LIGISTX
Guru
- Joined
- Apr 12, 2015
- Messages
- 525
I received an email this morning that reads:
New alerts:
* Device: /dev/da5 [SAT], Self-Test Log error count increased from 0 to 1
Upon running my script to email me issues, I see this:
I am not 100% sure what this is telling me here. The overall "PASSED" makes me not exactly sure what is going on.
I ran smartctl and got this wonderful output... once again, not sure what I am looking for.
New alerts:
* Device: /dev/da5 [SAT], Self-Test Log error count increased from 0 to 1
Upon running my script to email me issues, I see this:
Code:
########## SMART status report for da5 drive (Western Digital Red: WD-xxxxxxx) ########## smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) SMART overall-health self-assessment test result: PASSED ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 155 153 021 Pre-fail Always - 7233 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 147 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 17693 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 144 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 141 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 69 194 Temperature_Celsius 0x0022 115 102 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1 No Errors Logged Test_Description Status Remaining LifeTime(hours) LBA_of_first_error Extended offline Completed: read failure 10% 17683 2852532304 Short offline Completed without error 00% 17604 -
I am not 100% sure what this is telling me here. The overall "PASSED" makes me not exactly sure what is going on.
I ran smartctl and got this wonderful output... once again, not sure what I am looking for.
Code:
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD40EFRX-68N32N0
Serial Number: WD-xxxxxx
LU WWN Device Id: 5 0014ee 264915ee0
Firmware Version: 82.00A82
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Dec 9 18:16:28 2019 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 113) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (44400) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 471) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 155 153 021 - 7233
4 Start_Stop_Count -O--CK 100 100 000 - 147
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 076 076 000 - 17693
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 144
192 Power-Off_Retract_Count -O--CK 200 200 000 - 141
193 Load_Cycle_Count -O--CK 200 200 000 - 69
194 Temperature_Celsius -O---K 116 102 000 - 34
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 56 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 11
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 11 [10] occurred at disk power-on lifetime: 3905 hours (162 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:11:23.785 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:11:23.785 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:11:23.785 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:11:23.785 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:11:23.785 READ FPDMA QUEUED
Error 10 [9] occurred at disk power-on lifetime: 3905 hours (162 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:09:58.544 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:09:58.544 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:09:58.544 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:09:58.543 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:09:58.543 READ FPDMA QUEUED
Error 9 [8] occurred at disk power-on lifetime: 3759 hours (156 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 3d+02:37:00.679 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 3d+02:37:00.679 READ FPDMA QUEUED
Error 8 [7] occurred at disk power-on lifetime: 3637 hours (151 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 01:56:29.988 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 01:56:29.988 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 01:56:29.988 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 01:56:29.988 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 01:56:29.987 READ FPDMA QUEUED
Error 7 [6] occurred at disk power-on lifetime: 1912 hours (79 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.245 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.245 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:04.245 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.245 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.245 READ FPDMA QUEUED
Error 6 [5] occurred at disk power-on lifetime: 783 hours (32 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:03.993 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:03.993 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:03.992 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:03.992 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:03.992 READ FPDMA QUEUED
Error 5 [4] occurred at disk power-on lifetime: 780 hours (32 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:06.347 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:06.347 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:06.347 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:06.347 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:06.347 READ FPDMA QUEUED
Error 4 [3] occurred at disk power-on lifetime: 780 hours (32 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.149 WRITE FPDMA QUEUED
61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.149 WRITE FPDMA QUEUED
61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:04.149 WRITE FPDMA QUEUED
60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.149 READ FPDMA QUEUED
60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.149 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 10% 17683 7147499600
# 2 Short offline Completed without error 00% 17604 -
# 3 Short offline Completed without error 00% 17388 -
# 4 Extended offline Completed without error 00% 17301 -
# 5 Short offline Completed without error 00% 17221 -
# 6 Short offline Completed without error 00% 17053 -
# 7 Extended offline Completed without error 00% 16965 -
# 8 Short offline Completed without error 00% 16885 -
# 9 Short offline Completed without error 00% 16644 -
#10 Extended offline Completed without error 00% 16557 -
#11 Short offline Completed without error 00% 16476 -
#12 Short offline Completed without error 00% 16309 -
#13 Extended offline Completed without error 00% 16222 -
#14 Short offline Completed without error 00% 16141 -
#15 Short offline Completed without error 00% 15925 -
#16 Extended offline Completed without error 00% 15838 -
#17 Short offline Completed without error 00% 15757 -
#18 Short offline Completed without error 00% 15633 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 34 Celsius
Power Cycle Min/Max Temperature: 26/44 Celsius
Lifetime Min/Max Temperature: 18/48 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/65 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (364)
Index Estimated Time Temperature Celsius
365 2019-12-09 10:19 33 **************
... ..( 63 skipped). .. **************
429 2019-12-09 11:23 33 **************
430 2019-12-09 11:24 34 ***************
... ..(117 skipped). .. ***************
70 2019-12-09 13:22 34 ***************
71 2019-12-09 13:23 35 ****************
... ..(126 skipped). .. ****************
198 2019-12-09 15:30 35 ****************
199 2019-12-09 15:31 34 ***************
... ..( 19 skipped). .. ***************
219 2019-12-09 15:51 34 ***************
220 2019-12-09 15:52 33 **************
... ..(143 skipped). .. **************
364 2019-12-09 18:16 33 **************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 144 --- Lifetime Power-On Resets
0x01 0x010 4 17693 --- Power-on Hours
0x01 0x018 6 55346693565 --- Logical Sectors Written
0x01 0x020 6 923946836 --- Number of Write Commands
0x01 0x028 6 224391048303 --- Logical Sectors Read
0x01 0x030 6 1564280091 --- Number of Read Commands
0x01 0x038 6 3565257856 --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 17619 --- Spindle Motor Power-on Hours
0x03 0x010 4 17523 --- Head Flying Hours
0x03 0x018 4 211 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 1 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 141 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 11 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 34 --- Current Temperature
0x05 0x010 1 34 --- Average Short Term Temperature
0x05 0x018 1 32 --- Average Long Term Temperature
0x05 0x020 1 48 --- Highest Temperature
0x05 0x028 1 23 --- Lowest Temperature
0x05 0x030 1 44 --- Highest Average Short Term Temperature
0x05 0x038 1 24 --- Lowest Average Short Term Temperature
0x05 0x040 1 37 --- Highest Average Long Term Temperature
0x05 0x048 1 28 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 65 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 1828 --- Number of Hardware Resets
0x06 0x010 4 25 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 3 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 6979318 Vendor specific
