After replacing a Disk all other disks are shown as degraded except the replacement is this normal?

[Ganzir]

OK, I just deleted all corrupt files. When I do a

Code:

zpool status -v

now I get the following result:

Code:

root@freenas:~ # zpool status -v
  pool: freenas-boot
state: ONLINE
  scan: scrub repaired 0 in 0h0m with 0 errors on Mon Jul 27 03:45:03 2020
config:

        NAME        STATE     READ WRITE CKSUM
        freenas-boot  ONLINE       0     0     0
          nvd0p2    ONLINE       0     0     0

errors: No known data errors

  pool: mypool
state: DEGRADED
status: One or more devices is currently being resilvered.  The pool will
        continue to function, possibly in a degraded state.
action: Wait for the resilver to complete.
  scan: resilver in progress since Mon Aug 24 21:30:31 2020
        293G scanned out of 3.41T at 311M/s, 2h55m to go
        73.3G resilvered, 8.39% done
config:

        NAME                                            STATE     READ WRITE CKSUM
        mypool                             DEGRADED     0     0   550
          raidz1-0                                      DEGRADED     0     0 2.15K
            gptid/d81e36b2-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     2  too many errors  (resilvering)
            gptid/d8d85c83-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors
            gptid/c20e79a0-e4a8-11ea-9166-10c37b4dfcfa  ONLINE       0     0     0  (resilvering)
            gptid/da72f949-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors

errors: Permanent errors have been detected in the following files:

        mypool/windowsshare:<0x0>
        mypool/windowsshare:<0x82a02>
        mypool/windowsshare:<0x82806>
        mypool/windowsshare:<0x82a0f>
        mypool/windowsshare:<0x8281b>
        mypool/windowsshare:<0x82921>
        mypool/windowsshare:<0x82a2e>
        mypool/windowsshare:<0x82833>
        mypool/windowsshare:<0x8283a>
        mypool/windowsshare:<0x82841>
        mypool/windowsshare:<0x82941>
        mypool/windowsshare:<0x82947>
        mypool/windowsshare:<0x82848>
        mypool/windowsshare:<0x8294e>
        mypool/windowsshare:<0x8284f>
        mypool/windowsshare:<0x82856>
        mypool/windowsshare:<0x8285d>
        mypool/windowsshare:<0x82864>
        mypool/windowsshare:<0x8276c>
        mypool/windowsshare:<0x82a73>
        mypool/windowsshare:<0x82875>
        mypool/windowsshare:<0x8277c>
        mypool/windowsshare:<0x8297d>
        mypool/windowsshare:<0x82786>
        mypool/windowsshare:<0x82887>
        mypool/windowsshare:<0x8278d>
        mypool/windowsshare:<0x8288e>
        mypool/windowsshare:<0x82794>
        mypool/windowsshare:<0x8279b>
        mypool/windowsshare:<0x82a9b>
        mypool/windowsshare:<0x81f9c>
        mypool/windowsshare:<0x829a1>
        mypool/windowsshare:<0x827a2>
        mypool/windowsshare:<0x82aa5>
        mypool/windowsshare:<0x829a8>
        mypool/windowsshare:<0x82ab8>
        mypool/windowsshare:<0x827ba>
        mypool/windowsshare:<0x829bf>
        mypool/windowsshare:<0x495bf>
        mypool/windowsshare:<0x827c1>
        mypool/windowsshare:<0x828c7>
        mypool/windowsshare:<0x82ac7>
        mypool/windowsshare:<0x827c8>
        mypool/windowsshare:<0x827cf>
        mypool/windowsshare:<0x827d6>
        mypool/windowsshare:<0x829d7>
        mypool/windowsshare:<0x827dd>

As you may have noticed the system is resilvering again, it started this process on its own - I do not know what triggered it - I will keep you updated once it is finished.

Regarding the RAM: Well I spent about 60 EUR on 16 GB, that does not hurt too much and doubles the NAS' RAM capacity, so I think it's a good thing.

I will test the RAM from the NAS in another System just to get clarity about possible reasons for those errors, this however will take some time, since I do not have immediate access to another System that run with DDR3.

Thanks so far and kind regards.

 

[Yorick]

What started the resilver this time are checksum errors on gptid/d81e36b2-1a9a-11e6-b0c5-10c37b4dfcfa, I think. You can use "geom PART list" to find out which drive has that partition ID.

