Brailyn
Cadet
- Joined
- Aug 4, 2016
- Messages
- 3
I just added 2x Intel DC S4600 240GB drives to FreeNAS machine to use as a mirrored SLOG. I am running FreeNAS-11.1-U2
I was encouraged to use camcontrol on these drives to make them smaller, and cannot get things to work as per this and this thread.
Some drive info:
The problem:
Any ideas how I can get these drives to be 16GB? Or is HPA really not supported?...
I was encouraged to use camcontrol on these drives to make them smaller, and cannot get things to work as per this and this thread.
Some drive info:
Code:
root@freenas:~ # camcontrol devlist <VMware Virtual disk 2.0> at scbus2 target 0 lun 0 (pass0,da0) <NECVMWar VMware SATA CD00 1.00> at scbus3 target 0 lun 0 (cd0,pass1) <ATA WDC WD40EFRX-68W 0A82> at scbus33 target 7 lun 0 (pass2,da1) <ATA WDC WD40EFRX-68W 0A82> at scbus33 target 8 lun 0 (pass3,da2) <ATA WDC WD40EFRX-68N 0A82> at scbus33 target 9 lun 0 (pass4,da3) <ATA WDC WD40EFRX-68W 0A82> at scbus33 target 10 lun 0 (pass5,da4) <ATA WDC WD40EFRX-68N 0A82> at scbus33 target 11 lun 0 (pass6,da5) <ATA WDC WD40EFRX-68W 0A82> at scbus33 target 12 lun 0 (pass7,da6) <ATA INTEL SSDSC2KG24 0100> at scbus33 target 13 lun 0 (pass8,da7) <ATA INTEL SSDSC2KG24 0100> at scbus33 target 14 lun 0 (pass9,da8) <Intel RES2SV240 0d00> at scbus33 target 15 lun 0 (ses0,pass10) root@freenas:~ # diskinfo -c da7 da7 512 # sectorsize 240057409536 # mediasize in bytes (224G) 468862128 # mediasize in sectors 4096 # stripesize 0 # stripeoffset 29185 # Cylinders according to firmware. 255 # Heads according to firmware. 63 # Sectors according to firmware. ATA INTEL SSDSC2KG24 # Disk descr. BTYM72840CEM240AGN # Disk ident. id1,enc@n5001e677b78acffd/type@0/slot@15/elmdesc@ArrayDevice14 # Physical path Not_Zoned # Zone Mode I/O command overhead: time to read 10MB block 0.040773 sec = 0.002 msec/sector time to read 20480 sectors 2.576243 sec = 0.126 msec/sector calculated command overhead = 0.124 msec/sector root@freenas:~ # diskinfo -c da8 da8 512 # sectorsize 240057409536 # mediasize in bytes (224G) 468862128 # mediasize in sectors 4096 # stripesize 0 # stripeoffset 29185 # Cylinders according to firmware. 255 # Heads according to firmware. 63 # Sectors according to firmware. ATA INTEL SSDSC2KG24 # Disk descr. BTYM729108UG240AGN # Disk ident. id1,enc@n5001e677b78acffd/type@0/slot@16/elmdesc@ArrayDevice15 # Physical path Not_Zoned # Zone Mode I/O command overhead: time to read 10MB block 0.040692 sec = 0.002 msec/sector time to read 20480 sectors 2.434322 sec = 0.119 msec/sector calculated command overhead = 0.117 msec/sector root@freenas:~ # camcontrol security da7 -e camcontrol: option requires an argument -- e camcontrol: option requires an argument -- e pass8: <INTEL SSDSC2KG240G7 SCV10100> ACS-3 ATA SATA 3.x device pass8: 600.000MB/s transfers, Command Queueing Enabled Security Option Value supported yes enabled no drive locked no security config frozen no count expired no security level high enhanced erase supported yes erase time 4 min enhanced erase time 4 min master password rev fffe root@freenas:~ # camcontrol security da8 -e camcontrol: option requires an argument -- e camcontrol: option requires an argument -- e pass9: <INTEL SSDSC2KG240G7 SCV10100> ACS-3 ATA SATA 3.x device pass9: 600.000MB/s transfers, Command Queueing Enabled Security Option Value supported yes enabled no drive locked no security config frozen no count expired no security level high enhanced erase supported yes erase time 4 min enhanced erase time 4 min master password rev fffe
The problem:
Code:
root@freenas:~ # camcontrol hpa da7 -s 31250000 pass8: <INTEL SSDSC2KG240G7 SCV10100> ACS-3 ATA SATA 3.x device pass8: 600.000MB/s transfers, Command Queueing Enabled camcontrol: HPA is not supported by this device root@freenas:~ # camcontrol hpa da8 -s 31250000 pass9: <INTEL SSDSC2KG240G7 SCV10100> ACS-3 ATA SATA 3.x device pass9: 600.000MB/s transfers, Command Queueing Enabled camcontrol: HPA is not supported by this device
Any ideas how I can get these drives to be 16GB? Or is HPA really not supported?...
