plutôt important; qu'est-ce qu'il raconte sur ada4 ?

nydjo · Feb 15, 2015

ok comment je peux faire tout les test en une fois

Bidule0hm · Feb 15, 2015

Tu les as déjà lancé sur ada0, ada1 et ada2 en même temps :D t'as juste à faire smartctl -t long /dev/adaX avec X = 3 et 4 pour les 2 disques restants et t'auras un test de lancé sur chaque disque en même temps. T'as plus qu'à laisser tourner cette nuit et on verra le résultat demain ;)

nydjo · Feb 15, 2015

ok merci !
tu es un chef !

Bidule0hm · Feb 15, 2015

De rien ;)

Attends d'avoir la solution au problème avant de me remercier, ce n'est pas sûr que j'arrive à comprendre ce qu'il se passe :p

nydjo · Feb 15, 2015

Je te remercie pour le temps que tu prends pour moi !!!

Sinon j'ai aucune idée de comment je vais pouvoir envoyé le rapport.

J'ai ceci sur mon écran freenas
Dev/ ada2 /8 currently unread
Dev/ada2/8 Offline uncorrect

Dev/ada4 / 1 currently unread

A tout hasard pour le ssh:
Je vais installer putty et essayer de le configurer pour mon nas

Bidule0hm · Feb 16, 2015

Pour pouvoir scroller dans le résultat d'une commande rajoute | less après la commande. Tu pourras utiliser les flèches haut/bas pour scroller et la touche q pour quitter ce mode.

Donc il me faudrait les résultats de cat /var/log/messages | tail -n 200 ainsi que de smartctl -a /dev/adaX (avec X de 0 à 4) chacun dans un bloc code séparé stp. Prends ton temps et fais les choses correctement ;)

A noter qu'à priori t'as ada2 ET ada4 qui sont en train de te dire adieu (ça n'a toutefois pas l'air critique vu qu'il n'y a pas beaucoup de secteurs illisibles mais en général ça commence comme ça et peu de temps après t'es à plusieurs milliers de secteurs illisibles et là c'est cuit)... J'espère que c'est bien du RAID-Z2 et pas du RAID-Z1 car sinon les chances de pouvoir remonter la pool seront extrêmement minces.

nydjo · Feb 16, 2015

Je rentre chez moi vers 19h et je m attaque a ça vers 21h !!!

Mais ma femme va me tuer si je perds toutes les photos des petits !!!

en espérant qu on y arrive

Bidule0hm · Feb 16, 2015

Ok ;)

Et les backups ? On ne le répètera jamais assez mais un RAID ne remplace pas des backups.

nydjo · Feb 16, 2015

J'ai réussi a installer putty !

je vais tout refaire au propre.

Pour la petite histoire
j'ai pas énormement perdu mais une heure avant la panne j'ai vidé son appareil photo avec 1 année dedans…

camcontrol devlist

Code:

[root@freenas] ~# [root@freenas] ~#  camcontrol devlist
[root@freenas]: No match.
[root@freenas] ~# <ST32000542AS CC34>                at scbus0 target 0 lun 0 (pass0,ada0)
Badly placed ()'s.
[root@freenas] ~# <ST32000542AS CC34>                at scbus1 target 0 lun 0 (pass1,ada1)
Badly placed ()'s.
[root@freenas] ~# <ST2000DL001-9VT156 CC41>          at scbus2 target 0 lun 0 (pass2,ada2)
Badly placed ()'s.
[root@freenas] ~# <SAMSUNG HD204UI 1AQ10001>         at scbus3 target 0 lun 0 (pass3,ada3)
Badly placed ()'s.
<WDC WD20EADS-00S2B0 01.00A01>     at scbus4 target 0 lun 0 (pass4,ada4)
[root@freenas] ~# <WDC WD20EADS-00S2B0 01.00A01>     at scbus4 target 0 lun 0 (pass4,ada4)
Badly placed ()'s.
[root@freenas] ~# < Patriot Memory PMAP>             at scbus6 target 0 lun 0 (pass5,da0)
Badly placed ()'s.
[root@freenas] ~# [root@freenas] ~# <ST32000542AS CC34>                at scbus0 target 0 lun 0 (pass0,ada0)
Badly placed ()'s.
[root@freenas] ~# Badly placed ()'s.
Unmatched '.
[root@freenas] ~# [root@freenas] ~# <ST32000542AS CC34>                at scbus1 target 0 lun 0 (pass1,ada1)
Badly placed ()'s.
[root@freenas] ~# [root@freenas] ~# <ST2000DL001-9VT156 CC41>          at scbus2 target 0 lun 0 (pass2,ada2)
Badly placed ()'s.
Unmatched '.
[root@freenas] ~# [root@freenas] ~# <ST2000DL001-9VT156 CC41>          at scbus2 target 0 lun 0 (pass2,ada2)
Badly placed ()'s.
[root@freenas] ~# Badly placed ()'s.
Unmatched '.
[root@freenas] ~# [root@freenas] ~# <SAMSUNG HD204UI 1AQ10001>         at scbus3 target 0 lun 0 (pass3,ada3)
<SAMSUNG HD204UI 1AQ10001>         at scbus3 target 0 lun 0 (pass3,ada3)
Badly placed ()'s.
[root@freenas] ~# [root@freenas] ~# <SAMSUNG HD204UI 1AQ10001>         at scbus3 target 0 lun 0 (pass3,ada3)
Badly placed ()'s.
[root@freenas] ~# Badly placed ()'s.
Unmatched '.
[root@freenas] ~# [root@freenas] ~# <WDC WD20EADS-00S2B0 01.00A01>     at scbus4 target 0 lun 0 (pass4,ada4)
Badly placed ()'s.
[root@freenas] ~# Badly placed ()'s.
Unmatched '.
[root@freenas] ~# < Patriot Memory PMAP>             at scbus6 target 0 lun 0 (pass5,da0)
Badly placed ()'s.
[root@freenas] ~# < Patriot Memory PMAP>             at scbus6 target 0 lun 0 (pass5,da0)
[root@freenas] ~# [root@freenas] ~# < Patriot Memory PMAP>             at scbus6 target 0 lun 0 (pass5,da0)
Badly placed ()'s.
Badly placed ()'s.
[root@freenas] ~# Badly placed ()'s.
Unmatched '.
[root@freenas] ~#  camcontrol devlist
[root@freenas] ~# [root@freenas] ~#  camcontrol devlist
[root@freenas]: No match.
[root@freenas] ~# <ST32000542AS CC34>                at scbus0 t

