I need smartd to produce a proper config file, the settings would be /dev/arcmsr0 -d areca,5/2 or something similar, I checked the ix-smartd and the problem is it doesnt have the /2, so naturally I just added it because I only need it for this one raid card. but for whatever reason when I start smartd it only shows one hard drive at 13/2 and it is the only hard drive I do not have ZFS or any a smart tests added. currently running.
camcontrol devlist
<NECVMWar VMware IDE CDR10 1.00> at scbus1 target 0 lun 0 (cd0,pass0)
<VMware Virtual disk 1.0> at scbus2 target 0 lun 0 (da0,pass1)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 4 (da1,pass2)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 5 (da2,pass3)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 6 (da3,pass4)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 7 (da4,pass5)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 0 (da5,pass6)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 1 (da6,pass7)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 2 (da7,pass8)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 3 (da8,pass9)
<Seagate ST4000NM0033-9ZM R001> at scbus3 target 2 lun 4 (da9,pass10)
<Areca RAID controller R001> at scbus3 target 16 lun 0 (pass11)
the camcontrol tmp file shows up like this
ata|1|0|0|cd0
mpt|0|0|0|da0
arcmsr|0|1|4|da1
arcmsr|0|1|5|da2
arcmsr|0|1|6|da3
arcmsr|0|1|7|da4
arcmsr|0|2|0|da5
arcmsr|0|2|1|da6
arcmsr|0|2|2|da7
arcmsr|0|2|3|da8
arcmsr|0|2|4|da9
arcmsr|0|16|0|
but for some reason when the /2 is added only one the one shows up...
################################################
# smartd.conf generated by /etc/rc.d/ix-smartd
################################################
/dev/arcmsr0 -d areca,13/2 -a -n never -W 0,50,55 -m ----------@gmail.com -s L/(0
1|02|03|04|05|06|07|08|09|10|11|12)/../(3)/(21)
/dev/arcmsr0 -d areca,13/2 -a -n never -W 0,50,55 -m ----------@gmail.com -s S/(0
1|02|03|04|05|06|07|08|09|10|11|12)/../(2|4|6)/(19)|1|0|0|cd0
the smart test I added in the gui were for da1 and the disk its showing is da9 Im going to continue working on this but any help would be great! thanks =]
camcontrol devlist
<NECVMWar VMware IDE CDR10 1.00> at scbus1 target 0 lun 0 (cd0,pass0)
<VMware Virtual disk 1.0> at scbus2 target 0 lun 0 (da0,pass1)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 4 (da1,pass2)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 5 (da2,pass3)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 6 (da3,pass4)
<Seagate ST31500341AS R001> at scbus3 target 1 lun 7 (da4,pass5)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 0 (da5,pass6)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 1 (da6,pass7)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 2 (da7,pass8)
<Seagate ST31500341AS R001> at scbus3 target 2 lun 3 (da8,pass9)
<Seagate ST4000NM0033-9ZM R001> at scbus3 target 2 lun 4 (da9,pass10)
<Areca RAID controller R001> at scbus3 target 16 lun 0 (pass11)
the camcontrol tmp file shows up like this
ata|1|0|0|cd0
mpt|0|0|0|da0
arcmsr|0|1|4|da1
arcmsr|0|1|5|da2
arcmsr|0|1|6|da3
arcmsr|0|1|7|da4
arcmsr|0|2|0|da5
arcmsr|0|2|1|da6
arcmsr|0|2|2|da7
arcmsr|0|2|3|da8
arcmsr|0|2|4|da9
arcmsr|0|16|0|
but for some reason when the /2 is added only one the one shows up...
################################################
# smartd.conf generated by /etc/rc.d/ix-smartd
################################################
/dev/arcmsr0 -d areca,13/2 -a -n never -W 0,50,55 -m ----------@gmail.com -s L/(0
1|02|03|04|05|06|07|08|09|10|11|12)/../(3)/(21)
/dev/arcmsr0 -d areca,13/2 -a -n never -W 0,50,55 -m ----------@gmail.com -s S/(0
1|02|03|04|05|06|07|08|09|10|11|12)/../(2|4|6)/(19)|1|0|0|cd0
the smart test I added in the gui were for da1 and the disk its showing is da9 Im going to continue working on this but any help would be great! thanks =]