Mostly_Broken
Cadet
- Joined
- Mar 26, 2021
- Messages
- 3
Hi all,
had a couple of ATA error count increases yeserday... I seem to think these were both triggered around the times I instructed truenas to run a test.
No SMART tests fail - disk was ran through a 10+ hours long test 2 days ago before going into this system (using seatools).
SMARTcrtl printout: - could somebody please help me figure out what the ATA errors are / what caused them?
had a couple of ATA error count increases yeserday... I seem to think these were both triggered around the times I instructed truenas to run a test.
No SMART tests fail - disk was ran through a 10+ hours long test 2 days ago before going into this system (using seatools).
SMARTcrtl printout: - could somebody please help me figure out what the ATA errors are / what caused them?
Code:
root@truenas[~]# smartctl -a /dev/da0
smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: MB4000GCWLV
Serial Number: PBJX3MVS
LU WWN Device Id: 5 000cca 23de8f710
Firmware Version: HPG3
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Apr 3 09:55:31 2021 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 536) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0027 138 100 054 Pre-fail Always - 75
3 Spin_Up_Time 0x0023 147 100 024 Pre-fail Always - 564 (Average 487)
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 72
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 140 100 020 Pre-fail Offline - 26
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 35980
10 Spin_Retry_Count 0x0033 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 69
180 Unknown_HDD_Attribute 0x002b 100 100 098 Pre-fail Always - 0
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
185 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 65535
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 1
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 050 000 Old_age Always - 33 (Min/Max 33/35)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 863
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 864
194 Temperature_Celsius 0x0022 181 120 000 Old_age Always - 33 (Min/Max 13/50)
196 Reallocated_Event_Count 0x0033 100 100 000 Pre-fail Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 148 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 148 occurred at disk power-on lifetime: 35980 hours (1499 days + 4 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d4 00 03 4f c2 00 00 00:30:26.909 SMART EXECUTE OFF-LINE IMMEDIATE
b0 d0 01 00 4f c2 00 00 00:30:26.681 SMART READ DATA
ec 00 01 00 00 00 00 00 00:30:26.677 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 00:30:26.675 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00:30:26.674 IDENTIFY DEVICE
Error 147 occurred at disk power-on lifetime: 35980 hours (1499 days + 4 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d4 00 03 4f c2 00 00 00:08:54.975 SMART EXECUTE OFF-LINE IMMEDIATE
b0 d0 01 00 4f c2 00 00 00:08:54.749 SMART READ DATA
ec 00 01 00 00 00 00 00 00:08:54.745 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 00:08:54.744 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00:08:54.742 IDENTIFY DEVICE
Error 146 occurred at disk power-on lifetime: 35970 hours (1498 days + 18 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d4 00 03 4f c2 00 00 03:23:55.527 SMART EXECUTE OFF-LINE IMMEDIATE
e3 00 00 00 00 00 40 00 03:23:55.527 IDLE
b0 d0 01 00 4f c2 00 00 03:23:55.299 SMART READ DATA
ec 00 01 00 00 00 00 00 03:23:55.296 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 03:23:55.294 IDENTIFY DEVICE
Error 145 occurred at disk power-on lifetime: 35969 hours (1498 days + 17 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d4 00 03 4f c2 00 00 02:45:47.564 SMART EXECUTE OFF-LINE IMMEDIATE
b0 d0 01 00 4f c2 00 00 02:45:47.333 SMART READ DATA
ec 00 01 00 00 00 00 00 02:45:47.329 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 02:45:47.328 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 02:45:47.326 IDENTIFY DEVICE
Error 144 occurred at disk power-on lifetime: 35966 hours (1498 days + 14 hours)
When the command that caused the error occurred, the device was in standby mod e.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f5 00 00 00 00 00 a0 00 00:35:34.430 SECURITY FREEZE LOCK
ef 66 00 00 00 00 a0 00 00:35:34.430 SET FEATURES [Disable revert defaul ts]
b1 c1 00 00 00 00 a0 00 00:35:34.429 DEVICE CONFIGURATION FREEZE LOCK [O BS-ACS-3]
f5 00 00 00 00 00 a0 00 00:35:34.429 SECURITY FREEZE LOCK
ef 10 06 00 00 00 a0 00 00:35:34.429 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error
# 1 Short offline Completed without error 00% 35980 -
# 2 Short offline Completed without error 00% 35980 -
# 3 Short offline Completed without error 00% 35980 -
# 4 Short offline Completed without error 00% 35969 -
# 5 Short offline Completed without error 00% 35967 -
# 6 Short offline Completed without error 00% 34227 -
# 7 Short offline Completed without error 00% 37 -
# 8 Short offline Completed without error 00% 31 -
# 9 Short offline Completed without error 00% 13 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