zpool status -v

Code:

[root@freenas] ~# zpool status -v
no pools available

DMESG

Code:

[root@freenas] ~# dmesg
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
aesni0: No AESNI support.
padlock0: No ACE support.
acpi0: <ALASKA A M I> on motherboard
ACPI Error: [RAMB] Namespace lookup failure, AE_NOT_FOUND (20110527/psargs-392)
ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region) (20110527/nsinit-380)
acpi0: Power Button (fixed)
acpi0: reservation of 67, 1 (4) failed
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
Event timer "HPET5" frequency 14318180 Hz quality 440
Event timer "HPET6" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
pci0: <multimedia, HDA> at device 3.0 (no driver attached)
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7d0c000-0xf7d0c3ff irq 20 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf7c00000-0xf7c00fff,0xf0000000-0xf0003fff irq 18 at device 0.0 on pci3
re0: Using 1 MSI-X message
re0: turning off MSI enable bit.
re0: ASPM disabled
re0: Chip rev. 0x4c000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
re0: Ethernet address: bc:ee:7b:87:0d:d5
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7d0b000-0xf7d0b3ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel Lynx Point AHCI SATA controller> port 0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f mem 0xf7d0a000-0xf7d0a7ff irq 19 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
wbwd0: DevID 0xc8 DevRev 0x03, will not attach, please report this.
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to accept, logging disabled
DUMMYNET 0xfffffe00031a3d00 with IPv6 initialized (100409)
load_dn_sched dn_sched RR loaded
load_dn_sched dn_sched WF2Q+ loaded
load_dn_sched dn_sched FIFO loaded
load_dn_sched dn_sched PRIO loaded
load_dn_sched dn_sched QFQ loaded
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <ST32000542AS CC34> ATA-8 SATA 2.x device
ada0: Serial Number 5XW1KH8M
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
ada1: <ST32000542AS CC34> ATA-8 SATA 2.x device
ada1: Serial Number 5XW1PX2J
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad6
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST2000DL001-9VT156 CC41> ATA-8 SATA 2.x device
ada2: Serial Number 5YD19QDW
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2: Previously was known as ad8
ada3 at ahcich3 bus 0 scbus3 target 0 lun 0
ada3: <SAMSUNG HD204UI 1AQ10001> ATA-8 SATA 2.x device
ada3: Serial Number S2H7J90B102448
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada3: quirks=0x1<4K>
ada3: Previously was known as ad10
ada4 at ahcich4 bus 0 scbus4 target 0 lun 0
ada4: <WDC WD20EADS-00S2B0 01.00A01> ATA-8 SATA 2.x device
ada4: Serial Number WD-WCAVY4451054
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada4: Previously was known as ad12
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1600033742 Hz quality 1000
Root mount waiting for: usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x8008, class 9/0, rev 2.00/0.05, addr 2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x8000, class 9/0, rev 2.00/0.05, addr 2> on usbus1
uhub2: 6 ports with 6 removable, self powered
uhub3: 8 ports with 8 removable, self powered
Root mount waiting for: usbus1
ugen1.3: <vendor 0x04d9> at usbus1
ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/1.01, addr 3> on usbus1
kbd2 at ukbd0
uhid0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/1.01, addr 3> on usbus1
Trying to mount root from ufs:/dev/ufs/FreeNASs1a [ro]...
mountroot: waiting for device /dev/ufs/FreeNASs1a ...
ugen1.4: <vendor 0x13fe> at usbus1
umass0: <vendor 0x13fe Patriot Memory, class 0/0, rev 2.10/1.10, addr 4> on usbus1
umass0:  SCSI over Bulk-Only; quirks = 0x0100
umass0:6:0:-1: Attached to scbus6
da0 at umass-sim0 bus 0 scbus6 target 0 lun 0
da0: < Patriot Memory PMAP> Removable Direct Access SCSI-6 device
da0: Serial Number 07013A450FB2FA54
da0: 40.000MB/s transfers
da0: 7385MB (15124992 512 byte sectors: 255H 63S/T 941C)
da0: quirks=0x2<NO_6_BYTE>
WARNING: /data was not properly dismounted
GEOM_RAID5: Module loaded, version 1.1.20130907.44 (rev 5c6d2a159411)
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
GEOM_ELI: Device ada0p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: software
GEOM_ELI: Device ada1p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: software
GEOM_ELI: Device ada2p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: software
GEOM_ELI: Device ada3p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: software
GEOM_ELI: Device ada4p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI:     Crypto: software
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Error 5, Retries exhausted
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Error 5, Retries exhausted
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Error 5, Retries exhausted
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Error 5, Retries exhausted
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Error 5, Retries exhausted
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Error 5, Retries exhausted
(ada4:ahcich4:0:0:0): READ_FPDMA_QUEUED. ACB: 60 10 b0 92 69 40 18 00 00 00 00 00
(ada4:ahcich4:0:0:0): CAM status: ATA Status Error
(ada4:ahcich4:0:0:0): ATA status: 41 (DRDY ERR), error: 40 (UNC )
(ada4:ahcich4:0:0:0): RES: 41 40 b1 92 69 40 18 00 00 00 00
(ada4:ahcich4:0:0:0): Retrying command

