Hi all,
I bought 2x Seagate Exos X16 12TB, which are not showing up in the Web UI, but they do in camcontrol(8):
```
# camcontrol devlist
<ST12000NM001G-2MV103 SN03> at scbus0 target 0 lun 0 (pass0,ada0)
<ST12000NM001G-2MV103 SN03> at scbus1 target 0 lun 0 (pass1,ada1)
<WDC WD60EFRX-68L0BN1 82.00A82> at scbus2 target 0 lun 0 (pass2,ada2)
<WDC WD60EFRX-68L0BN1 82.00A82> at scbus3 target 0 lun 0 (pass3,ada3)
<ST6000VN001-2BB186 SC60> at scbus4 target 0 lun 0 (pass4,ada4)
<ST6000VN001-2BB186 SC60> at scbus6 target 0 lun 0 (pass5,ada5)
```
Note the first 2 lines, which are the new 2 disks.
I've also tried `gpart create -s gpt /dev/ada0` and `gpart create -s gpt /dev/ada1`, followed by `gpart destroy -F /dev/ada0` and `gpart destroy -F /dev/ada1`, but they are still not showing up in the Web UI, even after a few reboots.
I've been referring to https://www.truenas.com/docs/core/storage/disks/diskreplace/, but I can´t select a new member disk.
They are also not showing up in http://truenas.local/ui/storage/disks.
I also ran smartctl(8) on both and found nothing wrong with the disks:
```
# smartctl -a /dev/ada0
smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Exos X16
Device Model: ST12000NM001G-2MV103
Serial Number: REDACTED
LU WWN Device Id: 5 000c50 0db9ef421
Firmware Version: SN03
User Capacity: 12,000,138,625,024 bytes [12.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 27 22:15:37 2021 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1106) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 044 Pre-fail Always - 3330
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always - 1895
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 1
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4
18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 253 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 051 040 Old_age Always - 34 (Min/Max 34/34)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 15
194 Temperature_Celsius 0x0022 034 040 000 Old_age Always - 34 (0 23 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 0h+00m+44.491s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 207
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3123
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
```
I must be doing something wrong, but I've been at it for a few hours now and I can´t figure it out.
Perhaps anyone can help me out?
I bought 2x Seagate Exos X16 12TB, which are not showing up in the Web UI, but they do in camcontrol(8):
```
# camcontrol devlist
<ST12000NM001G-2MV103 SN03> at scbus0 target 0 lun 0 (pass0,ada0)
<ST12000NM001G-2MV103 SN03> at scbus1 target 0 lun 0 (pass1,ada1)
<WDC WD60EFRX-68L0BN1 82.00A82> at scbus2 target 0 lun 0 (pass2,ada2)
<WDC WD60EFRX-68L0BN1 82.00A82> at scbus3 target 0 lun 0 (pass3,ada3)
<ST6000VN001-2BB186 SC60> at scbus4 target 0 lun 0 (pass4,ada4)
<ST6000VN001-2BB186 SC60> at scbus6 target 0 lun 0 (pass5,ada5)
```
Note the first 2 lines, which are the new 2 disks.
I've also tried `gpart create -s gpt /dev/ada0` and `gpart create -s gpt /dev/ada1`, followed by `gpart destroy -F /dev/ada0` and `gpart destroy -F /dev/ada1`, but they are still not showing up in the Web UI, even after a few reboots.
I've been referring to https://www.truenas.com/docs/core/storage/disks/diskreplace/, but I can´t select a new member disk.
They are also not showing up in http://truenas.local/ui/storage/disks.
I also ran smartctl(8) on both and found nothing wrong with the disks:
```
# smartctl -a /dev/ada0
smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Exos X16
Device Model: ST12000NM001G-2MV103
Serial Number: REDACTED
LU WWN Device Id: 5 000c50 0db9ef421
Firmware Version: SN03
User Capacity: 12,000,138,625,024 bytes [12.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 27 22:15:37 2021 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1106) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 044 Pre-fail Always - 3330
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always - 1895
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 1
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4
18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 253 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 051 040 Old_age Always - 34 (Min/Max 34/34)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 15
194 Temperature_Celsius 0x0022 034 040 000 Old_age Always - 34 (0 23 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 0h+00m+44.491s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 207
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3123
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
```
I must be doing something wrong, but I've been at it for a few hours now and I can´t figure it out.
Perhaps anyone can help me out?