I managed to get the SAS6/iR flashed to IT mode.
For comparison, here's the output of
smartctl -x after the flash:
/dev/da0
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p31 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: SEAGATE
Product: ST3400755SS
Revision: NS25
User Capacity: 400,000,000,000 bytes [400 GB]
Logical block size: 512 bytes
Rotation Rate: 10033 rpm
Logical Unit id: 0x5000c5000357e6d3
Serial number: 3RJ0HS2S
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Feb 24 17:33:30 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 26 C
Drive Trip Temperature: 68 C
Elements in grown defect list: 0
Vendor (Seagate) cache information
Blocks sent to initiator = 1651494778
Blocks received from initiator = 4091358526
Blocks read from cache and sent to initiator = 1120181778
Number of read and write commands whose size <= segment size = 424270760
Number of read and write commands whose size > segment size = 58174175
Vendor (Seagate/Hitachi) factory information
number of hours powered up = 52455.03
number of minutes until next internal SMART test = 52
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 3260438328 3 0 3260438331 3260438331 569216.177 0
write: 0 0 0 0 0 120869.542 0
verify: 567144053 0 0 567144053 567144053 106594.624 0
Non-medium error count: 4208
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 52407 - [- - -]
# 2 Background long Completed - 1 - [- - -]
# 3 Background short Completed - 0 - [- - -]
Long (extended) Self Test duration: 5626 seconds [93.8 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52455:03 [3147303 minutes]
Number of background scans performed: 316, scan progress: 9.11%
Number of background medium scans performed: 0
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357e6d1
attached SAS address = 0x50022190c5175800
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357e6d2
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
/dev/da1
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p31 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: SEAGATE
Product: ST3400755SS
Revision: NS25
User Capacity: 400,000,000,000 bytes [400 GB]
Logical block size: 512 bytes
Rotation Rate: 10033 rpm
Logical Unit id: 0x5000c5000357f8c7
Serial number: 3RJ0JDCD
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Feb 24 17:33:40 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 26 C
Drive Trip Temperature: 68 C
Elements in grown defect list: 0
Vendor (Seagate) cache information
Blocks sent to initiator = 1722457659
Blocks received from initiator = 3646264930
Blocks read from cache and sent to initiator = 891013300
Number of read and write commands whose size <= segment size = 2965196311
Number of read and write commands whose size > segment size = 60272260
Vendor (Seagate/Hitachi) factory information
number of hours powered up = 53601.17
number of minutes until next internal SMART test = 52
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 307054890 0 0 307054890 307054890 151465.907 0
write: 0 0 0 0 0 98652.595 0
verify: 159004248 0 0 159004248 159004248 110114.647 0
Non-medium error count: 25
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 53553 - [- - -]
# 2 Background long Completed - 2 - [- - -]
# 3 Background short Completed - 0 - [- - -]
Long (extended) Self Test duration: 5626 seconds [93.8 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 53601:10 [3216070 minutes]
Number of background scans performed: 318, scan progress: 9.33%
Number of background medium scans performed: 0
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357f8c5
attached SAS address = 0x50022190c5175801
attached phy identifier = 1
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357f8c6
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
/dev/da2
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p31 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: SEAGATE
Product: ST3400755SS
Revision: NS25
User Capacity: 400,000,000,000 bytes [400 GB]
Logical block size: 512 bytes
Rotation Rate: 10033 rpm
Logical Unit id: 0x5000c5000357e9d7
Serial number: 3RJ0HH1J
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Feb 24 17:33:50 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 26 C
Drive Trip Temperature: 68 C
Elements in grown defect list: 3
Vendor (Seagate) cache information
Blocks sent to initiator = 4210376088
Blocks received from initiator = 2897113491
Blocks read from cache and sent to initiator = 4052089939
Number of read and write commands whose size <= segment size = 2950102190
Number of read and write commands whose size > segment size = 60272260
Vendor (Seagate/Hitachi) factory information
number of hours powered up = 54215.78
number of minutes until next internal SMART test = 52
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 684297382 6 0 684297388 684297388 150134.694 0
write: 0 0 5 5 5 98269.044 0
verify: 306616577 2 0 306616579 306616579 110271.628 0