je coupe ici cas c'impossible de tout poster !

(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Retrying command
(ada2:ahcich2:0:0:0): READ_DMA48. ACB: 25 00 b0 92 69 40 18 00 00 00 18 00
(ada2:ahcich2:0:0:0): CAM status: ATA Status Error
(ada2:ahcich2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
(ada2:ahcich2:0:0:0): RES: 51 40 c0 92 69 00 18 00 00 00 00
(ada2:ahcich2:0:0:0): Error 5, Retries exhausted
vboxdrv: fAsync=0 offMin=0x374 offMax=0xc34

nydjo · Feb 16, 2015

gpart show

Code:

[root@freenas] ~# gpart show
=>        34  3907029101  ada0  GPT  (1.8T)
          34          94        - free -  (47k)
         128     4194304     1  freebsd-swap  (2.0G)
     4194432  3902834696     2  freebsd-zfs  (1.8T)
  3907029128           7        - free -  (3.5k)

=>        34  3907029101  ada1  GPT  (1.8T)
          34          94        - free -  (47k)
         128     4194304     1  freebsd-swap  (2.0G)
     4194432  3902834696     2  freebsd-zfs  (1.8T)
  3907029128           7        - free -  (3.5k)

=>        34  3907029101  ada2  GPT  (1.8T)
          34          94        - free -  (47k)
         128     4194304     1  freebsd-swap  (2.0G)
     4194432  3902834696     2  freebsd-zfs  (1.8T)
  3907029128           7        - free -  (3.5k)

=>        34  3907029101  ada3  GPT  (1.8T)
          34          94        - free -  (47k)
         128     4194304     1  freebsd-swap  (2.0G)
     4194432  3902834696     2  freebsd-zfs  (1.8T)
  3907029128           7        - free -  (3.5k)

=>        34  3907029101  ada4  GPT  (1.8T)
          34          94        - free -  (47k)
         128     4194304     1  freebsd-swap  (2.0G)
     4194432  3902834696     2  freebsd-zfs  (1.8T)
  3907029128           7        - free -  (3.5k)

=>      63  15124929  da0  MBR  (7.2G)
        63   1930257    1  freebsd  [active]  (942M)
   1930320        63       - free -  (31k)
   1930383   1930257    2  freebsd  (942M)
   3860640      3024    3  freebsd  (1.5M)
   3863664     41328    4  freebsd  (20M)
   3904992  11220000       - free -  (5.4G)

=>      0  1930257  da0s1  BSD  (942M)
        0       16         - free -  (8.0k)
       16  1930241      1  !0  (942M)

gpart list

Code:

[root@freenas] ~# gpart list
Geom name: ada0
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada0p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: f06b46a1-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada0p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r0w0e0
   rawuuid: f0766277-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada0
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r1w1e2

Geom name: ada1
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada1p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: f0b28f5e-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada1p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r0w0e0
   rawuuid: f0bdb44b-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada1
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r1w1e2

Geom name: ada2
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada2p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e1
   rawuuid: f10ee815-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada2p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r0w0e0
   rawuuid: f1233fbe-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada2
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e2

Geom name: ada3
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada3p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e1
   rawuuid: f1a6fb51-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada3p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r0w0e0
   rawuuid: f1b1bbff-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada3
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e2

Geom name: ada4
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada4p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: f1f3f359-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada4p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r0w0e0
   rawuuid: f1fcc4dc-546d-11e4-9ad6-bcee7b870dd5
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada4
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r1w1e2

Geom name: da0
modified: false
state: OK
fwheads: 255
fwsectors: 63
last: 15124991
first: 63
entries: 4
scheme: MBR
Providers:
1. Name: da0s1
   Mediasize: 988291584 (942M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 32256
   Mode: r1w0e1
   attrib: active
   rawtype: 165
   length: 988291584
   offset: 32256
   type: freebsd
   index: 1
   end: 1930319
   start: 63
2. Name: da0s2
   Mediasize: 988291584 (942M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 988356096
   Mode: r0w0e0
   rawtype: 165
   length: 988291584
   offset: 988356096
   type: freebsd
   index: 2
   end: 3860639
   start: 1930383
3. Name: da0s3
   Mediasize: 1548288 (1.5M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 1976647680
   Mode: r0w0e0
   rawtype: 165
   length: 1548288
   offset: 1976647680
   type: freebsd
   index: 3
   end: 3863663
   start: 3860640
4. Name: da0s4
   Mediasize: 21159936 (20M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 1978195968
   Mode: r1w1e2
   rawtype: 165
   length: 21159936
   offset: 1978195968
   type: freebsd
   index: 4
   end: 3904991
   start: 3863664
Consumers:
1. Name: da0
   Mediasize: 7743995904 (7.2G)
   Sectorsize: 512
   Mode: r2w1e4

Geom name: da0s1
modified: false
state: OK
fwheads: 255
fwsectors: 63
last: 1930256
first: 0
entries: 8
scheme: BSD
Providers:
1. Name: da0s1a
   Mediasize: 988283392 (942M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 40448
   Mode: r1w0e1
   rawtype: 0
   length: 988283392
   offset: 8192
   type: !0
   index: 1
   end: 1930256
   start: 16
Consumers:
1. Name: da0s1
   Mediasize: 988291584 (942M)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 32256
   Mode: r1w0e1

gpart list adaX je pense que j'ai pas besoin

smartctl -t long /dev/adaX je dois refaire ?

nydjo · Feb 16, 2015

cat /var/log/messages | tail -n 200

Code:

