ada2 is having problem. The rest of the Disk are okay. ada2 configured as no RAID
Code:
smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68AX9N0
Serial Number: WD-WMC1T0615162
LU WWN Device Id: 5 0014ee 6ad7b4580
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Apr 30 22:48:49 2017 MYT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (41760) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 418) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 197 197 051 - 36031
3 Spin_Up_Time POS--K 185 176 021 - 5708
4 Start_Stop_Count -O--CK 100 100 000 - 87
5 Reallocated_Sector_Ct PO--CK 190 190 140 - 318
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 055 055 000 - 33505
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 87
192 Power-Off_Retract_Count -O--CK 200 200 000 - 38
193 Load_Cycle_Count -O--CK 200 200 000 - 48
194 Temperature_Celsius -O---K 115 111 000 - 35
196 Reallocated_Event_Count -O--CK 172 172 000 - 28
197 Current_Pending_Sector -O--CK 200 200 000 - 30
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 33203 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 33203 [10] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 02 00 40 00 Error: UNC at LBA = 0x00000200 = 512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:40.203 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:37.228 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:34.242 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:31.334 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:28.663 READ DMA
Error 33202 [9] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 02 00 40 00 Error: UNC at LBA = 0x00000200 = 512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:37.228 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:34.242 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:31.334 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:28.663 READ DMA
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:28.661 READ LOG EXT
Error 33201 [8] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 02 00 40 00 Error: UNC at LBA = 0x00000200 = 512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:34.242 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:31.334 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:28.663 READ DMA
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:28.661 READ LOG EXT
60 01 00 00 f8 00 00 00 00 00 00 40 08 00:08:25.832 READ FPDMA QUEUED
Error 33200 [7] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 02 00 40 00 Error: UNC at LBA = 0x00000200 = 512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:31.334 READ DMA
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:28.663 READ DMA
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:28.661 READ LOG EXT
60 01 00 00 f8 00 00 00 00 00 00 40 08 00:08:25.832 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:25.831 READ LOG EXT
Error 33199 [6] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 02 00 40 00 Error: UNC at LBA = 0x00000200 = 512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 00 00 00 00 00 02 00 40 08 00:08:28.663 READ DMA
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:28.661 READ LOG EXT
60 01 00 00 f8 00 00 00 00 00 00 40 08 00:08:25.832 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:25.831 READ LOG EXT
60 01 00 00 e8 00 00 00 00 00 00 40 08 00:08:23.001 READ FPDMA QUEUED
Error 33198 [5] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 f8 00 00 00 00 00 00 40 08 00:08:25.832 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:25.831 READ LOG EXT
60 01 00 00 e8 00 00 00 00 00 00 40 08 00:08:23.001 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:23.000 READ LOG EXT
60 01 00 00 d8 00 00 00 00 00 00 40 08 00:08:20.182 READ FPDMA QUEUED
Error 33197 [4] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 e8 00 00 00 00 00 00 40 08 00:08:23.001 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:23.000 READ LOG EXT
60 01 00 00 d8 00 00 00 00 00 00 40 08 00:08:20.182 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:20.181 READ LOG EXT
60 01 00 00 c8 00 00 00 00 00 00 40 08 00:08:17.341 READ FPDMA QUEUED
Error 33196 [3] occurred at disk power-on lifetime: 33504 hours (1396 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 d8 00 00 00 00 00 00 40 08 00:08:20.182 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:20.181 READ LOG EXT
60 01 00 00 c8 00 00 00 00 00 00 40 08 00:08:17.341 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 40 08 00:08:17.339 READ LOG EXT
60 01 00 00 b8 00 00 00 00 00 00 40 08 00:08:14.215 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 33494 0
# 2 Extended offline Completed: read failure 90% 33481 0
# 3 Extended offline Completed: read failure 90% 33479 0
# 4 Extended offline Completed: read failure 90% 33479 0
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 35 Celsius
Power Cycle Min/Max Temperature: 27/35 Celsius
Lifetime Min/Max Temperature: 27/39 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (75)
Index Estimated Time Temperature Celsius
76 2017-04-30 14:51 35 ****************
... ..( 40 skipped). .. ****************
117 2017-04-30 15:32 35 ****************
118 2017-04-30 15:33 34 ***************
... ..( 69 skipped). .. ***************
188 2017-04-30 16:43 34 ***************
189 2017-04-30 16:44 ? -
190 2017-04-30 16:45 27 ********
191 2017-04-30 16:46 28 *********
192 2017-04-30 16:47 29 **********
193 2017-04-30 16:48 30 ***********
194 2017-04-30 16:49 30 ***********
195 2017-04-30 16:50 30 ***********
196 2017-04-30 16:51 31 ************
197 2017-04-30 16:52 31 ************
198 2017-04-30 16:53 31 ************
199 2017-04-30 16:54 32 *************
... ..( 2 skipped). .. *************
202 2017-04-30 16:57 32 *************
203 2017-04-30 16:58 33 **************
... ..( 2 skipped). .. **************
206 2017-04-30 17:01 33 **************
207 2017-04-30 17:02 34 ***************
... ..( 5 skipped). .. ***************
213 2017-04-30 17:08 34 ***************
214 2017-04-30 17:09 35 ****************
... ..( 26 skipped). .. ****************
241 2017-04-30 17:36 35 ****************
242 2017-04-30 17:37 34 ***************
... ..( 69 skipped). .. ***************
312 2017-04-30 18:47 34 ***************
313 2017-04-30 18:48 35 ****************
... ..(239 skipped). .. ****************
75 2017-04-30 22:48 35 ****************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 3425 Vendor specific