Hello
I am doing smartctl -a on my drive and getting the following results.
The weird thing is one partition I have does not mount but the other one mounts fine. That makes me wonder whether there is a data corruption issue on just one partition or whether infact the whole drive is broken.
Thank you for your advice.
I am doing smartctl -a on my drive and getting the following results.
The weird thing is one partition I have does not mount but the other one mounts fine. That makes me wonder whether there is a data corruption issue on just one partition or whether infact the whole drive is broken.
Thank you for your advice.
Code:
root@myhost:/home/user1# smartctl -a /dev/sdb smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.0.0-13-generic] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST1000LM035-1RK172 Serial Number: WDE4S5YD LU WWN Device Id: 5 000c50 0a855e37a Firmware Version: ACM1 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 9 03:34:09 2019 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 166) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 080 052 006 Pre-fail Always - 107767397 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 037 037 020 Old_age Always - 65535 5 Reallocated_Sector_Ct 0x0033 097 097 036 Pre-fail Always - 1672 7 Seek_Error_Rate 0x000f 082 060 045 Pre-fail Always - 4453874815 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5653 (173 92 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 691 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 28429 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 069 055 040 Old_age Always - 31 (Min/Max 20/31) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 92 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 98 193 Load_Cycle_Count 0x0032 042 042 000 Old_age Always - 116839 194 Temperature_Celsius 0x0022 031 045 000 Old_age Always - 31 (0 11 0 0 0) 197 Current_Pending_Sector 0x0012 096 095 000 Old_age Always - 368 198 Offline_Uncorrectable 0x0010 096 095 000 Old_age Offline - 368 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 5460 (18 67 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 10332521622 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 13791968337 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 28431 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 28431 occurred at disk power-on lifetime: 5444 hours (226 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 3d+20:04:14.516 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+20:04:14.505 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 3d+20:04:14.479 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 3d+20:04:14.477 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+20:04:14.465 SET FEATURES [Set transfer mode] Error 28430 occurred at disk power-on lifetime: 5444 hours (226 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 3d+20:04:14.260 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:14.259 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:14.259 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:14.259 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:14.259 READ FPDMA QUEUED Error 28429 occurred at disk power-on lifetime: 5444 hours (226 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 3d+20:04:14.031 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+20:04:14.021 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 3d+20:04:13.995 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 3d+20:04:13.994 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+20:04:13.981 SET FEATURES [Set transfer mode] Error 28428 occurred at disk power-on lifetime: 5444 hours (226 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 3d+20:04:13.761 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:13.721 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:13.721 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:13.721 READ FPDMA QUEUED 60 00 08 ff ff ff 4f 00 3d+20:04:13.721 READ FPDMA QUEUED Error 28427 occurred at disk power-on lifetime: 5444 hours (226 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 ff ff ff 4f 00 3d+20:04:13.521 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+20:04:13.511 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 3d+20:04:13.484 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 3d+20:04:13.483 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+20:04:13.470 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 5653 291803192 # 2 Short offline Completed: read failure 90% 5653 291803192 # 3 Extended offline Completed: read failure 90% 5652 291803192 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.