HumbleTechie
Cadet
- Joined
- Apr 6, 2017
- Messages
- 3
I need some assistance reading logs from tests. I noticed this error as a critical alert in FreeNAS:
Device: /dev/ada0, 1 Currently unreadable (pending) sectors
Current setup:
3x2TB WD Red
After running smart long test on ada0:
It seems as though everything is passing except the 1 pending sector?
Is this enough to RMA the drive?
Device: /dev/ada0, 1 Currently unreadable (pending) sectors
Current setup:
3x2TB WD Red
Code:
zpool status pool: Primary_Storage state: ONLINE status: Some supported features are not enabled on the pool. The pool can still be used, but some features are unavailable. action: Enable all features using 'zpool upgrade'. Once this is done, the pool may no longer be accessible by software that does not support the features. See zpool-features(7) for details. scan: scrub repaired 0 in 3h10m with 0 errors on Sun Apr 2 03:10:47 2017 config: NAME STATE READ WRITE CKSUM Primary_Storage ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 gptid/8f5428f2-6e04-11e4-b897-448a5bce7ef7 ONLINE 0 0 0 gptid/90084381-6e04-11e4-b897-448a5bce7ef7 ONLINE 0 0 0 gptid/90ba66f0-6e04-11e4-b897-448a5bce7ef7 ONLINE 0 0 0 errors: No known data errors pool: freenas-boot state: ONLINE scan: scrub repaired 0 in 0h1m with 0 errors on Sun Apr 2 03:46:01 2017 config: NAME STATE READ WRITE CKSUM freenas-boot ONLINE 0 0 0 da0p2 ONLINE 0 0 0 errors: No known data errors
After running smart long test on ada0:
Code:
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 264) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 9 3 Spin_Up_Time 0x0027 172 172 021 Pre-fail Always - 4400 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 32 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 20642 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 32 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 22 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 210 194 Temperature_Celsius 0x0022 119 112 000 Old_age Always - 28 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 -- > 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 1 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 8 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20589 - # 2 Extended offline Completed without error 00% 20575 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
It seems as though everything is passing except the 1 pending sector?
Is this enough to RMA the drive?