esamett
Patron
- Joined
- May 28, 2011
- Messages
- 345
Security output email today:
Smart error email message:
smartctl -a /dev/da9 output:
Long smart test started:
Question: Bad drive, cable, Halloween gremlins? I searched the error on this forum and the one result I saw diagnosed a bad backplane after multiple disks errors noted. I have 8087 to SATA fan cables in use. This is the only error that has come up recently after I changed a bad cable and wiped out the old errors from an old 2TB drive. I briefly had temps to around 40'C while heating my room while PRIME95 testing my desktop. Otherwise no FreeNAS issues at all for about two months.
Thanks...as always.
Code:
freenas.domain kernel log messages: > (da9:mps1:0:2:0): READ(10). CDB: 28 00 1d 98 2c e0 00 00 20 00 length 16384 SMID 875 terminated ioc 804b scsi 0 state 0 xfer 0 > (da9:mps1:0:2:0): READ(10). CDB: 28 00 1d 98 2c c0 00 00 20 00 > (da9:mps1:0:2:0): CAM status: SCSI Status Error > (da9:mps1:0:2:0): SCSI status: Check Condition > (da9:mps1:0:2:0): SCSI sense: ABORTED COMMAND asc:47,3 (Information unit iuCRC error detected) > (da9:mps1:0:2:0): Retrying command (per sense data) -- End of security output --
Smart error email message:
Code:
Subject: SMART error (ErrorCount) detected on host: freenas This message was generated by the smartd daemon running on: host name: freenas DNS domain: domain The following warning/error was logged by the smartd daemon: Device: /dev/da9 [SAT], ATA error count increased from 0 to 1 Device info: HGST HDN724040ALE640, S/N:PK2381PBHATTLR, WWN:5-000cca-23dd30049, FW:MJAOA5E0, 4.00 TB For details see host's SYSLOG. You can also use the smartctl utility for further investigation. No additional messages about this problem will be sent.
smartctl -a /dev/da9 output:
Code:
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p10 amd64] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HGST HDN724040ALE640 Serial Number: PK2381PBHATTLR LU WWN Device Id: 5 000cca 23dd30049 Firmware Version: MJAOA5E0 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Oct 31 18:14:17 2014 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 556) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 80 3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 605 (Average 576) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 26 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1981 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 97 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 97 194 Temperature_Celsius 0x0002 171 171 000 Old_age Always - 35 (Min/Max 24/50) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 2 SMART Error Log Version: 1 ATA Error Count: 2 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 occurred at disk power-on lifetime: 1974 hours (82 days + 6 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 27 e1 6d 00 Error: ICRC, ABRT at LBA = 0x006de127 = 7201063 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 00 08 e1 6d 40 00 1d+03:06:22.004 READ FPDMA QUEUED 60 20 00 e8 e0 6d 40 00 1d+03:06:22.004 READ FPDMA QUEUED 60 20 00 c8 e0 6d 40 00 1d+03:06:22.004 READ FPDMA QUEUED 60 20 00 a8 e0 6d 40 00 1d+03:06:22.002 READ FPDMA QUEUED 60 20 00 88 e0 6d 40 00 1d+03:06:22.001 READ FPDMA QUEUED Error 1 occurred at disk power-on lifetime: 1965 hours (81 days + 21 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 df 2c 98 0d Error: ICRC, ABRT at LBA = 0x0d982cdf = 228076767 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 18 e0 2c 98 40 00 18:14:52.246 READ FPDMA QUEUED 60 20 10 c0 2c 98 40 00 18:14:52.246 READ FPDMA QUEUED 60 20 08 a0 2c 98 40 00 18:14:52.246 READ FPDMA QUEUED 60 20 00 80 2c 98 40 00 18:14:52.246 READ FPDMA QUEUED 60 08 00 48 e8 58 40 00 18:14:52.246 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short offline Completed without error 00% 1057 - # 2 Short offline Completed without error 00% 1015 - # 3 Short offline Completed without error 00% 967 - # 4 Short offline Completed without error 00% 919 - # 5 Short offline Completed without error 00% 871 - # 6 Short offline Completed without error 00% 823 - # 7 Short offline Completed without error 00% 775 - # 8 Extended offline Completed without error 00% 762 - # 9 Short offline Completed without error 00% 727 - #10 Short offline Completed without error 00% 679 - #11 Short offline Completed without error 00% 633 - #12 Short offline Completed without error 00% 585 - #13 Short offline Completed without error 00% 561 - #14 Short offline Completed without error 00% 513 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Long smart test started:
Code:
[root@freenas ~]# smartctl -t long /dev/da9 smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p10 amd64] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Extended self-test routine immediately in off-li ne mode". Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 556 minutes for test to complete. Test will complete after Sat Nov 1 03:41:18 2014 Use smartctl -X to abort test. [root@freenas ~]#
Question: Bad drive, cable, Halloween gremlins? I searched the error on this forum and the one result I saw diagnosed a bad backplane after multiple disks errors noted. I have 8087 to SATA fan cables in use. This is the only error that has come up recently after I changed a bad cable and wiped out the old errors from an old 2TB drive. I briefly had temps to around 40'C while heating my room while PRIME95 testing my desktop. Otherwise no FreeNAS issues at all for about two months.
Thanks...as always.