ethernet

  1. T

    Cheapest dual port 10gbe network card

    I am looking to see what is the least expensive 10 gigabit dual port Ethernet card that is fully supported in FreeNAS 11.2 U5. It can be either copper or sfp+. I found the Intel X540-T2 but with the yottamark it is crazy expensive. I'm aware of the lesser expensive counterfeit cards on ebay...
  2. A

    NIC Suddenly Gone

    Hi all, no matter how I destroy FreeNAS I always forget to create backups on the config lol. My problem here is that I tried accessing plex today, noticed it didn't work so I went to the FreeNAS web GUI and couldn't connect. Weird... So I went to the physical server (HP Proliant DL380G7) to see...
    • aedan929
    • Thread
    • ethernet inaccessable network nic
    • Replies: 8
    • Forum: Hardware
  3. kdragon75

    NetApp CN1610 10gbe First impressions

    I have been looking to move into ten gigabit ethernet for some time and final found a workable switch. Another forum member mentioned having issues with vlans on it and I have not seen it on the "Cheap 10gbe Switch" lists so I did a little research. The NetApp CN1610 is a 16 SFP+ port switch...
  4. A

    Unable to connect to network

    hello, I'm trying to install Freenas on a home-made computer. I followed the installation steps ( boot on flash drive, installation of the system on the SSD.... ) There was no issue until the first reboot, when I start the computer, everything loads, but when I reach the point where it's...
  5. O

    Intel 1219-V (ethernet) not working on new mobo (FreeNAS 11.1)

    Hi, I'm trying FreeNAS 11.1 on a new bit of kit, ASRock 360M Pro4. According to this thread and bug: https://forums.freenas.org/index.php?threads/support-for-i219-v.41608/ This support was merged back in 9.x days. but dmesg shows me "pci0: <network, ethernet> at device 31.6 (no driver attached)"...
  6. E

    Testing FreeNAS 11 in VMware Player NIC unconfigurable

    I downloaded FreeNAS 11 .iso, and tried to run it in VMware Player 14.1.0, using Manjaro linux. The host machine is a Ryzen 1700x with the Asus Prime x370-PRO motherboard. 32 Gigs of ram This has a Intel NIC 26:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03)...
  7. A

    Не могу зайти в WEB GUI по IP после настройки FreeNAS

    написал IP 192.168.1.33 и маску 255,255,255,0 и в шлюзе указал ip маршрутизатора 192,168,1,1, потом захожу в браузер и пишу 192.168.1.33 и ничего, в чем проблема? На серваке (ПКшник) лампочка возле порта ethernet не горит, а если ПК перезагрузить, то она загорится на время загрузки системы, а...
  8. Deepankar

    Ethernet Drop

    Hello , It might be an old topic but I couldn't find any working FIX for it. When I try to copy file to the NAS (I tried both direct wire connect and through the 1gbit switch) which is larger than (<1GB) My Ethernet drops on my Windows machine. After that either I have to restart the adapter or...
  9. N

    Did I Find a Bug?

    While testing a rebuild of my FreeNAS, I booted without the network cable plugged in. I plugged the cable in, and the DHCP assigned an IP Address as expected, but I was not able to log into the WebGUI. I took the extra step of ifconfig em0 down/ifconfig em0 up from the system console, but the...
  10. Uvais Mohammed

    No network interfaces are detected HP Proliant DL180 G6

    Hi, I have installed Freenas on HP180 G6 series and post installation I don't see any ethernet adapters to configure. I just see 1 interface which shows as lo0 which has 127.x.x.x IP address. When I am pressing 1 to configure network interfaces, I don't see any NIC ports. I have also tried...
  11. MauricioU

    SOLVED 10Gbe Transfer Speed issue + Guide?

    SOLVED: So I created a stripe/RAID0 and iperf continued giving me the exact same results, however, with a ramdisk I was getting full 10gbe throughput both ways. I guess with RAIDZ was the bottle neck for the write speeds! =( lol. Also, for anyone using this as a guide, I deleted all the...
Top