Non-medium error count: 124947
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 54168 - [- - -]
# 2 Background long Completed - 2 - [- - -]
# 3 Background short Completed - 0 - [- - -]
Long (extended) Self Test duration: 5626 seconds [93.8 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 54215:47 [3252947 minutes]
Number of background scans performed: 323, scan progress: 9.17%
Number of background medium scans performed: 0
# when lba(hex) [sk,asc,ascq] reassign_status
1 40000:17 0000000003e6c5df [1,17,1] Recovered via rewrite in-place
2 40170:35 0000000003e6c5df [1,17,1] Recovered via rewrite in-place
3 41021:59 0000000003e6c5df [1,17,3] Recovered via rewrite in-place
4 46476:17 000000000b9d7aa1 [1,17,3] Successfully reassigned
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357e9d5
attached SAS address = 0x50022190c5175802
attached phy identifier = 2
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357e9d6
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
/dev/da3
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p31 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: SEAGATE
Product: ST3400755SS
Revision: NS25
User Capacity: 400,000,000,000 bytes [400 GB]
Logical block size: 512 bytes
Rotation Rate: 10033 rpm
Logical Unit id: 0x5000c5000357fba7
Serial number: 3RJ0JDGG
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Wed Feb 24 17:34:05 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 25 C
Drive Trip Temperature: 68 C
Elements in grown defect list: 0
Vendor (Seagate) cache information
Blocks sent to initiator = 123966676
Blocks received from initiator = 63556612
Blocks read from cache and sent to initiator = 2568483031
Number of read and write commands whose size <= segment size = 261420356
Number of read and write commands whose size > segment size = 58174175
Vendor (Seagate/Hitachi) factory information
number of hours powered up = 52435.58
number of minutes until next internal SMART test = 52
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 984426416 37 0 984426453 984426453 564065.972 0
write: 0 0 0 0 0 118807.254 0
verify: 1082282375 0 0 1082282375 1082282375 106788.016 0
Non-medium error count: 12696
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Completed - 52388 - [- - -]
# 2 Background long Completed - 1 - [- - -]
# 3 Background short Completed - 0 - [- - -]
Long (extended) Self Test duration: 5626 seconds [93.8 minutes]
Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 52435:35 [3146135 minutes]
Number of background scans performed: 316, scan progress: 9.63%
Number of background medium scans performed: 0
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357fba5
attached SAS address = 0x50022190c5175803
attached phy identifier = 3
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5000357fba6
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
/dev/da4
Code:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p31 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda ES
Device Model: ST3750640NS
Serial Number: 5QD2GC07
LU WWN Device Id: 5 000c50 0028d7f48
Firmware Version: 3BKH
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Wed Feb 24 17:34:15 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Unexpected SCT status 0xffff (action_code=4, function_code=2)
Wt Cache Reorder: Unknown (SCT Feature Control command failed)
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 221) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 111 085 006 - 35454658
3 Spin_Up_Time PO---- 095 091 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 289
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1
7 Seek_Error_Rate POSR-- 065 060 030 - 171933536023
9 Power_On_Hours -O--CK 035 035 000 - 57813
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 160
187 Reported_Uncorrect -O--CK 100 100 000 - 0
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 072 032 045 Past 28 (1 102 28 23 0)
194 Temperature_Celsius -O---K 028 068 000 - 28 (0 21 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 093 057 000 - 49259086
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xff GPL - 23040 Reserved
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 57767 -
# 2 Conveyance offline Completed without error 00% 57764 -
# 3 Extended offline Completed without error 00% 7 -
# 4 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 521 (0x0209)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Max Temperature: 28 Celsius
Lifetime Max Temperature: 68 Celsius
Another SCT command is executing, abort Read Data Table
(SCT ext_status_code 0xffff, action_code=4, function_code=2)
Read SCT Temperature History failed
Another SCT command is executing, abort Error Recovery Control
(SCT ext_status_code 0xffff, action_code=4, function_code=2)
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
Hit character limit, continuing in a new post.