dias
Dabbler
- Joined
- Nov 3, 2022
- Messages
- 24
Hi,
I am a newbie at truenas, just installed scale. I have 2 pools.
System:
TrueNAS-SCALE-22.02.4 (Baremetal)
Pool 1:
2x 12 tb seagate exos mirror
Pool 2:
2x 8 tb wd red pro mirror
Main boot drive:
240 gb sandisk ssd
Board:
Msi z170a gaming m7
Ethernet Card:
Intel 82599En 10 gbit spf+
Cpu:
Intel(R) Core(TM) i5-6500 CPU @ 3.20GHz
Ram:
1x8 gb ram Non-ecc ram (dont know brand)
Case:
Thermaltake level 10 GTS
Case,Raid drives and nic are brand new others are old stuff.
I am getting degraded notification from one of my wd red pro drive (sdb). I ran both short and long smart tests for this drive and it was success. Pool seems to be working fine other than that. I can transfer files to this pool from lan but it was annoying me to see that error on new disks. I tried to change sata cables to see if there was an error with cables but it made that pool unavaible then so i changed the cables back. Is it normal to see degraded notifications on new drive? How can i troubleshoot this?
Vpool Status:
Here is the smart results:
I am a newbie at truenas, just installed scale. I have 2 pools.
System:
TrueNAS-SCALE-22.02.4 (Baremetal)
Pool 1:
2x 12 tb seagate exos mirror
Pool 2:
2x 8 tb wd red pro mirror
Main boot drive:
240 gb sandisk ssd
Board:
Msi z170a gaming m7
Ethernet Card:
Intel 82599En 10 gbit spf+
Cpu:
Intel(R) Core(TM) i5-6500 CPU @ 3.20GHz
Ram:
1x8 gb ram Non-ecc ram (dont know brand)
Case:
Thermaltake level 10 GTS
Case,Raid drives and nic are brand new others are old stuff.
I am getting degraded notification from one of my wd red pro drive (sdb). I ran both short and long smart tests for this drive and it was success. Pool seems to be working fine other than that. I can transfer files to this pool from lan but it was annoying me to see that error on new disks. I tried to change sata cables to see if there was an error with cables but it made that pool unavaible then so i changed the cables back. Is it normal to see degraded notifications on new drive? How can i troubleshoot this?
Vpool Status:
Code:
root@truenas[~]# zpool status -v
pool: boot-pool
state: ONLINE
status: Some supported and requested features are not enabled on the pool.
The pool can still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
config:
NAME STATE READ WRITE CKSUM
boot-pool ONLINE 0 0 0
sda3 ONLINE 0 0 0
errors: No known data errors
pool: seagate
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
seagate ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
4ced2a17-6b88-4bec-a301-ae54cb41d627 ONLINE 0 0 0
fbf0eef0-74af-4c71-9702-6371eaf3fbb1 ONLINE 0 0 0
errors: No known data errors
pool: wd
state: DEGRADED
status: One or more devices are faulted in response to persistent errors.
Sufficient replicas exist for the pool to continue functioning in a
degraded state.
action: Replace the faulted device, or use 'zpool clear' to mark the device
repaired.
scan: resilvered 712K in 00:00:19 with 0 errors on Wed Nov 2 23:47:38 2022
config:
NAME STATE READ WRITE CKSUM
wd DEGRADED 0 0 0
mirror-0 DEGRADED 0 0 0
b9e99684-cab8-4adf-add3-dacadae436ef FAULTED 0 3 0 too many errors
d16360d8-1281-4b39-bfc0-585bb9f5f37a ONLINE 0 0 0
errors: No known data errors
root@truenas[~]# Here is the smart results:
Code:
root@truenas[~]# smartctl -qnoserial -x /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.142+truenas] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red Pro
Device Model: WDC WD8003FFBX-68B9AN0
Firmware Version: 83.00A83
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Nov 3 14:58:56 2022 +03
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 87) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 889) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance --S--- 132 132 054 - 96
3 Spin_Up_Time POS--- 157 157 024 - 537 (Average 496)
4 Start_Stop_Count -O--C- 100 100 000 - 284
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate -O-R-- 100 100 067 - 0
8 Seek_Time_Performance --S--- 128 128 020 - 18
9 Power_On_Hours -O--C- 100 100 000 - 607
10 Spin_Retry_Count -O--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 26
192 Power-Off_Retract_Count -O--CK 100 100 000 - 317
193 Load_Cycle_Count -O--C- 100 100 000 - 317
194 Temperature_Celsius -O---- 120 120 000 - 50 (Min/Max 21/53)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 196 196 000 - 29
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 256 Device Statistics log
0x04 SL R/O 255 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 5501 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x12 GPL R/O 1 SATA NCQ Non-Data log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x15 GPL R/W 1 Rebuild Assist log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x24 GPL R/O 256 Current Device Internal Status Data log