 

[Ganzir]

Resilvering completed last night, here are the results:

Code:

root@freenas:~ # zpool status -v
  pool: freenas-boot
 state: ONLINE
  scan: scrub repaired 0 in 0h0m with 0 errors on Mon Jul 27 03:45:03 2020
config:

        NAME        STATE     READ WRITE CKSUM
        freenas-boot  ONLINE       0     0     0
          nvd0p2    ONLINE       0     0     0

errors: No known data errors

  pool: mypool
 state: DEGRADED
status: One or more devices has experienced an error resulting in data
        corruption.  Applications may be affected.
action: Restore the file in question if possible.  Otherwise restore the
        entire pool from backup.
   see: http://illumos.org/msg/ZFS-8000-8A
  scan: resilvered 872G in 3h23m with 4 errors on Tue Aug 25 00:53:49 2020
config:

        NAME                                            STATE     READ WRITE CKSUM
        mypool                             DEGRADED     0     0 6.76K
          raidz1-0                                      DEGRADED     0     0 27.1K
            gptid/d81e36b2-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0    20  too many errors
            gptid/d8d85c83-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors
            gptid/c20e79a0-e4a8-11ea-9166-10c37b4dfcfa  ONLINE       0     0     0
            gptid/da72f949-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors

errors: Permanent errors have been detected in the following files:

        mypool/windowsshare:<0x0>
        mypool/windowsshare:<0x827ff>

I will start a scrubbing, maybe I can get rid of those remaining two errors.

"geom PART list"

gives me:

Code:

root@freenas:~ # geom PART list
Geom name: nvd0
modified: false
state: OK
fwheads: 255
fwsectors: 63
last: 250069646
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: nvd0p1
   Mediasize: 524288 (512K)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 17408
   Mode: r0w0e0
   rawuuid: cd609f50-13e7-11e6-8aac-10c37b4dfcfa
   rawtype: 21686148-6449-6e6f-744e-656564454649
   label: (null)
   length: 524288
   offset: 17408
   type: bios-boot
   index: 1
   end: 1057
   start: 34
2. Name: nvd0p2
   Mediasize: 128035110912 (119G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 544768
   Mode: r1w1e1
   rawuuid: cd61ce43-13e7-11e6-8aac-10c37b4dfcfa
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 128035110912
   offset: 544768
   type: freebsd-zfs
   index: 2
   end: 250069639
   start: 1064
Consumers:
1. Name: nvd0
   Mediasize: 128035676160 (119G)
   Sectorsize: 512
   Mode: r1w1e2

Geom name: ada0
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada0p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: d8121a92-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada0p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r1w1e2
   rawuuid: d81e36b2-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada0
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r2w2e5

Geom name: ada1
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada1p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: d8ca92ca-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada1p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r1w1e2
   rawuuid: d8d85c83-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada1
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r2w2e5

Geom name: ada2
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 15628053127
first: 40
entries: 152
scheme: GPT
Providers:
1. Name: ada2p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e1
   rawuuid: c2066037-e4a8-11ea-9166-10c37b4dfcfa
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada2p2
   Mediasize: 7999415648256 (7.3T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r1w1e2
   rawuuid: c20e79a0-e4a8-11ea-9166-10c37b4dfcfa
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 7999415648256
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 15628053119
   start: 4194432
Consumers:
1. Name: ada2
   Mediasize: 8001563222016 (7.3T)
   Sectorsize: 512
   Stripesize: 4096
   Stripeoffset: 0
   Mode: r2w2e5

Geom name: ada3
modified: false
state: OK
fwheads: 16
fwsectors: 63
last: 3907029134
first: 34
entries: 128
scheme: GPT
Providers:
1. Name: ada3p1
   Mediasize: 2147483648 (2.0G)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 65536
   Mode: r1w1e1
   rawuuid: da66ec5b-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cb5-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 2147483648
   offset: 65536
   type: freebsd-swap
   index: 1
   end: 4194431
   start: 128
2. Name: ada3p2
   Mediasize: 1998251364352 (1.8T)
   Sectorsize: 512
   Stripesize: 0
   Stripeoffset: 2147549184
   Mode: r1w1e2
   rawuuid: da72f949-1a9a-11e6-b0c5-10c37b4dfcfa
   rawtype: 516e7cba-6ecf-11d6-8ff8-00022d09712b
   label: (null)
   length: 1998251364352
   offset: 2147549184
   type: freebsd-zfs
   index: 2
   end: 3907029127
   start: 4194432
Consumers:
1. Name: ada3
   Mediasize: 2000398934016 (1.8T)
   Sectorsize: 512
   Mode: r2w2e5

I does not tell me that much since the rawuuid ending in fcfa is shown for every drive.

I keep you updated once the scrub finishes.

 

[Yorick]

Looks like ada0. It’s the beginning of the Gptid that varies, not the end. Since that’s the only drive with checksum errors, if I read this right at least, and smart doesn’t indicate it failing, maybe take a look at its cable and port. You could power FreeNAS down and swap out the cable just to be sure. If you have a free SATA port, maybe move it to that at the same time. It’s drive designation may change then but its gptid won’t.

speaking of: How are these drives connected? To motherboard SATA ports, or to an add-in card? If the latter, what kind?

What still gets me is that a single error wouldn’t cause corruption. It’s got to be two at least for any given entry, since you have single parity.

