BritshGOAT
Cadet
- Joined
- Mar 4, 2022
- Messages
- 2
Hi, I've started rebuilding my NAS, creating from a fresh start using previous drives. before I start filling my pool up, I checked every drives S.M.A.R.T
When running a LONG test 2 of my drives
give me the following alert
Looking at the smartctl output I can't tell if they are dying or not, as it shows the smart test passed. I think ./sda is dying as its has values in LBA_of_first_error column but this is only a guess? as my pool will be a single raidz2 vdev, should I change these out before starting to use my NAS again or just upgrade 1?
When running a LONG test 2 of my drives
give me the following alert
Code:
Device: /dev/sdd [SAT], Self-Test Log error count increased from 3 to 4. Device: /dev/sdd [SAT], Self-Test Log error count increased from 3 to 4.
Looking at the smartctl output I can't tell if they are dying or not, as it shows the smart test passed. I think ./sda is dying as its has values in LBA_of_first_error column but this is only a guess? as my pool will be a single raidz2 vdev, should I change these out before starting to use my NAS again or just upgrade 1?
Code:
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf Pro
Device Model: ST10000NE0008-2JM101
Serial Number: ZHZ3P5X0
LU WWN Device Id: 5 000c50 0c2bc47e0
Firmware Version: EN01
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Oct 31 05:29:43 2023 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 249) Self-test routine in progress...
90% of test remaining.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 978) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 083 064 044 Pre-fail Always - 195058177
3 Spin_Up_Time 0x0003 092 090 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 167
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 96
7 Seek_Error_Rate 0x000f 089 060 045 Pre-fail Always - 786170628
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20784
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 169
18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 1
190 Airflow_Temperature_Cel 0x0022 061 023 040 Old_age Always In_the_past 39 (48 120 39 32 0)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 112
193 Load_Cycle_Count 0x0032 093 093 000 Old_age Always - 14203
194 Temperature_Celsius 0x0022 039 077 000 Old_age Always - 39 (0 13 0 0 0)
195 Hardware_ECC_Recovered 0x001a 083 064 000 Old_age Always - 195058177
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 19365h+54m+31.004s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 94449578193
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 498694099818
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Self-test routine in progress 90% 20784 -
# 2 Extended offline Completed: read failure 90% 20784 -
# 3 Short offline Completed: read failure 90% 20713 -
# 4 Short offline Completed: read failure 90% 20600 -
# 5 Short offline Completed: read failure 90% 20432 -
# 6 Extended offline Completed without error 00% 20395 -
# 7 Short offline Completed: read failure 90% 20313 -
# 8 Short offline Completed: read failure 90% 20145 -
# 9 Short offline Completed: read failure 90% 20000 -
#10 Short offline Completed: read failure 90% 19832 -
#11 Extended offline Completed without error 00% 19730 -
#12 Short offline Completed without error 00% 19664 -
#13 Extended offline Interrupted (host reset) 00% 18831 -
#14 Extended offline Interrupted (host reset) 00% 18810 -
#15 Extended offline Completed without error 00% 18796 -
#16 Extended offline Completed without error 00% 18772 -
#17 Extended offline Completed without error 00% 18748 -
#18 Extended offline Completed without error 00% 18724 -
#19 Extended offline Completed without error 00% 18690 -
#20 Extended offline Completed: read failure 90% 18637 -
#21 Extended offline Completed: read failure 90% 18613 -
6 of 10 failed self-tests are outdated by newer successful extended offline self-test # 6
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Code:
=== START OF INFORMATION SECTION ===
Model Family: Seagate BarraCuda 3.5
Device Model: ST8000DM004-2CX188
Serial Number: WSC07XF1
LU WWN Device Id: 5 000c50 0d637dda3
Firmware Version: 0001
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5425 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Oct 31 05:43:57 2023 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 999) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30a5) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 077 054 006 Pre-fail Always - 54799575
3 Spin_Up_Time 0x0003 092 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2253
5 Reallocated_Sector_Ct 0x0033 098 098 010 Pre-fail Always - 4736
7 Seek_Error_Rate 0x000f 095 060 045 Pre-fail Always - 2826869110
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 16984 (68 15 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 195
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 030 030 000 Old_age Always - 70
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 6 6 14
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 064 027 040 Old_age Always In_the_past 36 (21 236 36 31 0)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 674
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2953
194 Temperature_Celsius 0x0022 036 073 000 Old_age Always - 36 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 077 064 000 Old_age Always - 54799575
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 112
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 112
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 15797h+36m+33.903s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 73043916656
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 323584380662
SMART Error Log Version: 1
ATA Error Count: 70 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 70 occurred at disk power-on lifetime: 16951 hours (706 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 3d+13:12:48.374 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:48.374 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:48.373 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:48.373 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:48.360 READ FPDMA QUEUED
Error 69 occurred at disk power-on lifetime: 16951 hours (706 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 80 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+13:12:47.762 READ FPDMA QUEUED
60 00 90 ff ff ff 4f 00 3d+13:12:47.760 READ FPDMA QUEUED
60 00 78 ff ff ff 4f 00 3d+13:12:47.759 READ FPDMA QUEUED
Error 68 occurred at disk power-on lifetime: 16946 hours (706 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 3d+08:46:02.688 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+08:46:02.678 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+08:46:02.678 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+08:46:02.677 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+08:46:02.676 READ FPDMA QUEUED
Error 67 occurred at disk power-on lifetime: 16946 hours (706 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 3d+08:46:01.980 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:46:01.974 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:46:01.968 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+08:46:01.963 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+08:46:01.962 READ FPDMA QUEUED
Error 66 occurred at disk power-on lifetime: 16942 hours (705 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 ff ff ff 4f 00 3d+04:42:49.107 WRITE FPDMA QUEUED
61 00 00 ff ff ff 4f 00 3d+04:42:49.107 WRITE FPDMA QUEUED
60 00 00 ff ff ff 4f 00 3d+04:42:49.104 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+04:42:49.045 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 3d+04:42:49.041 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 16984 -
# 2 Extended offline Completed: read failure 90% 16984 -
# 3 Short offline Completed without error 00% 16913 -
# 4 Short offline Completed without error 00% 16758 -
# 5 Short offline Completed: read failure 90% 16590 2806846328
# 6 Extended offline Completed: read failure 90% 16518 2806846328
# 7 Short offline Completed without error 00% 16472 -
# 8 Short offline Completed: read failure 90% 16304 2806846328
# 9 Short offline Completed without error 00% 16158 -
#10 Short offline Completed: read failure 90% 15990 -
#11 Extended offline Completed: read failure 90% 15870 -
#12 Short offline Completed without error 00% 15824 -
#13 Short offline Completed without error 00% 15656 -
#14 Short offline Completed without error 00% 15641 -
#15 Extended offline Interrupted (host reset) 00% 15640 -
#16 Short offline Completed without error 00% 15582 -
#17 Short offline Completed without error 00% 15409 -
#18 Short offline Completed without error 00% 15160 -
#19 Short offline Completed without error 00% 14992 -
#20 Short offline Completed without error 00% 14824 -
#21 Extended offline Interrupted (host reset) 90% 14783 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Don't replace them! Keep them in your server forever! Give yourself another five years or so before making a decision. Enjoy life. Don't stress yourself with the burdens of a NAS server.
