Hi
I had to replace something with a ram and after I replaced, suddenly one of my disks was having problems !!
Can a Ram replacement do something like this?
I connected the drive to another computer (windows) and checked with crystaldiskinfo and everything was fine. I have had these drives for less than a year (WD Rad 3TB)
I have these errors:
smart test ada1
And before that I had a problem that he even got the drive out of Pool but Narrally just have problems with drives that fail in encrypted pool so he didn't return it Finally I removed the pool from FreeNAS and did import it then the drive came back but with the errors shown above.
Is this a cable problem? Or the drive? I do not know what to do!!! help!
I had to replace something with a ram and after I replaced, suddenly one of my disks was having problems !!
Can a Ram replacement do something like this?
I connected the drive to another computer (windows) and checked with crystaldiskinfo and everything was fine. I have had these drives for less than a year (WD Rad 3TB)
I have these errors:
Code:
# zpool status
pool: NAS
state: DEGRADED
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are unaffected.
action: Determine if the device needs to be replaced, and clear the errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: http://illumos.org/msg/ZFS-8000-9P
scan: scrub in progress since Fri Jan 24 17:45:42 2020
887G scanned at 424M/s, 262G issued at 125M/s, 6.43T total
0 repaired, 3.97% done, 0 days 14:22:41 to go
config:
NAME STATE READ WRITE CKSUM
NAS DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
gptid/a79fe0a8-3c43-11e9-b8f1-e069952bbf5c.eli DEGRADED 0 0 71 too many errors
gptid/a87765fc-3c43-11e9-b8f1-e069952bbf5c.eli ONLINE 0 0 0
gptid/a9463a8e-3c43-11e9-b8f1-e069952bbf5c.eli ONLINE 0 0 0
errors: No known data errorssmart test ada1
Code:
# smartctl -a /dev/ada1
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68N32N0
Serial Number: WD-WCC7K1FU80RF
LU WWN Device Id: 5 0014ee 20fbb11e3
Firmware Version: 82.00A82
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Jan 24 18:22:29 2020 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 241) Self-test routine in progress...
10% of test remaining.
Total time to complete Offline
data collection: (31200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 332) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 157 156 021 Pre-fail Always - 7133
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 29
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7796
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 29
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 6
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 33
194 Temperature_Celsius 0x0022 116 104 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 198 000 Old_age Always - 13
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6364 -
# 2 Short offline Completed without error 00% 4929 -
# 3 Short offline Completed without error 00% 3443 -
# 4 Extended offline Completed without error 00% 3218 -
# 5 Short offline Completed without error 00% 1981 -
# 6 Short offline Completed without error 00% 580 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
And before that I had a problem that he even got the drive out of Pool but Narrally just have problems with drives that fail in encrypted pool so he didn't return it Finally I removed the pool from FreeNAS and did import it then the drive came back but with the errors shown above.
Is this a cable problem? Or the drive? I do not know what to do!!! help!