[root@freenas] ~# cat /var/log/messages | tail -n 200
Feb 16 11:00:00 freenas newsyslog[4582]: logfile turned over due to size>100K
Feb 16 11:01:37 freenas notifier: Generating public/private rsa1 key pair.
Feb 16 11:01:37 freenas notifier: Your identification has been saved in /etc/ssh/ssh_host_key.
Feb 16 11:01:37 freenas notifier: Your public key has been saved in /etc/ssh/ssh_host_key.pub.
Feb 16 11:01:37 freenas notifier: The key fingerprint is:
Feb 16 11:01:37 freenas notifier: f2:bd:cd:7d:e5:0a:10:d3:15:0c:ec:6a:06:27:09:e8 root@freenas.local
Feb 16 11:01:37 freenas notifier: The key's randomart image is:
Feb 16 11:01:37 freenas notifier: +--[RSA1 1024]----+
Feb 16 11:01:37 freenas notifier: |     .     ..oo. |
Feb 16 11:01:37 freenas notifier: |    . .    ....  |
Feb 16 11:01:37 freenas notifier: |   .   . .o..    |
Feb 16 11:01:37 freenas notifier: |    E   + .o.    |
Feb 16 11:01:37 freenas notifier: |      . S+..     |
Feb 16 11:01:37 freenas notifier: |       o .+.    .|
Feb 16 11:01:37 freenas notifier: |        .o. .  ..|
Feb 16 11:01:37 freenas notifier: |           + o  o|
Feb 16 11:01:37 freenas notifier: |          . o oo |
Feb 16 11:01:37 freenas notifier: +-----------------+
Feb 16 11:01:37 freenas notifier: Generating public/private dsa key pair.
Feb 16 11:01:37 freenas notifier: Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
Feb 16 11:01:37 freenas notifier: Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
Feb 16 11:01:37 freenas notifier: The key fingerprint is:
Feb 16 11:01:37 freenas notifier: 2b:a9:e7:ab:23:1c:fa:e7:12:21:ef:60:21:0e:92:95 root@freenas.local
Feb 16 11:01:37 freenas notifier: The key's randomart image is:
Feb 16 11:01:37 freenas notifier: +--[ DSA 1024]----+
Feb 16 11:01:37 freenas notifier: |   .             |
Feb 16 11:01:37 freenas notifier: |  E              |
Feb 16 11:01:37 freenas notifier: | o               |
Feb 16 11:01:37 freenas notifier: |*..              |
Feb 16 11:01:37 freenas notifier: |=o..    S        |
Feb 16 11:01:37 freenas notifier: |.o+    . .       |
Feb 16 11:01:37 freenas notifier: |.= o  o .        |
Feb 16 11:01:37 freenas notifier: |. = o...         |
Feb 16 11:01:37 freenas notifier: | ..=+=o.         |
Feb 16 11:01:37 freenas notifier: +-----------------+
Feb 16 11:01:38 freenas notifier: Generating public/private rsa key pair.
Feb 16 11:01:38 freenas notifier: Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
Feb 16 11:01:38 freenas notifier: Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
Feb 16 11:01:38 freenas notifier: The key fingerprint is:
Feb 16 11:01:38 freenas notifier: 0b:b4:f9:c8:e2:16:ee:b7:3e:35:4b:63:45:41:fa:c1 root@freenas.local
Feb 16 11:01:38 freenas notifier: The key's randomart image is:
Feb 16 11:01:38 freenas notifier: +--[ RSA 2048]----+
Feb 16 11:01:38 freenas notifier: |         .o.     |
Feb 16 11:01:38 freenas notifier: |         o.      |
Feb 16 11:01:38 freenas notifier: |      . ..E      |
Feb 16 11:01:38 freenas notifier: |     . o ...     |
Feb 16 11:01:38 freenas notifier: |      + S..      |
Feb 16 11:01:38 freenas notifier: |    .. +*.       |
Feb 16 11:01:38 freenas notifier: |   ...o+o+       |
Feb 16 11:01:38 freenas notifier: |   .o.o .        |
Feb 16 11:01:38 freenas notifier: |   ooooo         |
Feb 16 11:01:38 freenas notifier: +-----------------+
Feb 16 11:01:38 freenas notifier: Generating public/private ecdsa key pair.
Feb 16 11:01:38 freenas notifier: Your identification has been saved in /etc/ssh/ssh_host_ecdsa_key.
Feb 16 11:01:38 freenas notifier: Your public key has been saved in /etc/ssh/ssh_host_ecdsa_key.pub.
Feb 16 11:01:38 freenas notifier: The key fingerprint is:
Feb 16 11:01:38 freenas notifier: 0e:5b:2e:6c:af:ee:36:e5:b3:97:06:36:8f:ef:e5:50 root@freenas.local
Feb 16 11:01:38 freenas notifier: The key's randomart image is:
Feb 16 11:01:38 freenas notifier: +--[ECDSA  256]---+
Feb 16 11:01:38 freenas notifier: |                 |
Feb 16 11:01:38 freenas last message repeated 3 times
Feb 16 11:01:38 freenas notifier: |      . S   E    |
Feb 16 11:01:38 freenas notifier: |     . *=  .     |
Feb 16 11:01:38 freenas notifier: |      =+o=...    |
Feb 16 11:01:38 freenas notifier: |     .oo+ =+     |
Feb 16 11:01:38 freenas notifier: |     ++ooBo .    |
Feb 16 11:01:38 freenas notifier: +-----------------+
Feb 16 11:01:38 freenas notifier: Performing sanity check on sshd configuration.
Feb 16 11:01:38 freenas notifier: Starting sshd.
Feb 16 11:03:52 freenas generate_smb4_conf.py: [common.pipesubr:58] Popen()ing: /sbin/sysctl -n 'kern.maxfilesperproc'
Feb 16 11:03:52 freenas generate_smb4_conf.py: [common.pipesubr:58] Popen()ing: zfs list -H -o mountpoint,name
Feb 16 11:03:52 freenas generate_smb4_conf.py: [common.pipesubr:58] Popen()ing: /usr/local/bin/pdbedit -d 0 -i smbpasswd:/tmp/tmp0DXXtW -s /usr/local/etc/smb4.conf -e tdbsam:/var/etc/private/passdb.tdb
Feb 16 11:03:52 freenas generate_smb4_conf.py: [common.pipesubr:58] Popen()ing: /usr/local/bin/net groupmap list
Feb 16 11:03:52 freenas notifier: Performing sanity check on Samba configuration: OK
Feb 16 11:03:52 freenas notifier: Reloading nmbd.
Feb 16 11:03:52 freenas nmbd[2472]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connectionsdump_workgroups()
Feb 16 11:03:52 freenas nmbd[2472]:    dump workgroup on subnet    192.168.1.40: netmask=  255.255.255.0:
Feb 16 11:03:52 freenas nmbd[2472]:     WORKGROUP(1) current master browser = BUREAU
Feb 16 11:03:52 freenas nmbd[2472]:             FREENAS 40819a23 (FreeNAS Server)
Feb 16 11:03:52 freenas nmbd[2472]:             BUREAU 40051003 ()
Feb 16 11:03:52 freenas notifier: Reloading smbd.
Feb 16 11:03:52 freenas notifier: Reloading winbindd.
Feb 16 11:07:31 freenas smartd[2484]: Device: /dev/ada2, 8 Currently unreadable (pending) sectors
Feb 16 11:07:31 freenas smartd[2484]: Device: /dev/ada2, 8 Offline uncorrectable sectors
Feb 16 11:07:33 freenas smartd[2484]: Device: /dev/ada4, 1 Currently unreadable (pending) sectors
Feb 16 11:07:33 freenas smartd[2484]: Device: /dev/ada4, 1 Offline uncorrectable sectors
Feb 16 11:07:40 freenas notifier: Performing sanity check on sshd configuration.
Feb 16 11:08:09 freenas sshd[6208]: error: Received disconnect from 192.168.1.117: 14: No supported authentication methods available [preauth]
Feb 16 11:08:27 freenas notifier: Performing sanity check on sshd configuration.

