So I got a new server about a week ago, and I had installed TrueNAS.
I setup everything, and after a hour or two, it complained about the pool being degraded/faulted.
I rebooted, and when it ran the scrub again, it threw the error again.
In the Serial, it is showing "da6 CAM status SCSI Status Error. \SCSI status: Check Condition. \SCSI sense: ABORTED COMMAND (NAK received)."
I've tried searching to forums, and nothing I've seen has been of help.
What I have done is, swapped the 2 drives in that VDEV, the error did not follow the drive, but stayed in that da6 bay.
I then tried swapping the two HBA cables around with each other (because I don't have replacement cables) that go to the back of the backplane, the error stayed in that da6 bay as well. (I imagine it would have moved if it was the cables, or the controller).
I then just ordered a replacement backplane, and just now swapped that out, booted and it's STILL throwing errors.
I'm at a loss and would really appreciate any input. I'm a bit newer to servers, so please bear with me if I misuse any terminology or anything.
I have tried searching the forums, and have found many people with this issue, but nothing I've read has seemed to be of any help.
Thank you.
Specs:
Processor: 2x Intel Xeon E5-2630 V2 Hex (6) Core 2.6GHz (total 12 Cores)
Memory: 64GB DDR3 ECC REG
Hard Drives: 8x 4TB SAS3 12Gbps HGST Hitachi -HUS726040AL4210 (wired to SAS3 controller S3008-8LE)
Controller: 1x AOC-S3008-8LE SAS3 HBA Controller SET TO IT MODE (4 remaining slots are wired to on board SATA, currently only being used for boot SSD, the rest of the drives are using SAS. IT mode flashing was done by the company.)
NIC: * Integrated Quad Intel 1000BASE-T Ports
Server Chassis/ Case: Supermicro 2U CSE-826A-R1200LPB
Motherboard: X9DRi-LN4F+
Backplane: BPN-SAS-826A I-Path Direct Attached Backplane
PCI-Expansions slots: Low Profile 4 x16 PCI-E 3.0, 1 x8 PCI-E 3.0, 1 x4 PCI-E 3.0 (in x8)
Power: 2x 920Watt Power Supply PWS-920P-1R Platium (Only 1 in currently)
I setup everything, and after a hour or two, it complained about the pool being degraded/faulted.
I rebooted, and when it ran the scrub again, it threw the error again.
In the Serial, it is showing "da6 CAM status SCSI Status Error. \SCSI status: Check Condition. \SCSI sense: ABORTED COMMAND (NAK received)."
I've tried searching to forums, and nothing I've seen has been of help.
What I have done is, swapped the 2 drives in that VDEV, the error did not follow the drive, but stayed in that da6 bay.
I then tried swapping the two HBA cables around with each other (because I don't have replacement cables) that go to the back of the backplane, the error stayed in that da6 bay as well. (I imagine it would have moved if it was the cables, or the controller).
I then just ordered a replacement backplane, and just now swapped that out, booted and it's STILL throwing errors.
I'm at a loss and would really appreciate any input. I'm a bit newer to servers, so please bear with me if I misuse any terminology or anything.
I have tried searching the forums, and have found many people with this issue, but nothing I've read has seemed to be of any help.
Thank you.
Specs:
Processor: 2x Intel Xeon E5-2630 V2 Hex (6) Core 2.6GHz (total 12 Cores)
Memory: 64GB DDR3 ECC REG
Hard Drives: 8x 4TB SAS3 12Gbps HGST Hitachi -HUS726040AL4210 (wired to SAS3 controller S3008-8LE)
Controller: 1x AOC-S3008-8LE SAS3 HBA Controller SET TO IT MODE (4 remaining slots are wired to on board SATA, currently only being used for boot SSD, the rest of the drives are using SAS. IT mode flashing was done by the company.)
NIC: * Integrated Quad Intel 1000BASE-T Ports
Server Chassis/ Case: Supermicro 2U CSE-826A-R1200LPB
Motherboard: X9DRi-LN4F+
Backplane: BPN-SAS-826A I-Path Direct Attached Backplane
PCI-Expansions slots: Low Profile 4 x16 PCI-E 3.0, 1 x8 PCI-E 3.0, 1 x4 PCI-E 3.0 (in x8)
Power: 2x 920Watt Power Supply PWS-920P-1R Platium (Only 1 in currently)