And we still don’t know what in the system is causing that.

 

[Ganzir]

I am using the following Mainboard:

H97i-Plus from Asus

The drives are connected directly to the Mainboard which only has 4 SATA ports, so it is not possible to switch to another port.

The new RAM is arriving today so I can switch the RAM at least. ... I could try new cables as well, a question in this regard: Does i matter which HDD is connected to which SATA-Port?

Assuming ada0 is connected to SATA0, ada1 is sconnected to SATA1 and so forth, when I replace the cables and be some 'mistake' connect ada0 to SATA1, will that mess up the pool or doen't it matter which drive is connected to which port?

Kind Regards

 

[Yorick]

Does i matter which HDD is connected to which SATA-Port?

No it does not. FreeNAS uses gptids for this reason, so it doesn’t matter which port a drive is connected to.
The only way to figure out what drive “ada0” refers to, by the way, is by serial number. Don’t go by port number, that might not match.

 

[Ganzir]

OK that is great to know, so when I replace a disk in the future I simply look for the serial number and reconnect everything as I see fit.

When I replaced the last drive I took the utmost care to connect everything exactly in the same way. - Good to know that this is not necessary.

EDIT: Somewhat offtopic: I have 8 SSD lying around, is it advisable to use SSDs to build an all flash NAS or are there any drawbacks?

EDIT2: Here are the resulte of today's scrub:

Code:

root@freenas:~ # zpool status -v
  pool: freenas-boot
state: ONLINE
  scan: scrub repaired 0 in 0h0m with 0 errors on Mon Jul 27 03:45:03 2020
config:

        NAME        STATE     READ WRITE CKSUM
        freenas-boot  ONLINE       0     0     0
          nvd0p2    ONLINE       0     0     0

errors: No known data errors

  pool: mypool
state: DEGRADED
status: One or more devices has experienced an error resulting in data
        corruption.  Applications may be affected.
action: Restore the file in question if possible.  Otherwise restore the
        entire pool from backup.
   see: http://illumos.org/msg/ZFS-8000-8A
  scan: scrub repaired 572K in 3h11m with 4 errors on Tue Aug 25 11:11:06 2020
config:

        NAME                                            STATE     READ WRITE CKSUM
        mypool                             DEGRADED     0     0 13.2K
          raidz1-0                                      DEGRADED     0     0 52.8K
            gptid/d81e36b2-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0    33  too many errors
            gptid/d8d85c83-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors
            gptid/c20e79a0-e4a8-11ea-9166-10c37b4dfcfa  ONLINE       0     0     0
            gptid/da72f949-1a9a-11e6-b0c5-10c37b4dfcfa  DEGRADED     0     0     0  too many errors

errors: Permanent errors have been detected in the following files:

        mypool/windowsshare:<0x0>
        mypool/windowsshare:<0x827ff>

So some errors remain. - That means the pool is permanently damaged, needs to be destroyed an rebuild?

 

[Yorick]

That means the pool is permanently damaged, needs to be destroyed an rebuild?

I believe so, yes. Did you ever find out what caused the errors in the first place?

Theoretically you could also rsync or send/recv everything in windowsshare into a new dataset, as much as it’ll let you, and then destroy windowsshare, and that should clear it.
Or destroy it, scrub, recreate it, and bring all data back in from backup.

I have 8 SSD lying around, is it advisable to use SSDs to build an all flash NAS or are there any drawbacks?

No drawbacks that I am aware of. Different thread for that use case maybe, though.

 

[Ganzir]

No I did not find out what causes those errors. I switched out the RAM-Modules, haven't been able to test the old ones yet.

Interesting thing is, that the System-Tab still tells me there are 8 GB of RAM although I have 16 installed.

I have been copying Data from the Share to other media, since of some Data I had no backups elsewhere. - This seemingly takes forever and maybe completes today.

Once this is finished I will update the FreeNAS to a current stable version and than recreate the share, and keep an eye on it regarding those errors.

Should they reappear the only possible option I can think of is, that the motherboard or CPU have been damaged somehow, in this case the NAS has died since I do not have the components to make any replacements. I'll keep you posted.

 

[jgreco]

Mmm. This doesn't look good.

Just to be clear, you've confirmed that the disks are not SMR disks? SMR disks are known to fail under the strain of a rebuild, though usually this also presents as other problems such as incredibly slow resilvering.

And this is not through something like an LSI HBA that could be overheating? That is one of the most common ways for bitspew to end up in a pool.

It would be very helpful if you would post a system manifest. The forum rules, conveniently linked at the top of every page in red, provide some guidelines for information that you should provide in order to make it easier to help you.

 

[Ganzir]

I have posted my system specification in post #7 of this thread.

There is no LSI HBA involved all drives are connected directly to the mainboard.

 

[Yorick]

that the System-Tab still tells me there are 8 GB of RAM although I have 16 installed.

