TrueNas Cobia rls 23.10.0.1 Fails to find Network Card

[kulbir]

I am using TRUNAS Cobia Nightly, I have two issues, any help will be appreciated:

Operation	Name
Upgrade	TrueNAS-23.10-MASTER-20231109-042812 -> TrueNAS-23.10-MASTER-20231116-033818

Check Release Notes

Situation 1: Can not upgrade Nightlies any more fails with the following Message



File "/usr/lib/python3.11/concurrent/futures/thread.py", line 58, in run result = self.fn(*self.args, **self.kwargs) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ File "/usr/lib/python3/dist-packages/middlewared/plugins/alert.py", line 943, in alert_source_clear_run raise CallError(f"Alert source {name!r} not found.", errno.ENOENT) middlewared.service_exception.CallError: [ENOENT] Alert source 'HasUpdate' not found.

Situation 2:

I thought I would update my server to 23.10.0.1, system loads what the network interface fails to connect And on CLI I read web interface is not available

 

[kulbir]

my card info while booted in Nightly as stated above is as follows
root@truenas:~# ifconfig
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 1xx.xx.xx.xxx netmask 255.255.255.0 broadcast 172.16.1.255
ether xx;xx;xx;xx;xx;xx txqueuelen 1000 (Ethernet)
RX packets 1100 bytes 168981 (165.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 519 bytes 100013 (97.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20 memory 0xfe700000-fe720000

 

[NugentS]

At the top of the forum page is a "Forum Rules". The most important of these is that you have to post your hardware so we have some idea what you are talking about.

 

[kulbir]

what will be the command to get hw config that i can load here I have attached a a capture from LSCPU command

Thanks

 

[NugentS]

There isn't one.
Just list your hardware please - have a look at my signature for ideas of what is needed

 

[kulbir]

I have an American Trend bios server 2ith 8 G RAM and 4 HDDs in raid format server has two network cards. I only use 1 network card

 

[kulbir]

in past I use to use "HWinfo" to list the hw but that is not working anymore

 

[NugentS]

@kulbir try again - please post your hardware, not some abstract almost useless sentence. Again - look at my signature for a guide

 

[kulbir]

I am having hard time providing the info youi are requesting here is another tryu

Primary NAs
Model name: Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz
BIOS Model name: Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz CPU @ 3.1GHz

Ram ; 8 G

Network : 2 ports 1G each
Storage:

1 Pool RAIDZ1 4 Drives
#1 WD-WMAZA3902380 1.82 TiB
Model: WDC_WD20EARS-00MVWB0
Transfer Mode: Auto
Rotation Rate (RPM):N/A
HDD Standby:ALWAYS ON
Adv. Power Management:DISABLED
Enable S.M.A.R.T.: true
S.M.A.R.T. extra options: N/A



#2 W520VK6Z 1.82 TiB
Model: ST2000VN000-1HJ164
Transfer Mode:Auto
Rotation Rate (RPM):5900
HDD Standby: ALWAYS ON
Adv. Power Management: DISABLED
Enable S.M.A.R.T.: true
S.M.A.R.T. extra options: N/A

#3 WD-WX32DC1P0XVN 3.64 TiB
Model: WDC_WD40EFZX-68AWUN0
Transfer Mode: Auto
Rotation Rate (RPM): 5400
HDD Standby: ALWAYS ON
Adv. Power Management: DISABLED
Enable S.M.A.R.T.: true
S.M.A.R.T. extra options: N/A

#4 W520VJ53 1.82 TiB
Model: ST2000VN000-1HJ164
Transfer Mode: Auto
Rotation Rate (RPM): 5900
HDD Standby: ALWAYS ON
Adv. Power Management: DISABLED
Enable S.M.A.R.T.: true
S.M.A.R.T. extra options: N/A


1 Boot Drive
WD-WCAV24676434 298.09 GiB boot-pool

 

[winnielinnie]

So about that network card...

 

[danb35]

I am having hard time providing the info youi are requesting here is another tryu

If you have this little of an idea of what hardware you're using, you probably don't have any business running Nightly code--can it really have not been obvious to you that the type of network device you have would be critical to helping you here? And yet, after six of your posts in this thread, none of us have any idea what motherboard or network interface you're using. Even after you've been asked repeatedly for this information.

 

[NugentS]

yeah - I am out

 

[kulbir]

Thanks every one trying to help finaly found a command to read what card I have and here is capture