Greeetings! I have 2 10-disk raidz2 setups using 1.5TB HDDs. This makes for 2 10.6TB shares. One set only has 6GB available. The other set has over 550GB available, and I am unable to move more files onto it. It will move maybe 200MB, and then say the share is not available. If I skip that file, it just does it again with the next one. I am running the following:
FreeNAS 8.0.3 Release
Gigabyte MA785G-UD3H 1.0 Motherboard
4.0 GB DDR2 RAM
Kingston 2GB Thumbdrive
20 1.5TB HDDs
Norco RPC-4220
Antec True 430 PSU
Intel PWLA8391GT 10/100/1000 NIC
2x Intel SASUC8I Add-On Cards
I thought it might have been the ethernet connection, so I went from using the onboard one to an Intel NIC, the Intel PWLA8391GT. Keeping in mind this a PCI card, I also have another one of these in use on my other FreeNAS box with 10x 2TB HDDs in raidz2, but there are no network problems there.
Also, upon further inspection, I have two drives I recently replaced. In the gpart list for the two drives, the "Mode" is different. One drive has the same modes as the other drives in the pool, one does not.
The drive set is the following disks:
ada1
ada3
da2
da3
da6
da7
da10
da11
da14
da15
All the disks but da15 are as follows:
Geom name: ada3
state: OK
fwheads: 16
fwsectors: 63
last: 2930277134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada3p1
Mediasize: 2147483648 (2.0G)
Sectorsize: 512
Mode: r1w1e0
rawuuid: 009ca11c-38de-11e1-ad6c-001b21cbcfe9
rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 2147483648
offset: 65536
type: freebsd-swap
index: 1
end: 4194431
start: 128
2. Name: ada3p2
Mediasize: 1498154343936 (1.4T)
Sectorsize: 512
Mode: r1w1e1
rawuuid: 00ad2f39-38de-11e1-ad6c-001b21cbcfe9
rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 1498154343936
offset: 2147549184
type: freebsd-zfs
index: 2
end: 2930277134
start: 4194432
Consumers:
1. Name: ada3
Mediasize: 1500301910016 (1.4T)
Sectorsize: 512
Mode: r2w2e3
The drive which is different is as follows:
Geom name: da15
state: OK
fwheads: 255
fwsectors: 63
last: 2930277134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: da15p1
Mediasize: 2147483648 (2.0G)
Sectorsize: 512
Mode: r0w0e0
rawuuid: 4ab8779c-3a6b-11e1-9ff7-001b21cbcfe9
rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 2147483648
offset: 65536
type: freebsd-swap
index: 1
end: 4194431
start: 128
2. Name: da15p2
Mediasize: 1498154343936 (1.4T)
Sectorsize: 512
Mode: r1w1e1
rawuuid: 5bb7f570-3a6b-11e1-9ff7-001b21cbcfe9
rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 1498154343936
offset: 2147549184
type: freebsd-zfs
index: 2
end: 2930277134
start: 4194432
Consumers:
1. Name: da15
Mediasize: 1500301910016 (1.4T)
Sectorsize: 512
Mode: r1w1e2
I do not understand the difference in the modes, nor do I know how to change them so they all match. I also do not know if it even makes a difference. Also, I recently replaced two drives, one through the GUI (the modes match the rest of the set), and the other through the CLI (modes do not match). Thoughts, anyone?
FreeNAS 8.0.3 Release
Gigabyte MA785G-UD3H 1.0 Motherboard
4.0 GB DDR2 RAM
Kingston 2GB Thumbdrive
20 1.5TB HDDs
Norco RPC-4220
Antec True 430 PSU
Intel PWLA8391GT 10/100/1000 NIC
2x Intel SASUC8I Add-On Cards
I thought it might have been the ethernet connection, so I went from using the onboard one to an Intel NIC, the Intel PWLA8391GT. Keeping in mind this a PCI card, I also have another one of these in use on my other FreeNAS box with 10x 2TB HDDs in raidz2, but there are no network problems there.
Also, upon further inspection, I have two drives I recently replaced. In the gpart list for the two drives, the "Mode" is different. One drive has the same modes as the other drives in the pool, one does not.
The drive set is the following disks:
ada1
ada3
da2
da3
da6
da7
da10
da11
da14
da15
All the disks but da15 are as follows:
Geom name: ada3
state: OK
fwheads: 16
fwsectors: 63
last: 2930277134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada3p1
Mediasize: 2147483648 (2.0G)
Sectorsize: 512
Mode: r1w1e0
rawuuid: 009ca11c-38de-11e1-ad6c-001b21cbcfe9
rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 2147483648
offset: 65536
type: freebsd-swap
index: 1
end: 4194431
start: 128
2. Name: ada3p2
Mediasize: 1498154343936 (1.4T)
Sectorsize: 512
Mode: r1w1e1
rawuuid: 00ad2f39-38de-11e1-ad6c-001b21cbcfe9
rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 1498154343936
offset: 2147549184
type: freebsd-zfs
index: 2
end: 2930277134
start: 4194432
Consumers:
1. Name: ada3
Mediasize: 1500301910016 (1.4T)
Sectorsize: 512
Mode: r2w2e3
The drive which is different is as follows:
Geom name: da15
state: OK
fwheads: 255
fwsectors: 63
last: 2930277134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: da15p1
Mediasize: 2147483648 (2.0G)
Sectorsize: 512
Mode: r0w0e0
rawuuid: 4ab8779c-3a6b-11e1-9ff7-001b21cbcfe9
rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 2147483648
offset: 65536
type: freebsd-swap
index: 1
end: 4194431
start: 128
2. Name: da15p2
Mediasize: 1498154343936 (1.4T)
Sectorsize: 512
Mode: r1w1e1
rawuuid: 5bb7f570-3a6b-11e1-9ff7-001b21cbcfe9
rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
label: (null)
length: 1498154343936
offset: 2147549184
type: freebsd-zfs
index: 2
end: 2930277134
start: 4194432
Consumers:
1. Name: da15
Mediasize: 1500301910016 (1.4T)
Sectorsize: 512
Mode: r1w1e2
I do not understand the difference in the modes, nor do I know how to change them so they all match. I also do not know if it even makes a difference. Also, I recently replaced two drives, one through the GUI (the modes match the rest of the set), and the other through the CLI (modes do not match). Thoughts, anyone?