The only way that can happen is if there's an issue with the RAM or the motherboard. Once your copy completes, it's worth figuring out whether a slot on the board is bad, check that the DIMMs are properly seated, and once you see all 16GB or have figured out why you don't, run a memtest86 or similar test on the new RAM. Yes your FreeNAS will be down for the duration: But if you can't trust your hardware, you can't use it meaningfully anyway.

 

[Ganzir]

OK my bad one of the DIMMs was not installed correctly, those slots on this ITX-Mobo are simply awkwardly to handle. Now all 16 GB show as they should. I updated the NAS to the most recent STABLE version (Version:FreeNAS-11.3-U4.1 ) I destroyed the pool and created a new one.

Here I encountered the issue that the NAS told me

Code:

Mixing disks of different sizes in a VDEV is not allowed

See first post in this thread for a picture.

However in my GUI there was a checkbox that said "force" so I checked this and could create the pool anyway.

Is this something that could backfire at a later date?

Added an SMB share and now could copy back the data. ... And yes before you beat me, I will test the old modules, this however would require me to occupy hardware that is in use elsewhere (monitor keyboard). So I will do so, when I am away for a weekend so memtest can run like 48+ hours. I hope some errors will turn up in the old RAM, otherwise the cause of error is up to everybodies best guess. Thanks again and I keep you posted.

EDIT: How oftern should I do scrubs / resilvering etc. ?
Where and how can I setup and most importantly test E-Mail-notifications in case something goes wrong in the future?

 

[Yorick]

Is this something that could backfire at a later date?

No. It's warning you because you won't get the full capacity of the larger drive, until all drives in the vdev have been replaced with larger ones. You know that, so choosing "force" to get past that warning is perfectly fine.

Scrub: I have mine set to a 35 day threshold. That way, they run every 5 weeks.

Email: System->EMail. Keep in mind that if you use 2FA with your email provider (which you really should), you'll need an "app password" for this alert email functionality.

 

[Ganzir]

OK thank you, I set mine to the same settings, so scrubbing will take place ever 35 days. I set up the E-Mail and send a Test-Mail which worked just fine.

So I guess this is it for now, I am copying back the data and I will test the old RAMs from 11th - 13th September, I am away for that weekend I do not need the machine that does the testing. This should give me a solid result to determine if something is wrong with those or not. Should the latter be the case I will keep an eye on the NAS because than the cause of error remains undetermined.

Thanks again for all your help and support so far.

EDIT: Just did a smartctl -x and got the feeling that the output is now significantly longer than previously.

For ada0:

Code:

smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital RE4-GP
Device Model:     WDC WD2003FYPS-27Y2B0
Serial Number:    WD-WCAVY5494816
LU WWN Device Id: 5 0014ee 25a518c8b
Firmware Version: 04.05G11
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Fri Sep  4 20:57:34 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 128
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (42900) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 488) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  3 Spin_Up_Time            POS--K   253   218   021    -    8891
  4 Start_Stop_Count        -O--CK   100   100   000    -    146
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   086   086   000    -    10525
 10 Spin_Retry_Count        -O--CK   100   100   000    -    0
 11 Calibration_Retry_Count -O--CK   100   100   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    146
192 Power-Off_Retract_Count -O--CK   200   200   000    -    23
193 Load_Cycle_Count        -O--CK   200   200   000    -    122
194 Temperature_Celsius     -O---K   116   100   000    -    36
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    23
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80       GPL     R/W  65535  Host vendor specific log
0x80       SL      R/W    255  Host vendor specific log
0x81-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb5  GPL,SL  VS       1  Device vendor specific log
0xb6       GPL     VS       1  Device vendor specific log
0xb7       GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      24  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 47 (device log contains only the most recent 24 errors)
        CR     = Command Register
        FEATR  = Features Register
        COUNT  = Count (was: Sector Count) Register
        LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
        LH     = LBA High (was: Cylinder High) Register    ]   LBA
        LM     = LBA Mid (was: Cylinder Low) Register      ] Register
        LL     = LBA Low (was: Sector Number) Register     ]
        DV     = Device (was: Device/Head) Register
        DC     = Device Control Register
        ER     = Error register
        ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 47 [22] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e7 7d cd 90 40 00  Error: IDNF at LBA = 0xe77dcd90 = 3883781520

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 60 00 00 e7 7d ea f8 40 08  2d+13:59:56.295  WRITE FPDMA QUEUED
  61 01 00 00 58 00 00 e7 7d e9 f8 40 08  2d+13:59:56.291  WRITE FPDMA QUEUED
  61 01 00 00 50 00 00 e7 7d e8 f8 40 08  2d+13:59:56.291  WRITE FPDMA QUEUED
  61 00 30 00 48 00 00 e7 7d e8 c8 40 08  2d+13:59:56.289  WRITE FPDMA QUEUED
  61 01 00 00 40 00 00 e7 7d e7 c8 40 08  2d+13:59:56.289  WRITE FPDMA QUEUED

