periph not created back

[Juan Pablo Abuyeres]

I had this:
[root@TCN-05-LON-SN1] ~# camcontrol devlist
<Mushkin MKNSSDCL60GB-DX 320A13F0> at scbus2 target 0 lun 0 (pass0,ada0)
<Mushkin MKNSSDCL60GB-DX 320A13F0> at scbus3 target 0 lun 0 (pass1,ada1)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 0 (pass2,da0)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 1 (pass3,da1)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 2 (pass4,da2)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 3 (pass5,da3)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 4 (pass6,da4)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 5 (pass7,da5)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 6 (pass8,da6)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 7 (pass9,da7)
<HGST HUS726060ALS640 R001> at scbus8 target 1 lun 0 (pass10,da8)
<HGST HUS726060ALS640 R001> at scbus8 target 1 lun 1 (pass11,da9)
<KINGSTON SH103S3480G R001> at scbus8 target 1 lun 2 (pass12,da10)
<KINGSTON SE50S3100G R001> at scbus8 target 1 lun 3 (pass13,da11)
<Areca RAID controller R001> at scbus8 target 16 lun 0 (pass14)
[root@TCN-05-LON-SN1] ~#

I detached a hard drive (da0) from my freenas, to simulate a hard drive replace, and it was detached correctly.

Jul 7 13:26:12 TCN-05-LON-SN1 arcmsr_dr_handle: Target=0, lun=0, GONE!!!
Jul 7 13:26:12 TCN-05-LON-SN1 da0 at arcmsr0 bus 0 scbus8 target 0 lun 0
Jul 7 13:26:12 TCN-05-LON-SN1 da0: <HGST HUS726060ALS640 R001> s/n 1EHJNYSC detached
Jul 7 13:26:12 TCN-05-LON-SN1 GEOM_ELI: Device da0p1.eli destroyed.
Jul 7 13:26:12 TCN-05-LON-SN1 GEOM_ELI: Detached da0p1.eli on last close.
Jul 7 13:26:12 TCN-05-LON-SN1 (da0:arcmsr0:0:0:0): Periph destroyed

But then, when I plug the hard drive, the periph da0 is not created

Jul 7 13:27:12 TCN-05-LON-SN1 arcmsr_dr_handle: Target=0, lun=0, Plug-IN!!!

[root@TCN-05-LON-SN1] ~# camcontrol devlist
<Mushkin MKNSSDCL60GB-DX 320A13F0> at scbus2 target 0 lun 0 (pass0,ada0)
<Mushkin MKNSSDCL60GB-DX 320A13F0> at scbus3 target 0 lun 0 (pass1,ada1)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 0 ()
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 1 (pass3,da1)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 2 (pass4,da2)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 3 (pass5,da3)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 4 (pass6,da4)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 5 (pass7,da5)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 6 (pass8,da6)
<HGST HUS726060ALS640 R001> at scbus8 target 0 lun 7 (pass9,da7)
<HGST HUS726060ALS640 R001> at scbus8 target 1 lun 0 (pass10,da8)
<HGST HUS726060ALS640 R001> at scbus8 target 1 lun 1 (pass11,da9)
<KINGSTON SH103S3480G R001> at scbus8 target 1 lun 2 (pass12,da10)
<KINGSTON SE50S3100G R001> at scbus8 target 1 lun 3 (pass13,da11)
<Areca RAID controller R001> at scbus8 target 16 lun 0 (pass14)
[root@TCN-05-LON-SN1] ~#

It doesnt create da0. If I reboot it gets fixed. But I need not to reboot.

Please advise what to do. The controller is an areca 1880 card. If I am right, this worked fine on 9.2.1.9, and now in 9.3 it doesn´t.

Thank you.

 

[dlavigne]

Did you figure this out?