depasseg
FreeNAS Replicant
- Joined
- Sep 16, 2014
- Messages
- 2,874
I have a strange problem, and I could really use help. I have 2 systems (freenas1 and freenas2). Specs are in my sig, but fn1 has an external SC847 enclosure, and fn2 is a repurposed Netgear Readynas pro6. I had 6x6TB Seagate drive in fn2. One died, did an RMA and got a recertified drive in return. To expedite replication, I moved all 6 drives into thefn1 sc847 for the initial replication. All was good. Detached the 6 drive backup pool from fn1 and installed the drives in fn2. The recertified drive wasn't detected. I swapped drives around in fn2 and no matter where it was, the recertified drive wasn't detected (at boot). So I move the drive back to fn1, and it's detected just fine. I'm kinda at a loss. Any ideas?
Code:
mpssas_get_sata_identify: error reading SATA PASSTHRU; iocstatus = 0x47 mps0: Sleeping 3 seconds after SATA ID error to wait for spinup mps0: SAS Address for SATA device = 3b2d3b3a71ad5158 mps0: SAS Address from SATA device = 3b2d3b3a71ad5158 da41 at mps0 bus 0 scbus5 target 41 lun 0 da41: <ATA ST6000DX000-1H21 CC48> Fixed Direct Access SCSI-6 device da41: Serial Number Z4D07NJZ da41: 600.000MB/s transfers da41: Command Queueing enabled da41: 5723166MB (11721045168 512 byte sectors: 255H 63S/T 729601C) ses2: da41,pass46: Element descriptor: 'Slot 10' ses2: da41,pass46: SAS Device Slot Element: 1 Phys at Slot 9 ses2: phy 0: SATA device ses2: phy 0: parent 50030480017041ff addr 50030480017041d1 GEOM: da41: the secondary GPT header is not in the last LBA. mps0: mpssas_prepare_remove: Sending reset for target ID 41 da41 at mps0 bus 0 scbus5 target 41 lun 0 da41: <ATA ST6000DX000-1H21 CC48> s/n Z4D07NJZ detached mps0: Unfreezing devq for target ID 41 (da41:mps0:0:41:0): Periph destroyed mpssas_get_sata_identify: error reading SATA PASSTHRU; iocstatus = 0x47 mps0: Sleeping 3 seconds after SATA ID error to wait for spinup mps0: SAS Address for SATA device = 3b2d3b3a71ad5158 mps0: SAS Address from SATA device = 3b2d3b3a71ad5158 da41 at mps0 bus 0 scbus5 target 41 lun 0 da41: <ATA ST6000DX000-1H21 CC48> Fixed Direct Access SCSI-6 device da41: Serial Number Z4D07NJZ da41: 600.000MB/s transfers da41: Command Queueing enabled da41: 5723166MB (11721045168 512 byte sectors: 255H 63S/T 729601C) ses2: da41,pass46: Element descriptor: 'Slot 10' ses2: da41,pass46: SAS Device Slot Element: 1 Phys at Slot 9 ses2: phy 0: SATA device ses2: phy 0: parent 50030480017041ff addr 50030480017041d1
Code:
(aprobe5:ahcich5:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe5:ahcich5:0:0:0): CAM status: ATA Status Error (aprobe5:ahcich5:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe5:ahcich5:0:0:0): RES: 51 04 00 00 00 40 00 00 00 46 00 (aprobe5:ahcich5:0:0:0): Retrying command (aprobe5:ahcich5:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 46 00 (aprobe5:ahcich5:0:0:0): CAM status: ATA Status Error (aprobe5:ahcich5:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe5:ahcich5:0:0:0): RES: 51 04 00 00 00 40 00 00 00 46 00 (aprobe5:ahcich5:0:0:0): Error 5, Retries exhausted
Code:
[root@freenas1] ~# camcontrol identify da41 pass46: <ST6000DX000-1H217Z CC48> ATA-10 SATA 3.x device pass46: 600.000MB/s transfers, Command Queueing Enabled protocol ATA/ATAPI-10 SATA 3.x device model ST6000DX000-1H217Z firmware revision CC48 serial number Z4D07NJZ WWN 5000c5005d25ec0b cylinders 16383 heads 16 sectors/track 63 sector size logical 512, physical 4096, offset 0 LBA supported 268435455 sectors LBA48 supported 11721045168 sectors PIO supported PIO4 DMA supported WDMA2 UDMA6 media RPM 7200 Feature Support Enabled Value Vendor read ahead yes yes write cache yes yes flush cache yes yes overlap no Tagged Command Queuing (TCQ) no no Native Command Queuing (NCQ) yes 32 tags NCQ Queue Management no NCQ Streaming no Receive & Send FPDMA Queued no SMART yes yes microcode download yes yes security yes no power management yes yes advanced power management yes no 0/0x00 automatic acoustic management no no media status notification no no power-up in Standby yes no write-read-verify yes no 0/0x0 unload yes yes general purpose logging yes yes free-fall no no Data Set Management (DSM/TRIM) no Host Protected Area (HPA) no [root@freenas1] ~#
Code:
[root@freenas2] ~# camcontrol identify ada0 pass0: <ST6000DX000-1H217Z CC48> ATA-10 SATA 3.x device pass0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) protocol ATA/ATAPI-10 SATA 3.x device model ST6000DX000-1H217Z firmware revision CC48 serial number Z4D1AADE WWN 5000c5007ac9f913 cylinders 16383 heads 16 sectors/track 63 sector size logical 512, physical 4096, offset 0 LBA supported 268435455 sectors LBA48 supported 11721045168 sectors PIO supported PIO4 DMA supported WDMA2 UDMA6 media RPM 7200 Feature Support Enabled Value Vendor read ahead yes yes write cache yes yes flush cache yes yes overlap no Tagged Command Queuing (TCQ) no no Native Command Queuing (NCQ) yes 32 tags NCQ Queue Management no NCQ Streaming no Receive & Send FPDMA Queued no SMART yes yes microcode download yes yes security yes no power management yes yes advanced power management yes no 0/0x00 automatic acoustic management no no media status notification no no power-up in Standby yes no write-read-verify yes no 0/0x0 unload yes yes general purpose logging yes yes free-fall no no Data Set Management (DSM/TRIM) no Host Protected Area (HPA) no [root@freenas2] ~#
Last edited: