dash
Dabbler
- Joined
- Jul 9, 2015
- Messages
- 10
Been getting SMART errors on my console. Seen drives fail, but given the life of this drive I am a little surprised. Drive is 5+ years old. NAS has been mostly turn/off as use. Recently moved it into a new case and keeping it on 24/7.
Looking at similar posts and see that most people with this error are showing where the `LBA_of_first_error` is and can tell the drive to stop using the sectors or that their drive is hosed. Hoping someone could shed a little light on my error since its showing blank. Assuming the drive is hitting unreadable sectores and failing the scan. I am going to have to replace the drive. but if I can avoid shelling out ~$250 for a new one I would like to.
Code:
May 20 16:00:05 freenas smartd[17511]: Device: /dev/ada1, 384 Currently unreadable (pending) sectors May 20 16:00:05 freenas smartd[17511]: Device: /dev/ada1, 384 Offline uncorrectable sectors
Looking at similar posts and see that most people with this error are showing where the `LBA_of_first_error` is and can tell the drive to stop using the sectors or that their drive is hosed. Hoping someone could shed a little light on my error since its showing blank. Assuming the drive is hitting unreadable sectores and failing the scan. I am going to have to replace the drive. but if I can avoid shelling out ~$250 for a new one I would like to.
Code:
smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p7 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Archive HDD
Device Model: ST8000AS0002-1NA17Z
Serial Number: Z840AKWB
LU WWN Device Id: 5 000c50 087451193
Firmware Version: AR15
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed May 20 16:29:56 2020 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 966) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30a5) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 120 088 006 Pre-fail Always - 243927232
3 Spin_Up_Time 0x0003 091 090 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 53
5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 1344
7 Seek_Error_Rate 0x000f 074 060 030 Pre-fail Always - 34564692991
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2600
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 51
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 090 090 000 Old_age Always - 10
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 73015558161
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 064 060 045 Old_age Always - 36 (Min/Max 22/37)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 102
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 147
194 Temperature_Celsius 0x0022 036 040 000 Old_age Always - 36 (0 19 0 0 0)
195 Hardware_ECC_Recovered 0x001a 120 099 000 Old_age Always - 243927232
197 Current_Pending_Sector 0x0012 099 099 000 Old_age Always - 384
198 Offline_Uncorrectable 0x0010 099 099 000 Old_age Offline - 384
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 2595 (15 227 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 7237368292
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 166220301821
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 2492 hours (103 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 3d+08:29:50.017 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:50.016 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:50.016 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 3d+08:29:49.954 READ LOG EXT
60 00 08 ff ff ff 4f 00 3d+08:29:47.007 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 2492 hours (103 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 3d+08:29:47.007 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:47.007 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:47.006 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:47.006 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 3d+08:29:46.933 READ LOG EXT
Error 8 occurred at disk power-on lifetime: 2492 hours (103 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 3d+08:29:44.084 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:44.005 READ FPDMA QUEUED
61 00 28 ff ff ff 4f 00 3d+08:29:44.004 WRITE FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:44.004 READ FPDMA QUEUED
61 00 40 ff ff ff 4f 00 3d+08:29:44.004 WRITE FPDMA QUEUED
Error 7 occurred at disk power-on lifetime: 2492 hours (103 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 3d+08:29:40.936 READ FPDMA QUEUED
61 00 30 ff ff ff 4f 00 3d+08:29:40.924 WRITE FPDMA QUEUED
61 00 00 ff ff ff 4f 00 3d+08:29:40.924 WRITE FPDMA QUEUED
61 00 b0 ff ff ff 4f 00 3d+08:29:40.923 WRITE FPDMA QUEUED
61 00 78 ff ff ff 4f 00 3d+08:29:40.923 WRITE FPDMA QUEUED
Error 6 occurred at disk power-on lifetime: 2492 hours (103 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 3d+08:29:37.453 READ FPDMA QUEUED
61 00 08 ff ff ff 4f 00 3d+08:29:37.453 WRITE FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:37.205 READ FPDMA QUEUED
60 00 10 ff ff ff 4f 00 3d+08:29:37.199 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:29:36.992 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 20% 2330 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Code:
pool: storage
state: ONLINE
status: Some supported features are not enabled on the pool. The pool can
still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 264K in 0 days 00:00:03 with 0 errors on Sat May 16 04:30:04 2020
config:
NAME STATE READ WRITE CKSUM
storage ONLINE 0 0 0
raidz2-0 ONLINE 0 0 0
gptid/701b325b-3fd5-11e6-a190-00259031c250 ONLINE 0 0 0
ada1p2 ONLINE 0 0 0
gptid/71dc6ac6-3fd5-11e6-a190-00259031c250 ONLINE 0 0 0
gptid/72ba9a86-3fd5-11e6-a190-00259031c250 ONLINE 0 0 0
errors: No known data errors
