Diekatzchen
Dabbler
- Joined
- Apr 10, 2012
- Messages
- 45
Code:
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA300 Serial Number: Z37G3E1GS LU WWN Device Id: 5 000039 ff4d4818a Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Feb 1 22:25:52 2018 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status command failed: Input/output error SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22652) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 378) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 056 056 016 Pre-fail Always - 499983751 2 Throughput_Performance 0x0005 139 139 054 Pre-fail Offline - 73 3 Spin_Up_Time 0x0007 196 196 024 Pre-fail Always - 309 (Average 275) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 87 5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 2005 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33 9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 33698 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 87 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 366 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 366 194 Temperature_Celsius 0x0002 166 166 000 Old_age Always - 36 (Min/Max 23/44) 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 3184 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 5 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 occurred at disk power-on lifetime: 33686 hours (1403 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 d8 d8 dc 45 0b Error: UNC 216 sectors at LBA = 0x0b45dcd8 = 189127896 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 b0 dc 45 40 00 18:20:52.116 READ DMA EXT 60 00 b8 b0 db 45 40 00 18:20:26.285 READ FPDMA QUEUED ef 02 00 00 00 00 40 00 18:20:26.285 SET FEATURES [Enable write cache] ef aa 00 00 00 00 40 00 18:20:26.284 SET FEATURES [Enable read look-ahead] c6 00 10 00 00 00 40 00 18:20:26.284 SET MULTIPLE MODE Error 4 occurred at disk power-on lifetime: 33686 hours (1403 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 88 10 c9 45 0b Error: UNC at LBA = 0x0b45c910 = 189122832 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 78 98 d4 45 40 00 18:15:34.660 READ FPDMA QUEUED 60 00 70 98 d3 45 40 00 18:15:34.660 READ FPDMA QUEUED 60 00 68 98 d2 45 40 00 18:15:34.660 READ FPDMA QUEUED 60 00 60 98 d1 45 40 00 18:15:34.660 READ FPDMA QUEUED 60 00 58 98 d0 45 40 00 18:15:34.660 READ FPDMA QUEUED Error 3 occurred at disk power-on lifetime: 33669 hours (1402 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 30 f8 6a 8d 0b Error: UNC at LBA = 0x0b8d6af8 = 193817336 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 68 28 6e 8d 40 00 01:10:43.736 READ FPDMA QUEUED 60 00 60 28 6d 8d 40 00 01:10:43.736 READ FPDMA QUEUED 60 00 58 28 6c 8d 40 00 01:10:43.736 READ FPDMA QUEUED 60 00 50 28 6b 8d 40 00 01:10:43.736 READ FPDMA QUEUED 60 00 48 28 6a 8d 40 00 01:10:43.736 READ FPDMA QUEUED Error 2 occurred at disk power-on lifetime: 33285 hours (1386 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b0 8b 9d 09 Error: UNC at LBA = 0x099d8bb0 = 161319856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 58 58 85 04 40 00 5d+16:24:38.456 READ FPDMA QUEUED 60 08 50 b0 8b 9d 40 00 5d+16:24:38.438 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 5d+16:24:38.437 READ LOG EXT 60 08 40 b0 8b 9d 40 00 5d+16:24:34.606 READ FPDMA QUEUED 60 08 38 70 28 b2 40 00 5d+16:24:31.718 READ FPDMA QUEUED Error 1 occurred at disk power-on lifetime: 33285 hours (1386 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b0 8b 9d 09 Error: UNC at LBA = 0x099d8bb0 = 161319856 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 40 b0 8b 9d 40 00 5d+16:24:34.606 READ FPDMA QUEUED 60 08 38 70 28 b2 40 00 5d+16:24:31.718 READ FPDMA QUEUED 60 08 30 a8 96 c9 40 00 5d+16:24:31.696 READ FPDMA QUEUED 60 08 28 08 0e cd 40 00 5d+16:24:31.695 READ FPDMA QUEUED 60 08 20 60 0a aa 40 00 5d+16:24:31.694 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
