LIGISTX
Guru
- Joined
- Apr 12, 2015
- Messages
- 525
I received an email this morning that reads:
New alerts:
* Device: /dev/da5 [SAT], Self-Test Log error count increased from 0 to 1
Upon running my script to email me issues, I see this:
I am not 100% sure what this is telling me here. The overall "PASSED" makes me not exactly sure what is going on.
I ran smartctl and got this wonderful output... once again, not sure what I am looking for.
New alerts:
* Device: /dev/da5 [SAT], Self-Test Log error count increased from 0 to 1
Upon running my script to email me issues, I see this:
Code:
########## SMART status report for da5 drive (Western Digital Red: WD-xxxxxxx) ########## smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) SMART overall-health self-assessment test result: PASSED ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 155 153 021 Pre-fail Always - 7233 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 147 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 17693 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 144 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 141 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 69 194 Temperature_Celsius 0x0022 115 102 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1 No Errors Logged Test_Description Status Remaining LifeTime(hours) LBA_of_first_error Extended offline Completed: read failure 10% 17683 2852532304 Short offline Completed without error 00% 17604 -
I am not 100% sure what this is telling me here. The overall "PASSED" makes me not exactly sure what is going on.
I ran smartctl and got this wonderful output... once again, not sure what I am looking for.
Code:
=== START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD40EFRX-68N32N0 Serial Number: WD-xxxxxx LU WWN Device Id: 5 0014ee 264915ee0 Firmware Version: 82.00A82 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Dec 9 18:16:28 2019 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 113) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (44400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 471) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 155 153 021 - 7233 4 Start_Stop_Count -O--CK 100 100 000 - 147 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 076 076 000 - 17693 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 144 192 Power-Off_Retract_Count -O--CK 200 200 000 - 141 193 Load_Cycle_Count -O--CK 200 200 000 - 69 194 Temperature_Celsius -O---K 116 102 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 56 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 11 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 11 [10] occurred at disk power-on lifetime: 3905 hours (162 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:11:23.785 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:11:23.785 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:11:23.785 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:11:23.785 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:11:23.785 READ FPDMA QUEUED Error 10 [9] occurred at disk power-on lifetime: 3905 hours (162 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:09:58.544 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:09:58.544 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:09:58.544 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:09:58.543 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:09:58.543 READ FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 3759 hours (156 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 3d+02:37:00.679 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 3d+02:37:00.679 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 3d+02:37:00.679 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 3637 hours (151 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 01:56:29.988 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 01:56:29.988 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 01:56:29.988 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 01:56:29.988 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 01:56:29.987 READ FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 1912 hours (79 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.245 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.245 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:04.245 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.245 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.245 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 783 hours (32 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:03.993 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:03.993 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:03.992 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:03.992 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:03.992 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 780 hours (32 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:06.347 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:06.347 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:06.347 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:06.347 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:06.347 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 780 hours (32 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 40 02 90 40 00 Error: IDNF at LBA = 0x00400290 = 4194960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.149 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.149 WRITE FPDMA QUEUED 61 00 10 00 00 00 00 00 40 02 90 40 00 00:01:04.149 WRITE FPDMA QUEUED 60 00 10 00 10 00 01 d1 c0 bc 90 40 00 00:01:04.149 READ FPDMA QUEUED 60 00 10 00 08 00 01 d1 c0 ba 90 40 00 00:01:04.149 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 10% 17683 7147499600 # 2 Short offline Completed without error 00% 17604 - # 3 Short offline Completed without error 00% 17388 - # 4 Extended offline Completed without error 00% 17301 - # 5 Short offline Completed without error 00% 17221 - # 6 Short offline Completed without error 00% 17053 - # 7 Extended offline Completed without error 00% 16965 - # 8 Short offline Completed without error 00% 16885 - # 9 Short offline Completed without error 00% 16644 - #10 Extended offline Completed without error 00% 16557 - #11 Short offline Completed without error 00% 16476 - #12 Short offline Completed without error 00% 16309 - #13 Extended offline Completed without error 00% 16222 - #14 Short offline Completed without error 00% 16141 - #15 Short offline Completed without error 00% 15925 - #16 Extended offline Completed without error 00% 15838 - #17 Short offline Completed without error 00% 15757 - #18 Short offline Completed without error 00% 15633 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 26/44 Celsius Lifetime Min/Max Temperature: 18/48 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (364) Index Estimated Time Temperature Celsius 365 2019-12-09 10:19 33 ************** ... ..( 63 skipped). .. ************** 429 2019-12-09 11:23 33 ************** 430 2019-12-09 11:24 34 *************** ... ..(117 skipped). .. *************** 70 2019-12-09 13:22 34 *************** 71 2019-12-09 13:23 35 **************** ... ..(126 skipped). .. **************** 198 2019-12-09 15:30 35 **************** 199 2019-12-09 15:31 34 *************** ... ..( 19 skipped). .. *************** 219 2019-12-09 15:51 34 *************** 220 2019-12-09 15:52 33 ************** ... ..(143 skipped). .. ************** 364 2019-12-09 18:16 33 ************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 144 --- Lifetime Power-On Resets 0x01 0x010 4 17693 --- Power-on Hours 0x01 0x018 6 55346693565 --- Logical Sectors Written 0x01 0x020 6 923946836 --- Number of Write Commands 0x01 0x028 6 224391048303 --- Logical Sectors Read 0x01 0x030 6 1564280091 --- Number of Read Commands 0x01 0x038 6 3565257856 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 17619 --- Spindle Motor Power-on Hours 0x03 0x010 4 17523 --- Head Flying Hours 0x03 0x018 4 211 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 141 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 11 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 34 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 44 --- Highest Average Short Term Temperature 0x05 0x038 1 24 --- Lowest Average Short Term Temperature 0x05 0x040 1 37 --- Highest Average Long Term Temperature 0x05 0x048 1 28 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1828 --- Number of Hardware Resets 0x06 0x010 4 25 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 6979318 Vendor specific