Hi all,
New here, config' is there but also below:
- ASrock B550M-ITX
- AMD 3700X
- Corsair H60 AIO
- PNY CS3030 512GB NVME (for jails)
- 128GB San Disk USB (boot) - I planned to mirror it with another USB key (Kingston Data Traveler) but when I attached it to the boot pool, it said it was faulty
- 3*5TB WD RED
- 1*8TB WD White Air (shucked)
- The 4 disks make 1 raidz pool
- 156W AC/DC power brick
- 250W DC/DC PSU
- UDIMM ECC RAM: KSM32ES8/16ME (16GB)
Now, before you roast me for storing the system on USB keys, I know it's not recommended but I needed all SATA ports. I have a backup plan if you tell me the problem comes 100% from those keys.
Everything's fine until it's not: under prolonged load, like restoring my files (7TB) to my new config' over SMB, or sudden seemingly "heavy" load, e.g.
Heading to the messages, I get approx. each second:
And then, when the system hangs, I get:
In the UI, the boot-pool is marked as ONLINE / healthy and I get no alerts. This happens whether I mirror the system over a second key or not.
Now,
No mention of
Thanks!
New here, config' is there but also below:
- ASrock B550M-ITX
- AMD 3700X
- Corsair H60 AIO
- PNY CS3030 512GB NVME (for jails)
- 128GB San Disk USB (boot) - I planned to mirror it with another USB key (Kingston Data Traveler) but when I attached it to the boot pool, it said it was faulty
- 3*5TB WD RED
- 1*8TB WD White Air (shucked)
- The 4 disks make 1 raidz pool
- 156W AC/DC power brick
- 250W DC/DC PSU
- UDIMM ECC RAM: KSM32ES8/16ME (16GB)
Now, before you roast me for storing the system on USB keys, I know it's not recommended but I needed all SATA ports. I have a backup plan if you tell me the problem comes 100% from those keys.
Everything's fine until it's not: under prolonged load, like restoring my files (7TB) to my new config' over SMB, or sudden seemingly "heavy" load, e.g.
mv multi_tb_folder newname
, the UI suddenly hangs and everything is unresponsive until I hard-reboot it.Heading to the messages, I get approx. each second:
Code:
Mar 10 23:59:39 truenas ugen0.5: <Unknown > at usbus0 (disconnected) Mar 10 23:59:39 truenas uhub_reattach_port: could not allocate new device Mar 10 23:59:47 truenas usb_alloc_device: set address 5 failed (USB_ERR_IOERROR, ignored) Mar 10 23:59:47 truenas usbd_setup_device_desc: getting device descriptor at addr 5 failed, USB_ERR_IOERROR
And then, when the system hangs, I get:
Code:
Mar 11 00:00:00 truenas Solaris: WARNING: Pool 'boot-pool' has encountered an uncorrectable I/O failure and has been suspended.
In the UI, the boot-pool is marked as ONLINE / healthy and I get no alerts. This happens whether I mirror the system over a second key or not.
Now,
usbconfig
shows:Code:
root@truenas[~]# usbconfig ugen0.1: <0x1022 XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen1.1: <0x1022 XHCI root HUB> at usbus1, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen1.2: <USB SanDisk 3.2Gen1> at usbus1, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=ON (224mA) ugen0.2: <EATON Eaton 3S> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (20mA) ugen0.3: <ASRock LED Controller> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) ugen0.4: <vendor 0x8087 product 0x0aa7> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA)
No mention of
ugen0.5
, so could this be unrelated to the USB key(s)?Thanks!