Error 46 [21] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e1 a8 a2 e0 40 00  Error: IDNF at LBA = 0xe1a8a2e0 = 3785925344

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 b8 00 40 00 00 e1 a8 be 98 40 08  2d+13:47:13.686  WRITE FPDMA QUEUED
  61 01 00 00 38 00 00 e1 a8 bd 98 40 08  2d+13:47:13.683  WRITE FPDMA QUEUED
  61 01 00 00 30 00 00 e1 a8 bc 98 40 08  2d+13:47:13.680  WRITE FPDMA QUEUED
  61 01 00 00 28 00 00 e1 a8 bb 98 40 08  2d+13:47:13.678  WRITE FPDMA QUEUED
  61 01 00 00 20 00 00 e1 a8 ba 98 40 08  2d+13:47:13.677  WRITE FPDMA QUEUED

Error 45 [20] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e0 fd 60 c8 40 00  Error: IDNF at LBA = 0xe0fd60c8 = 3774701768

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 f0 00 00 da d9 2e d8 40 08  2d+13:43:34.068  WRITE FPDMA QUEUED
  61 01 00 00 60 00 00 da d9 2d d8 40 08  2d+13:43:34.066  WRITE FPDMA QUEUED
  61 00 08 00 e8 00 00 32 5f 30 f8 40 08  2d+13:43:34.063  WRITE FPDMA QUEUED
  61 00 10 00 e0 00 00 e3 6d a4 a8 40 08  2d+13:43:34.063  WRITE FPDMA QUEUED
  61 00 28 00 d8 00 00 e0 fd 62 c8 40 08  2d+13:43:34.059  WRITE FPDMA QUEUED

Error 44 [19] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e5 06 6e 58 40 00  Error: IDNF at LBA = 0xe5066e58 = 3842403928

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 e0 00 00 e5 06 8c 40 40 08  2d+13:41:14.715  WRITE FPDMA QUEUED
  61 01 00 00 d8 00 00 e5 06 8b 40 40 08  2d+13:41:14.715  WRITE FPDMA QUEUED
  61 00 b8 00 d0 00 00 e5 06 8a 88 40 08  2d+13:41:14.713  WRITE FPDMA QUEUED
  61 01 00 00 c8 00 00 e5 06 89 88 40 08  2d+13:41:14.710  WRITE FPDMA QUEUED
  61 01 00 00 c0 00 00 e5 06 88 88 40 08  2d+13:41:14.708  WRITE FPDMA QUEUED

Error 43 [18] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 c0 00 00 e3 23 13 e8 40 00  Error: IDNF at LBA = 0xe32313e8 = 3810726888

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 38 00 00 e3 23 14 a8 40 08  2d+13:37:04.828  WRITE FPDMA QUEUED
  61 00 c0 00 30 00 00 e3 23 13 e8 40 08  2d+13:37:04.828  WRITE FPDMA QUEUED
  61 01 00 00 28 00 00 e3 23 12 e8 40 08  2d+13:37:04.827  WRITE FPDMA QUEUED
  61 01 00 00 20 00 00 e3 23 11 e8 40 08  2d+13:37:04.827  WRITE FPDMA QUEUED
  61 01 00 00 18 00 00 e3 23 10 e8 40 08  2d+13:37:04.826  WRITE FPDMA QUEUED

Error 42 [17] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 df 68 bf f8 40 00  Error: IDNF at LBA = 0xdf68bff8 = 3748184056

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 70 00 00 df 68 dc 58 40 08  2d+13:32:04.645  WRITE FPDMA QUEUED
  61 00 38 00 68 00 00 df 68 dc 20 40 08  2d+13:32:04.645  WRITE FPDMA QUEUED
  61 01 00 00 60 00 00 df 68 db 20 40 08  2d+13:32:04.643  WRITE FPDMA QUEUED
  61 01 00 00 58 00 00 df 68 da 20 40 08  2d+13:32:04.641  WRITE FPDMA QUEUED
  61 01 00 00 50 00 00 df 68 d9 20 40 08  2d+13:32:04.637  WRITE FPDMA QUEUED

Error 41 [16] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 df 2f 47 c0 40 00  Error: IDNF at LBA = 0xdf2f47c0 = 3744417728

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 f8 00 00 df 2f 4c 78 40 08  2d+13:31:26.251  WRITE FPDMA QUEUED
  61 00 b0 00 f0 00 00 df 2f 4b c0 40 08  2d+13:31:26.251  WRITE FPDMA QUEUED
  61 01 00 00 e8 00 00 df 2f 4a c0 40 08  2d+13:31:26.251  WRITE FPDMA QUEUED
  61 01 00 00 e0 00 00 df 2f 49 c0 40 08  2d+13:31:26.250  WRITE FPDMA QUEUED
  61 01 00 00 d8 00 00 df 2f 48 c0 40 08  2d+13:31:26.250  WRITE FPDMA QUEUED