0x25 GPL R/O 256 Saved Device Internal Status Data log
0x2f GPL - 1 Set Sector Configuration
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 29 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 29 [0] occurred at disk power-on lifetime: 592 hours (24 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 43 00 00 00 00 00 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 80 00 00 00 40 02 90 40 08 00:01:13.651 WRITE FPDMA QUEUED
61 00 10 00 78 00 03 a3 81 26 90 40 08 00:01:13.650 WRITE FPDMA QUEUED
61 00 10 00 70 00 03 a3 81 28 90 40 08 00:01:13.650 WRITE FPDMA QUEUED
47 00 00 00 01 00 00 00 00 00 12 a0 08 00:01:13.635 READ LOG DMA EXT
47 00 00 00 01 00 00 00 00 00 00 a0 08 00:01:13.634 READ LOG DMA EXT
Error 28 [3] occurred at disk power-on lifetime: 592 hours (24 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 43 00 00 00 00 00 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 40 00 00 00 40 02 90 40 08 00:01:13.202 WRITE FPDMA QUEUED
61 00 10 00 50 00 03 a3 81 28 90 40 08 00:01:13.202 WRITE FPDMA QUEUED
61 00 10 00 48 00 03 a3 81 26 90 40 08 00:01:13.202 WRITE FPDMA QUEUED
47 00 00 00 01 00 00 00 00 00 12 a0 08 00:01:13.187 READ LOG DMA EXT
47 00 00 00 01 00 00 00 00 00 00 a0 08 00:01:13.186 READ LOG DMA EXT
Error 27 [2] occurred at disk power-on lifetime: 592 hours (24 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 43 00 00 00 00 00 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 70 00 00 00 40 02 90 40 08 00:01:12.779 WRITE FPDMA QUEUED
61 00 10 00 68 00 03 a3 81 26 90 40 08 00:01:12.779 WRITE FPDMA QUEUED
61 00 10 00 60 00 03 a3 81 28 90 40 08 00:01:12.779 WRITE FPDMA QUEUED
47 00 00 00 01 00 00 00 00 00 12 a0 08 00:01:12.777 READ LOG DMA EXT
47 00 00 00 01 00 00 00 00 00 00 a0 08 00:01:12.777 READ LOG DMA EXT
Error 26 [1] occurred at disk power-on lifetime: 592 hours (24 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 43 00 00 00 00 00 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 10 00 18 00 00 00 40 02 90 40 08 00:01:12.411 WRITE FPDMA QUEUED
61 00 10 00 28 00 03 a3 81 28 90 40 08 00:01:12.411 WRITE FPDMA QUEUED
61 00 10 00 20 00 03 a3 81 26 90 40 08 00:01:12.411 WRITE FPDMA QUEUED
60 00 10 00 c0 00 03 a3 81 28 90 40 08 00:01:12.411 READ FPDMA QUEUED
60 00 10 00 b8 00 03 a3 81 26 90 40 08 00:01:12.411 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 606 -
# 2 Short offline Completed without error 00% 592 -
# 3 Short offline Completed without error 00% 560 -
# 4 Short offline Completed without error 00% 7 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 50 Celsius
Power Cycle Min/Max Temperature: 46/53 Celsius
Lifetime Min/Max Temperature: 21/53 Celsius
Under/Over Temperature Limit Count: 0/0
Write SCT Data Table failed: scsi error badly formed scsi parameters
Read SCT Temperature History failed
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 26 --- Lifetime Power-On Resets
0x01 0x010 4 607 --- Power-on Hours
0x01 0x018 6 23424995762 --- Logical Sectors Written
0x01 0x020 6 132433109 --- Number of Write Commands
0x01 0x028 6 7144645036 --- Logical Sectors Read
0x01 0x030 6 23174675 --- Number of Read Commands
0x01 0x038 6 2185910450 --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 488 --- Spindle Motor Power-on Hours
0x03 0x010 4 488 --- Head Flying Hours
0x03 0x018 4 317 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 29 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 50 --- Current Temperature
0x05 0x010 1 51 N-- Average Short Term Temperature
0x05 0x018 1 45 N-- Average Long Term Temperature
0x05 0x020 1 53 --- Highest Temperature
0x05 0x028 1 21 --- Lowest Temperature
0x05 0x030 1 51 N-- Highest Average Short Term Temperature
0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
0x05 0x040 1 45 N-- Highest Average Long Term Temperature
0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 168 --- Number of Hardware Resets
0x06 0x010 4 33 --- Number of ASR Events
0x06 0x018 4 30 --- Number of Interface CRC Errors
0xff ===== = = === == Vendor Specific Statistics (rev 1) ==
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c)
No Defects Logged
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 5 Command failed due to ICRC error
0x0002 2 5 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 5 R_ERR response for host-to-device data FIS
0x0005 2 4 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 4 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 8 Device-to-host register FISes sent due to a COMRESET
0x000b 2 5 CRC errors within host-to-device FIS
0x000d 2 4 Non-CRC errors within host-to-device FIS
