disable commandline/console alerts

Grinas

Grinas

Contributor
Joined
May 4, 2017
Messages
174
I have a failed drive that i am waiting for a replacement to come but in the mean time i am getting alerts regularly when accessing truenas via SSH.

I do a lot of work on containers and access them via the shell so wondering is it possible to disable these as its making it a nightmare to work in the commandline.

here is an example of an alert
Code:
2024 Feb 12 19:45:43 truenas Device: /dev/sdd [SAT], 6 Currently unreadable (pending) sectors
 
Grinas

Grinas

Contributor
Joined
May 4, 2017
Messages
174
actually the drive that failed was replaced by the spare.

the drive that is showing Currently unreadable (pending) sectors is new.


Here are the smartctl results


Code:
smartctl -a /dev/sdd
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.63-production+truenas] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     ST10000VE001-3BX101
Serial Number:    WP00PJ2F
LU WWN Device Id: 5 000c50 0edac4c7b
Firmware Version: EV01
User Capacity:    10,000,831,348,736 bytes [10.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        Not in smartctl database 7.3/5319
ATA Version is:   ACS-4 (minor revision not indicated)
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Feb 13 08:57:12 2024 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  559) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 862) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x50bd) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   081   064   044    Pre-fail  Always       -       126566017
  3 Spin_Up_Time            0x0003   091   091   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       14
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   085   060   045    Pre-fail  Always       -       307503620
  9 Power_On_Hours          0x0032   096   096   000    Old_age   Always       -       4166
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       13
 18 Unknown_Attribute       0x000b   100   100   050    Pre-fail  Always       -       0
187 Reported_Uncorrect      0x0032   066   066   000    Old_age   Always       -       34
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       8590131203
190 Airflow_Temperature_Cel 0x0022   072   040   000    Old_age   Always       -       28 (Min/Max 24/30)
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       8
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1901
194 Temperature_Celsius     0x0022   028   060   000    Old_age   Always       -       28 (0 24 0 0 0)
197 Current_Pending_Sector  0x0012   100   085   000    Old_age   Always       -       6
198 Offline_Uncorrectable   0x0010   100   085   000    Old_age   Offline      -       6
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       4023 (20 193 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       105942459784
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       200985229471

SMART Error Log Version: 1
ATA Error Count: 46 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 46 occurred at disk power-on lifetime: 884 hours (36 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 ff ff ff 4f 00  31d+02:23:11.265  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  31d+02:23:10.264  WRITE FPDMA QUEUED
  61 00 10 30 01 00 40 00  31d+02:23:09.825  WRITE FPDMA QUEUED
  61 00 08 00 43 03 40 00  31d+02:23:09.752  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  31d+02:23:09.680  WRITE FPDMA QUEUED

Error 45 occurred at disk power-on lifetime: 884 hours (36 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 ff ff ff 4f 00  31d+02:23:08.553  WRITE FPDMA QUEUED
  61 00 08 00 43 03 40 00  31d+02:23:08.553  WRITE FPDMA QUEUED
  61 00 10 ff ff ff 4f 00  31d+02:23:08.553  WRITE FPDMA QUEUED
  60 00 80 ff ff ff 4f 00  31d+02:23:08.553  READ FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  31d+02:23:08.553  WRITE FPDMA QUEUED

Error 44 occurred at disk power-on lifetime: 879 hours (36 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 80 ff ff ff 4f 00  30d+21:03:16.383  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+21:03:15.862  WRITE FPDMA QUEUED
  61 00 80 ff ff ff 4f 00  30d+21:03:15.857  WRITE FPDMA QUEUED
  61 00 80 ff ff ff 4f 00  30d+21:03:15.856  WRITE FPDMA QUEUED
  61 00 80 ff ff ff 4f 00  30d+21:03:15.855  WRITE FPDMA QUEUED

Error 43 occurred at disk power-on lifetime: 877 hours (36 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 ff ff ff 4f 00  30d+19:21:04.056  WRITE FPDMA QUEUED
  61 00 08 00 43 03 40 00  30d+19:21:03.525  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+19:21:03.055  WRITE FPDMA QUEUED
  61 00 10 ff ff ff 4f 00  30d+19:21:03.034  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+19:21:02.678  WRITE FPDMA QUEUED

Error 42 occurred at disk power-on lifetime: 877 hours (36 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 08 00 43 03 40 00  30d+19:15:20.901  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+19:15:20.551  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+19:15:19.910  WRITE FPDMA QUEUED
  61 00 00 ff ff ff 4f 00  30d+19:15:19.731  WRITE FPDMA QUEUED
  60 00 80 ff ff ff 4f 00  30d+19:15:19.461  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Conveyance offline  Completed without error       00%        68         -
# 2  Extended offline    Completed without error       00%        13         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
You must log in or register to reply here.

Important Announcement for the TrueNAS Community.

The TrueNAS Community has now been moved. This forum will now become READ-ONLY for historical purposes. Please feel free to join us on the new TrueNAS Community Forums.

Related topics on forums.truenas.com for thread: "disable commandline/console alerts"

Similar threads

J
  • Locked
Possible Failing Drive Help
Replies
14
Views
4K
jbrown705
J
K
SMART Test
Replies
4
Views
1K
jgreco
jgreco
BitShepherd
Include timestamps with Email alerts (possible feature request)
Replies
2
Views
551
BitShepherd
BitShepherd
J
TrueNas Scale Alert - Don't Understand
Replies
3
Views
1K
Ebedorian
Ebedorian
E
  • Locked
Help me replace two drives... maybe.
Replies
2
Views
1K
BigDave
BigDave
Top