I have upgraded my FreeNAS 9.1.1 to 9.2.1.2 through the web-interface. Everything had seem to be correct, but it wasn't. In my NAS are running some Jails (Owncloud, PLEX, website...) and all this services run perfect, but I can't login in the webinterface of FreeNas. I can ping the IP address of the interface, but it doesn't load, and my hard-disks are not more reachable.
Then I want to restore my old installation. When the server starts, I can see the boot list:
F1 FreeBSD
F2 FreeBSD
F5 Drive
F6
Then I press F2 and it appears one command line but it doesn't start. How can I start the old installation??? I can't access anymore to my Hard-disks.
In the console says:
freenas mDNSResponder: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 0000000000C2FD60 freenas.local. (Addr) that's already in the list.
freenas mDNSResponder: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 0000000000C30180 254.178.168.192.in-addr.arpa. (PTR) that's already in the list.
Hardware:
- Intel Desktop Board D2700DC
- 4 GB RAM
- USB-stick sandisk 8 Gb with FreeNas OS. I have the release 9.1.1 x64 on the stick
- 3 Hard-disks: WD 1TB, 2xWD 3 TB
This system was running with no problem from October.
I made one backup of my system, then I updated the FW to 9.2.1.5-x64 on the web-GUI and everything "seems to be" good. After the system was rebooted, I couldn't load the web GUI of FreeNAS anymore but I could ping the IP.
I check which ports of FreeNAS are listening: Only 22 (SSH). Then I know it's not possible to connect with port 80.
In the system, I checked the option restore defaults. Then I can access to the web GUI and the FW is the new one (9.2.1.5).
So I restore my configuration backup of 9.1.1, and after reboot I have the same problem.
All Jails are running ( Owncloud, PLEX, my own Webserver) but I cannot access to the web interface of freenas and only port 22 is listening.
That was all that I did. I did any change more. I have followed what stay on FreeNAS manual.
"Solution": http://doc.freenas.org/index.php/Upgrading_FreeNAS%C2%AE
I have another one USB stick, so I have install one clean 9.1.1 x-64 release. After the installation I have restored my configuration backup.
Everything runs good. Like from October.
If I want the new release 9.2.1.5, must I configure everything from the beginning?? All my jails, volumen, etc??? I think my backup of 9.1.1 is not compatible with 9.2.1.5.
Do you have any solution for this problem? If you need more information, please let me know.
Daniel
Then I want to restore my old installation. When the server starts, I can see the boot list:
F1 FreeBSD
F2 FreeBSD
F5 Drive
F6
Then I press F2 and it appears one command line but it doesn't start. How can I start the old installation??? I can't access anymore to my Hard-disks.
In the console says:
freenas mDNSResponder: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 0000000000C2FD60 freenas.local. (Addr) that's already in the list.
freenas mDNSResponder: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 0000000000C30180 254.178.168.192.in-addr.arpa. (PTR) that's already in the list.
Hardware:
- Intel Desktop Board D2700DC
- 4 GB RAM
- USB-stick sandisk 8 Gb with FreeNas OS. I have the release 9.1.1 x64 on the stick
- 3 Hard-disks: WD 1TB, 2xWD 3 TB
This system was running with no problem from October.
I made one backup of my system, then I updated the FW to 9.2.1.5-x64 on the web-GUI and everything "seems to be" good. After the system was rebooted, I couldn't load the web GUI of FreeNAS anymore but I could ping the IP.
I check which ports of FreeNAS are listening: Only 22 (SSH). Then I know it's not possible to connect with port 80.
In the system, I checked the option restore defaults. Then I can access to the web GUI and the FW is the new one (9.2.1.5).
So I restore my configuration backup of 9.1.1, and after reboot I have the same problem.
All Jails are running ( Owncloud, PLEX, my own Webserver) but I cannot access to the web interface of freenas and only port 22 is listening.
That was all that I did. I did any change more. I have followed what stay on FreeNAS manual.
"Solution": http://doc.freenas.org/index.php/Upgrading_FreeNAS%C2%AE
I have another one USB stick, so I have install one clean 9.1.1 x-64 release. After the installation I have restored my configuration backup.
Everything runs good. Like from October.
If I want the new release 9.2.1.5, must I configure everything from the beginning?? All my jails, volumen, etc??? I think my backup of 9.1.1 is not compatible with 9.2.1.5.
Do you have any solution for this problem? If you need more information, please let me know.
Daniel