Hello All,
I've been doing a LOT of reading and research and have finally put together the components for a FreeNAS server. I'd appreciate any advice and feedback from the FreeNAS Brain Trust. :)
My plan is to build a FreeNAS server for home media (movies, music, photos, etc) as well as system backup images, backups of software code (I'm a software developer) and general file sharing.
Data integrity and reliability is the most important priority followed by storage capacity & performance. I'd like a very quiet system as this will be housed in my home office. I'm also keeping an eye toward future expansion (mainly adding more hard drives).
I plan to build a RAIDZ2 with six 3TB WD Red drives for a total capacity of ~12TB (minus overhead).
Motherboard
Video
Case
Any thoughts are most appreciated.
I'd like to add that these forums are a gold mine of information for learning about FreeNAS. I've learned so much from the friendly folks here, especially those that write the "pinned" posts. So, BIG THANKS to all of you who take the time to help us newbies!!
Peter
I've been doing a LOT of reading and research and have finally put together the components for a FreeNAS server. I'd appreciate any advice and feedback from the FreeNAS Brain Trust. :)
My plan is to build a FreeNAS server for home media (movies, music, photos, etc) as well as system backup images, backups of software code (I'm a software developer) and general file sharing.
Data integrity and reliability is the most important priority followed by storage capacity & performance. I'd like a very quiet system as this will be housed in my home office. I'm also keeping an eye toward future expansion (mainly adding more hard drives).
I plan to build a RAIDZ2 with six 3TB WD Red drives for a total capacity of ~12TB (minus overhead).
Motherboard
- SuperMicro X10SL7-F
- SuperMicro X10SLL+-F
- Essentially these two boards are the same except that the SL7 provides 8 SAS ports. Each of these boards has 6 SATA ports which will work fine for my number of drives. From my reading in the various posts, I understand I could attach a Sata hard drive to a SAS port. However, is this as simple as connecting a Sata drive to a regular Sata port? Or is there a lot of adapters, configuration and hassle with getting a Sata drive to work in a SAS port? If it's fairly straightforward (and reliable!), then I'd opt for the SL-7 and use the SAS ports to add more drives later. If not, then I'd go with the SLL+-F and add an HBA Sata card later for drive expansion. Thoughts?
- Crucial 16GB (2 x 8GB) 240-Pin DDR3 SDRAM ECC Unbuffered DDR3 1600 (PC3 12800) Server Memory Model CT2KIT102472BD160B (1.35V) OR
- Crucial 16GB (2 x 8GB) 240-Pin DDR3 SDRAM ECC Unbuffered DDR3 1600 (PC3 12800) Server Memory Model CT2KIT102472BA160B (1.5V)
- Does it matter regarding voltage - 1.5v versus 1.35. If not, I'd just go with the cheaper of the two.
Video
- Since it's a server, I'm just using the integrated graphics on the board/processor.
Case
- Fractal Design Define R5
- Western Digital 3TB Red NAS drives (x6)
- I've been reading that many folks are moving to use an SSD (or two) as the boot drive since the lower capacity SSD prices are fairly inexpensive now. However, I already have any and all makes/models/capacities of USB sticks. I was going just use two of my newer 16GB Kingston or SanDisk USB sticks.
- Does it matter to use USB 3 vs. USB 2. I'm thinking it shouldn't much matter since FreeNAS loads the entire O/S image into memory upon boot. USB2 would just take a bit longer to boot. Is this correct?
Any thoughts are most appreciated.
I'd like to add that these forums are a gold mine of information for learning about FreeNAS. I've learned so much from the friendly folks here, especially those that write the "pinned" posts. So, BIG THANKS to all of you who take the time to help us newbies!!
Peter