smartctl -a /dev/adaX

Code:

[root@freenas] ~# smartctl -a /dev/ada0
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda LP
Device Model:     ST32000542AS
Serial Number:    5XW1KH8M
LU WWN Device Id: 5 000c50 02aa7a795
Firmware Version: CC34
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Feb 16 11:35:33 2015 PST

==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/213915en

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  633) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 447) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   118   099   006    Pre-fail  Always       -       186262612
  3 Spin_Up_Time            0x0003   100   100   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       268
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   078   060   030    Pre-fail  Always       -       65867862
  9 Power_On_Hours          0x0032   096   096   000    Old_age   Always       -       4303
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       299
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   066   060   045    Old_age   Always       -       34 (Min/Max 33/34)
194 Temperature_Celsius     0x0022   034   040   000    Old_age   Always       -       34 (0 19 0 0 0)
195 Hardware_ECC_Recovered  0x001a   035   024   000    Old_age   Always       -       186262612
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       224777113441020
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       3026329891
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       2473515730

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      4290         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Code:

[root@freenas] ~# smartctl -a /dev/ada1
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda LP
Device Model:     ST32000542AS
Serial Number:    5XW1PX2J
LU WWN Device Id: 5 000c50 02ad2c4a5
Firmware Version: CC34
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Feb 16 11:36:44 2015 PST

==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/213915en

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  643) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 458) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   116   099   006    Pre-fail  Always       -       110843013
  3 Spin_Up_Time            0x0003   100   100   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       268
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   078   060   030    Pre-fail  Always       -       4361802544
  9 Power_On_Hours          0x0032   096   096   000    Old_age   Always       -       4315
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       341
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   064   060   045    Old_age   Always       -       36 (Min/Max 35/36)
194 Temperature_Celsius     0x0022   036   040   000    Old_age   Always       -       36 (0 22 0 0 0)
195 Hardware_ECC_Recovered  0x001a   031   020   000    Old_age   Always       -       110843013
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       146273701204746
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       2604755102
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       3516197932

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      4301         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

nydjo · Feb 16, 2015

La suite
je suis obliger de poster ainsi car il y as trop de caractere regarde bien plus haut le 4 derniers messages

Code:

[root@freenas] ~# smartctl -a /dev/ada2
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda Green (AF)
Device Model:     ST2000DL001-9VT156
Serial Number:    5YD19QDW
LU WWN Device Id: 5 000c50 02f2fac08
Firmware Version: CC41
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Mon Feb 16 11:40:53 2015 PST