Error 40 [15] occurred at disk power-on lifetime: 10513 hours (438 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 da b0 18 f8 40 00  Error: IDNF at LBA = 0xdab018f8 = 3668973816

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 68 00 00 da b0 28 90 40 08  2d+13:27:55.974  WRITE FPDMA QUEUED
  61 00 80 00 60 00 00 da b0 28 10 40 08  2d+13:27:55.959  WRITE FPDMA QUEUED
  61 00 80 00 58 00 00 da b0 26 88 40 08  2d+13:27:55.952  WRITE FPDMA QUEUED
  61 00 80 00 50 00 00 da b0 27 08 40 08  2d+13:27:55.952  WRITE FPDMA QUEUED
  61 00 80 00 48 00 00 da b0 26 00 40 08  2d+13:27:55.952  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       50%     10225         2356483288

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    36 Celsius
Power Cycle Min/Max Temperature:     32/36 Celsius
Lifetime    Min/Max Temperature:     33/52 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (127)

Index    Estimated Time   Temperature Celsius
 128    2020-09-04 13:00    35  ****************
 ...    ..( 67 skipped).    ..  ****************
 196    2020-09-04 14:08    35  ****************
 197    2020-09-04 14:09    36  *****************
 ...    ..(379 skipped).    ..  *****************
  99    2020-09-04 20:29    36  *****************
 100    2020-09-04 20:30    35  ****************
 ...    ..( 26 skipped).    ..  ****************
 127    2020-09-04 20:57    35  ****************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x8000  4       263786  Vendor specific

For ada1

Code:

smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital RE4-GP
Device Model:     WDC WD2003FYPS-27W9B0
Serial Number:    WD-WCAVY3624623
LU WWN Device Id: 5 0014ee 2af1c5b05
Firmware Version: 04.05G09
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Fri Sep  4 20:59:55 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 128
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (39660) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 452) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  2 Throughput_Performance  --S--K   100   253   000    -    0
  3 Spin_Up_Time            POS--K   100   253   021    -    0
  4 Start_Stop_Count        -O--CK   100   100   000    -    144
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         POSR-K   200   200   051    -    0
  8 Seek_Time_Performance   --S--K   100   253   000    -    0
  9 Power_On_Hours          -O--CK   084   084   000    -    12154
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--CK   100   100   051    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    144
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   059   041   000    -    41
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    0
192 Power-Off_Retract_Count -O--CK   200   200   000    -    21
193 Load_Cycle_Count        -O--CK   200   200   000    -    122
194 Temperature_Celsius     -O---K   111   093   000    -    41
195 Hardware_ECC_Recovered  -OS-CK   200   200   000    -    0
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   P--R--   200   200   051    -    2
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80       GPL     R/W  65535  Host vendor specific log
0x80       SL      R/W    255  Host vendor specific log
0x81-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb5  GPL,SL  VS       1  Device vendor specific log
0xb6       GPL     VS       1  Device vendor specific log
0xb7       GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      24  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     11867         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    41 Celsius
Power Cycle Min/Max Temperature:     35/42 Celsius
Lifetime    Min/Max Temperature:     38/59 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (273)

Index    Estimated Time   Temperature Celsius
 274    2020-09-04 13:02    41  **********************
 ...    ..( 70 skipped).    ..  **********************
 345    2020-09-04 14:13    41  **********************
 346    2020-09-04 14:14    40  *********************
 ...    ..( 52 skipped).    ..  *********************
 399    2020-09-04 15:07    40  *********************
 400    2020-09-04 15:08    41  **********************
 ...    ..( 45 skipped).    ..  **********************
 446    2020-09-04 15:54    41  **********************
 447    2020-09-04 15:55    42  ***********************
 ...    ..(280 skipped).    ..  ***********************
 250    2020-09-04 20:36    42  ***********************
 251    2020-09-04 20:37    41  **********************
 ...    ..( 21 skipped).    ..  **********************
 273    2020-09-04 20:59    41  **********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x8000  4       263924  Vendor specific

 

[Ganzir]

