USB_ERR_STALLED error out of the blue

[depasseg]

At 8:04am I got a UPS disconnected message on freenas1 (specs below). The console is now filled with these error messages below. I haven't done anything to the server. Any ideas? I'm trying to save a debug, but it's been over 5 minutes. How long does a debug usually take to get created and downloaded?

Code:

Jun 12 09:48:42 freenas1 ugen0.3: <Unknown> at usbus0 (disconnected)
Jun 12 09:48:42 freenas1 uhub_reattach_port: could not allocate new device
Jun 12 09:48:43 freenas1 usb_alloc_device: set address 3 failed (USB_ERR_STALLED, ignored)
Jun 12 09:48:43 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
Jun 12 09:48:44 freenas1 usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
Jun 12 09:48:44 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
Jun 12 09:48:45 freenas1 upsmon[4583]: Poll UPS [ups] failed - Driver not connected
Jun 12 09:48:45 freenas1 usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
Jun 12 09:48:45 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
Jun 12 09:48:45 freenas1 usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
Jun 12 09:48:45 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
Jun 12 09:48:46 freenas1 usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_STALLED, ignored)
Jun 12 09:48:46 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED
Jun 12 09:48:46 freenas1 ugen0.3: <Unknown> at usbus0 (disconnected)
Jun 12 09:48:46 freenas1 uhub_reattach_port: could not allocate new device
Jun 12 09:48:47 freenas1 usb_alloc_device: set address 3 failed (USB_ERR_STALLED, ignored)
Jun 12 09:48:48 freenas1 usbd_setup_device_desc: getting device descriptor at addr 3 failed, USB_ERR_STALLED/CODE]

freenas1 Specs: FreeNAS-9.3-STABLE-201506042008 | Xeon E5-2637V3 | 128GB DDR4 2133MHz ECC RDIMM | X10SRH-CLN4F | On-board LSI 3008 (Flashed v5-IT) | 12x 4TB WD-Re SAS (striped mirrors) | 2x Intel S3700 (SLOG and L2ARC) | SuperMicro SuperStorage Server 5028R-E1CR12L

 

[depasseg]

Well, I solved one problem. Looks like the usb cable was a little loose. I was working in the rack yesterday, and probably bumped something. I guess it slowly worked it's way out.

And the Save Debug finished after 10 minutes. It's 5MB compressed (30 uncompressed). Is that normal? Because after I resolved the USB issue and restarted the UPS service, the Save Debug took ~30 seconds.

 

[Robert Trevellyan]

And the Save Debug finished after 10 minutes. It's 5MB compressed (30 uncompressed). Is that normal? Because after I resolved the USB issue and restarted the UPS service, the Save Debug took ~30 seconds.

My Save Debug always takes minutes, not seconds.

 

[cyberjock]

Mine normally takes 1-2 minutes.