==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/218171en

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  623) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 345) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   098   098   006    Pre-fail  Always       -       1174049035
  3 Spin_Up_Time            0x0003   093   090   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   099   099   020    Old_age   Always       -       1938
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   068   060   030    Pre-fail  Always       -       21507453007
  9 Power_On_Hours          0x0032   094   094   000    Old_age   Always       -       5839
10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       648
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       651
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       2
189 High_Fly_Writes         0x003a   091   091   000    Old_age   Always       -       9
190 Airflow_Temperature_Cel 0x0022   067   046   045    Old_age   Always       -       33 (Min/Max 32/34)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       289
193 Load_Cycle_Count        0x0032   099   099   000    Old_age   Always       -       2185
194 Temperature_Celsius     0x0022   033   054   000    Old_age   Always       -       33 (0 17 0 0 0)
195 Hardware_ECC_Recovered  0x001a   126   099   000    Old_age   Always       -       1174049035
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       8
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       8
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       123106647611883
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       4145606392
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       1266206406

SMART Error Log Version: 1
ATA Error Count: 645 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 645 occurred at disk power-on lifetime: 5838 hours (243 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 18 ff ff ff 4f 00      00:05:22.143  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:18.850  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:15.446  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:12.143  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:08.909  READ DMA EXT

Error 644 occurred at disk power-on lifetime: 5838 hours (243 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 18 ff ff ff 4f 00      00:05:18.850  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:15.446  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:12.143  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:08.909  READ DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT

Error 643 occurred at disk power-on lifetime: 5838 hours (243 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 18 ff ff ff 4f 00      00:05:15.446  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:12.143  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:08.909  READ DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT

Error 642 occurred at disk power-on lifetime: 5838 hours (243 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 18 ff ff ff 4f 00      00:05:12.143  READ DMA EXT
  25 00 18 ff ff ff 4f 00      00:05:08.909  READ DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT
  ca 00 10 90 02 40 40 00      00:05:08.906  WRITE DMA

Error 641 occurred at disk power-on lifetime: 5838 hours (243 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 18 ff ff ff 4f 00      00:05:08.909  READ DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT
  35 00 10 ff ff ff 4f 00      00:05:08.908  WRITE DMA EXT
  ca 00 10 90 02 40 40 00      00:05:08.906  WRITE DMA
  25 00 10 ff ff ff 4f 00      00:05:08.906  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%      5819         409572032
# 2  Extended offline    Completed: read failure       90%      5819         409572032

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[root@freenas] ~#

Code:

[root@freenas] ~# smartctl -a /dev/ada3
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F4 EG (AF)
Device Model:     SAMSUNG HD204UI
Serial Number:    S2H7J90B102448
LU WWN Device Id: 5 0024e9 2043b5b0b
Firmware Version: 1AQ10001
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Feb 16 11:41:43 2015 PST

==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://knowledge.seagate.com/articles/en_US/FAQ/223571en
http://sourceforge.net/apps/trac/smartmontools/wiki/SamsungF4EGBadBlocks

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (19920) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 332) minutes.
SCT capabilities:              (0x003f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   051    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0026   052   052   000    Old_age   Always       -       19386
  3 Spin_Up_Time            0x0023   068   044   025    Pre-fail  Always       -       9885
  4 Start_Stop_Count        0x0032   098   098   000    Old_age   Always       -       2786
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       11667
10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   252   252   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       169
181 Program_Fail_Cnt_Total  0x0022   100   100   000    Old_age   Always       -       10387
191 G-Sense_Error_Rate      0x0022   100   100   000    Old_age   Always       -       2
192 Power-Off_Retract_Count 0x0022   252   252   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0002   064   061   000    Old_age   Always       -       32 (Min/Max 15/39)
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   252   252   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0036   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       -       14
223 Load_Retry_Count        0x0032   252   252   000    Old_age   Always       -       0
225 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       2836

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     11654         -
# 2  Short offline       Completed without error       00%      3042         -
# 3  Short offline       Completed without error       00%      3035         -
# 4  Short offline       Completed without error       00%      3033         -
# 5  Short offline       Completed without error       00%      3030         -
# 6  Short offline       Completed without error       00%      3027         -
# 7  Extended offline    Aborted by host               90%      3027         -
# 8  Short offline       Completed without error       00%      3025         -
# 9  Short offline       Completed without error       00%      3023         -
#10  Short offline       Completed without error       00%      3021         -
#11  Short offline       Completed without error       00%      3018         -
#12  Short offline       Completed without error       00%      3016         -
#13  Short offline       Completed without error       00%      3014         -
#14  Extended offline    Completed without error       00%      3012         -
#15  Short offline       Aborted by host               90%      3007         -
#16  Short offline       Completed without error       00%      3004         -
#17  Short offline       Completed without error       00%      3001         -
#18  Short offline       Completed without error       00%      2999         -
#19  Short offline       Completed without error       00%      2996         -
#20  Short offline       Completed without error       00%      2992         -
#21  Short offline       Completed without error       00%      2989         -

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Code:


[root@freenas] ~# smartctl -a /dev/ada4
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p12 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar Green
Device Model:     WDC WD20EADS-00S2B0
Serial Number:    WD-WCAVY4451054
LU WWN Device Id: 5 0014ee 259fe62a8
Firmware Version: 01.00A01
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Feb 16 11:43:03 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (40980) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 466) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       1
  3 Spin_Up_Time            0x0027   206   152   021    Pre-fail  Always       -       6675
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       238
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   091   091   000    Old_age   Always       -       7202
10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       148
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       137
193 Load_Cycle_Count        0x0032   193   193   000    Old_age   Always       -       23377
194 Temperature_Celsius     0x0022   113   099   000    Old_age   Always       -       39
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       1
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       1
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%      7183         409572017
# 2  Short offline       Completed without error       00%      4196         -
# 3  Short offline       Aborted by host               70%      4196         -
# 4  Short offline       Completed without error       00%      4194         -
# 5  Short offline       Completed without error       00%      4164         -
# 6  Extended offline    Completed without error       00%      4123         -
# 7  Short offline       Completed without error       00%      3997         -
# 8  Short offline       Completed without error       00%      3830         -
# 9  Short offline       Completed without error       00%      3662         -
#10  Short offline       Completed without error       00%      3495         -
#11  Extended offline    Completed without error       00%      3382         -
#12  Short offline       Completed without error       00%      3328         -
#13  Short offline       Completed without error       00%      3161         -
#14  Short offline       Completed without error       00%      2993         -
#15  Short offline       Completed without error       00%      2941         -
#16  Short offline       Completed without error       00%      2828         -
#17  Short offline       Completed without error       00%      2660         -
#18  Extended offline    Aborted by host               90%      2660         -
#19  Short offline       Completed without error       00%      2494         -
#20  Short offline       Completed without error       00%      2327         -
#21  Short offline       Completed without error       00%      2159         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

-a /dev/adaX
La sa cloche

Code:


[root@freenas] ~#  -a /dev/ada0
-a: Command not found.
[root@freenas] ~# -a /dev/ada1
-a: Command not found.
[root@freenas] ~# -a /dev/ada2
-a: Command not found.
[root@freenas] ~# -a /dev/ada3
-a: Command not found.
[root@freenas] ~# a /dev/ada3
a: Command not found.
[root@freenas] ~# -a /dev/ada4
-a: Command not found.

Bidule0hm · Feb 16, 2015

Ok, parfait, merci ;)

Bon ada2 et ada4 sont effectivement en train de [commencer à] mourir.

Gpart show ne segfault plus sur ada4 et gpart list arrive même à correctement voir les partitions, c'est vraiment étrange (mais bon signe) vu que hier tout laissait à penser que ada4 était mort pour de bon. Je me demande si t'as pas un problème de câbles (faux-contact) ou d'alim (mais en principe Antec fait de bonnes alims) en plus du reste.

La question est de savoir si t'as assez de redondance pour monter la pool et faire une backup de ce qu'il y a dessus.

Qu'est-ce que la commande zpool import te sors ?

nydjo · Feb 16, 2015

Bon l'alim est vieille es je suis pret a en changer c'es pas le problème
le Problème de cablage me semble pas mal surtout après une coupure de courant !!!
Ca serait vraiment simple pour solutionner tout ça

Code:

[root@freenas] ~# zpool import
   pool: tank
     id: 18416255718950753427
  state: ONLINE
action: The pool can be imported using its name or numeric identifier.
config:

        tank                                            ONLINE
          raidz1-0                                      ONLINE
            gptid/f0766277-546d-11e4-9ad6-bcee7b870dd5  ONLINE
            gptid/f0bdb44b-546d-11e4-9ad6-bcee7b870dd5  ONLINE
            gptid/f1233fbe-546d-11e4-9ad6-bcee7b870dd5  ONLINE
            gptid/f1b1bbff-546d-11e4-9ad6-bcee7b870dd5  ONLINE
            gptid/f1fcc4dc-546d-11e4-9ad6-bcee7b870dd5  ONLINE

je vois raidz1 oups !!!

Bidule0hm · Feb 16, 2015

Ok, ça semble en bonne voie, tente cette commande pour monter la pool zpool import -R /mnt tank et donne moi le résultat ;)

nydjo · Feb 16, 2015

[root@freenas] ~# zpool import -R /mnt tank
cannot import 'tank': one or more devices is currently unavailable

Bidule0hm · Feb 16, 2015

Hum...

Re-exécute zpool import pour voir ?

Important Announcement for the TrueNAS Community.

[Message Erreur]Cam status: ATA status Error

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Explorer

Explorer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Explorer

Server Electronics Sorcerer

Important Announcement for the TrueNAS Community.

Related topics on forums.truenas.com for thread: "[Message Erreur]Cam status: ATA status Error"

Similar threads