For ada2

Code:

smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD80EFAX-68KNBN0
Serial Number:    VDK5T0DD
LU WWN Device Id: 5 000cca 0bbece682
Firmware Version: 81.00A81
User Capacity:    8,001,563,222,016 bytes [8.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Sep  4 21:00:54 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (   87) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 897) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     PO-R--   100   100   016    -    0
  2 Throughput_Performance  --S---   127   127   054    -    112
  3 Spin_Up_Time            POS---   100   100   024    -    0
  4 Start_Stop_Count        -O--C-   100   100   000    -    4
  5 Reallocated_Sector_Ct   PO--CK   100   100   005    -    0
  7 Seek_Error_Rate         -O-R--   100   100   067    -    0
  8 Seek_Time_Performance   --S---   128   128   020    -    18
  9 Power_On_Hours          -O--C-   100   100   000    -    311
10 Spin_Retry_Count        -O--C-   100   100   060    -    0
12 Power_Cycle_Count       -O--CK   100   100   000    -    3
192 Power-Off_Retract_Count -O--CK   100   100   000    -    15
193 Load_Cycle_Count        -O--C-   100   100   000    -    15
194 Temperature_Celsius     -O----   147   147   000    -    44 (Min/Max 25/45)
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O---K   100   100   000    -    0
198 Offline_Uncorrectable   ---R--   100   100   000    -    0
199 UDMA_CRC_Error_Count    -O-R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      1  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x04       GPL     R/O    256  Device Statistics log
0x04       SL      R/O    255  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x0c       GPL     R/O   5501  Pending Defects log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x12       GPL     R/O      1  SATA NCQ Non-Data log
0x13       GPL     R/O      1  SATA NCQ Send and Receive log
0x15       GPL     R/W      1  Rebuild Assist log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x24       GPL     R/O    256  Current Device Internal Status Data log
0x25       GPL     R/O    256  Saved Device Internal Status Data log
0x2f       GPL     -        1  Set Sector Configuration
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    44 Celsius
Power Cycle Min/Max Temperature:     36/45 Celsius
Lifetime    Min/Max Temperature:     25/45 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/65 Celsius
Min/Max Temperature Limit:           -40/70 Celsius
Temperature History Size (Index):    128 (31)

Index    Estimated Time   Temperature Celsius
  32    2020-09-04 18:53    44  *************************
...    ..(126 skipped).    ..  *************************
  31    2020-09-04 21:00    44  *************************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 1) ==
0x01  0x008  4               3  ---  Lifetime Power-On Resets
0x01  0x010  4             311  ---  Power-on Hours
0x01  0x018  6     15101384249  ---  Logical Sectors Written
0x01  0x020  6       117584340  ---  Number of Write Commands
0x01  0x028  6         4053264  ---  Logical Sectors Read
0x01  0x030  6          343698  ---  Number of Read Commands
0x01  0x038  6      1122339300  ---  Date and Time TimeStamp
0x03  =====  =               =  ===  == Rotating Media Statistics (rev 1) ==
0x03  0x008  4             309  ---  Spindle Motor Power-on Hours
0x03  0x010  4             309  ---  Head Flying Hours
0x03  0x018  4              15  ---  Head Load Events
0x03  0x020  4               0  ---  Number of Reallocated Logical Sectors
0x03  0x028  4               0  ---  Read Recovery Attempts
0x03  0x030  4               0  ---  Number of Mechanical Start Failures
0x04  =====  =               =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4               0  ---  Number of Reported Uncorrectable Errors
0x04  0x010  4               0  ---  Resets Between Cmd Acceptance and Completion
0x05  =====  =               =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1              44  ---  Current Temperature
0x05  0x010  1              44  N--  Average Short Term Temperature
0x05  0x018  1               -  N--  Average Long Term Temperature
0x05  0x020  1              45  ---  Highest Temperature
0x05  0x028  1              25  ---  Lowest Temperature
0x05  0x030  1              44  N--  Highest Average Short Term Temperature
0x05  0x038  1              25  N--  Lowest Average Short Term Temperature
0x05  0x040  1               -  N--  Highest Average Long Term Temperature
0x05  0x048  1               -  N--  Lowest Average Long Term Temperature
0x05  0x050  4               0  ---  Time in Over-Temperature
0x05  0x058  1              65  ---  Specified Maximum Operating Temperature
0x05  0x060  4               0  ---  Time in Under-Temperature
0x05  0x068  1               0  ---  Specified Minimum Operating Temperature
0x06  =====  =               =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4              60  ---  Number of Hardware Resets
0x06  0x010  4              17  ---  Number of ASR Events
0x06  0x018  4               0  ---  Number of Interface CRC Errors
0xff  =====  =               =  ===  == Vendor Specific Statistics (rev 1) ==
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

Pending Defects log (GP Log 0x0c)
No Defects Logged

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            4  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            3  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS

And for ada3

Code:

smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital RE4-GP
Device Model:     WDC WD2003FYPS-27Y2B0
Serial Number:    WD-WCAVY6438064
LU WWN Device Id: 5 0014ee 2afffa985
Firmware Version: 04.05G11
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Fri Sep  4 21:01:35 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is:     254 (maximum performance), recommended: 128
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (41580) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 473) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    5
  3 Spin_Up_Time            POS--K   253   225   021    -    8883
  4 Start_Stop_Count        -O--CK   100   100   000    -    145
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   084   084   000    -    12140
10 Spin_Retry_Count        -O--CK   100   100   000    -    0
11 Calibration_Retry_Count -O--CK   100   100   000    -    0
12 Power_Cycle_Count       -O--CK   100   100   000    -    145
192 Power-Off_Retract_Count -O--CK   200   200   000    -    22
193 Load_Cycle_Count        -O--CK   200   200   000    -    122
194 Temperature_Celsius     -O---K   113   095   000    -    39
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80       GPL     R/W  65535  Host vendor specific log
0x80       SL      R/W    255  Host vendor specific log
0x81-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb5  GPL,SL  VS       1  Device vendor specific log
0xb6       GPL     VS       1  Device vendor specific log
0xb7       GPL,SL  VS       1  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      24  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 3
        CR     = Command Register
        FEATR  = Features Register
        COUNT  = Count (was: Sector Count) Register
        LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
        LH     = LBA High (was: Cylinder High) Register    ]   LBA
        LM     = LBA Mid (was: Cylinder Low) Register      ] Register
        LL     = LBA Low (was: Sector Number) Register     ]
        DV     = Device (was: Device/Head) Register
        DC     = Device Control Register
        ER     = Error register
        ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3 [2] occurred at disk power-on lifetime: 12128 hours (505 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e5 86 d1 c8 40 00  Error: IDNF at LBA = 0xe586d1c8 = 3850817992

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 38 00 00 e5 86 d8 88 40 08  2d+13:45:25.372  WRITE FPDMA QUEUED
  61 00 80 00 30 00 00 e5 86 d8 08 40 08  2d+13:45:25.372  WRITE FPDMA QUEUED
  61 00 80 00 28 00 00 e5 86 d7 00 40 08  2d+13:45:25.372  WRITE FPDMA QUEUED
  61 00 80 00 20 00 00 e5 86 b0 d8 40 08  2d+13:45:25.372  WRITE FPDMA QUEUED
  61 00 10 00 18 00 00 da fe f5 60 40 08  2d+13:45:25.372  WRITE FPDMA QUEUED

Error 2 [1] occurred at disk power-on lifetime: 12128 hours (505 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 e0 bf e5 f8 40 00  Error: IDNF at LBA = 0xe0bfe5f8 = 3770672632

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 10 00 18 00 00 e3 6d 95 a0 40 08  2d+13:42:48.535  WRITE FPDMA QUEUED
  61 00 10 00 10 00 00 e3 6d 95 90 40 08  2d+13:42:48.533  WRITE FPDMA QUEUED
  60 00 58 00 08 00 00 e3 56 ed 60 40 08  2d+13:42:48.531  READ FPDMA QUEUED
  61 00 88 00 00 00 00 e0 bf e9 08 40 08  2d+13:42:48.529  WRITE FPDMA QUEUED
  61 01 00 00 f8 00 00 e0 bf e8 08 40 08  2d+13:42:48.526  WRITE FPDMA QUEUED

Error 1 [0] occurred at disk power-on lifetime: 12127 hours (505 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 01 00 00 00 a4 85 f4 e8 40 00  Error: IDNF at LBA = 0xa485f4e8 = 2760242408

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 01 00 00 c0 00 00 a4 85 f5 e8 40 08  2d+13:17:27.577  WRITE FPDMA QUEUED
  61 01 00 00 b8 00 00 a4 85 f4 e8 40 08  2d+13:17:27.577  WRITE FPDMA QUEUED
  61 00 c0 00 b0 00 00 a4 85 f4 28 40 08  2d+13:17:27.576  WRITE FPDMA QUEUED
  61 01 00 00 20 00 00 a4 85 f3 28 40 08  2d+13:17:27.576  WRITE FPDMA QUEUED
  61 01 00 00 a8 00 00 a4 85 f2 28 40 08  2d+13:17:27.575  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     11864         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
Device State:                        Active (0)
Current Temperature:                    39 Celsius
Power Cycle Min/Max Temperature:     35/40 Celsius
Lifetime    Min/Max Temperature:     37/57 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (374)

Index    Estimated Time   Temperature Celsius
375    2020-09-04 13:04    40  *********************
...    ..( 13 skipped).    ..  *********************
389    2020-09-04 13:18    40  *********************
390    2020-09-04 13:19    39  ********************
...    ..( 55 skipped).    ..  ********************
446    2020-09-04 14:15    39  ********************
447    2020-09-04 14:16    38  *******************
...    ..( 15 skipped).    ..  *******************
463    2020-09-04 14:32    38  *******************
464    2020-09-04 14:33    39  ********************
...    ..( 68 skipped).    ..  ********************
  55    2020-09-04 15:42    39  ********************
  56    2020-09-04 15:43    40  *********************
...    ..(317 skipped).    ..  *********************
374    2020-09-04 21:01    40  *********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x8000  4       264029  Vendor specific

Is there anything here that is cause for alarm and if not but one day something will turn critical will the system than generate an email alert?

Sorry for double posting, but the forum only allows for 30.000 characters per post.