twillkickers
Dabbler
- Joined
- Jun 3, 2017
- Messages
- 19
I am running Freenas 11.1-Stable.
I have recently got alerts that both drives in my array seem to have an unusually high error count. I am new to this whole NAS thing and so my knowledge is very limited. Should I be concerned? What might be causing my errors? I have placed smartctl -a output for both of my drives below. I appreciate any help! (Sorry for my limited knowledge.)
Output of smartctl -a for first drive:
Output of smartctl -a for second drive:
What might be going on? I am using Western Digital Black drives, are these inappropriate for RAID storage? Once again, thanks for any help.
I have recently got alerts that both drives in my array seem to have an unusually high error count. I am new to this whole NAS thing and so my knowledge is very limited. Should I be concerned? What might be causing my errors? I have placed smartctl -a output for both of my drives below. I appreciate any help! (Sorry for my limited knowledge.)
Output of smartctl -a for first drive:
Code:
=== START OF INFORMATION SECTION === Model Family: Western Digital Black Device Model: WDC WD5001FZWX-00ZHUA0 Serial Number: WD-WX31DC46JJUF LU WWN Device Id: 5 0014ee 0041be98d Firmware Version: 01.01A01 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 6 11:21:14 2018 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 90) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 542) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 229 100 021 Pre-fail Always - 7541 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1944 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 100 000 Old_age Always - 0 9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18518 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 148 192 Power-Off_Retract_Count 0x0032 200 100 000 Old_age Always - 94 193 Load_Cycle_Count 0x0032 200 100 000 Old_age Always - 1850 194 Temperature_Celsius 0x0022 106 097 000 Old_age Always - 46 196 Reallocated_Event_Count 0x0032 200 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 100 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 209 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 209 occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 10 88 75 d2 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 208 occurred at disk power-on lifetime: 18507 hours (771 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 50 80 39 d0 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 207 occurred at disk power-on lifetime: 18414 hours (767 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 f0 f8 56 86 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 206 occurred at disk power-on lifetime: 18172 hours (757 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 32 c7 71 01 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 34d+02:41:59.482 SET FEATURES [Enable SATA feature] Error 205 occurred at disk power-on lifetime: 18158 hours (756 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 32 c7 71 01 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 33d+13:09:34.957 SET FEATURES [Enable SATA feature] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 18507 - # 2 Extended offline Completed without error 00% 14473 - # 3 Short offline Completed without error 00% 14441 - # 4 Extended offline Completed without error 00% 14430 - # 5 Short offline Completed without error 00% 14421 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Output of smartctl -a for second drive:
Code:
=== START OF INFORMATION SECTION === Model Family: Western Digital Black Device Model: WDC WD5001FZWX-00ZHUA0 Serial Number: WD-WX21D955YUA1 LU WWN Device Id: 5 0014ee 0aec7d3e0 Firmware Version: 01.01A01 User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 6 11:24:39 2018 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 90) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 559) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 229 100 021 Pre-fail Always - 7533 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1028 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 100 000 Old_age Always - 0 9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 17763 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 144 192 Power-Off_Retract_Count 0x0032 200 100 000 Old_age Always - 85 193 Load_Cycle_Count 0x0032 200 100 000 Old_age Always - 943 194 Temperature_Celsius 0x0022 108 098 000 Old_age Always - 44 196 Reallocated_Event_Count 0x0032 200 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 100 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 1426 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1426 occurred at disk power-on lifetime: 17706 hours (737 days + 18 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 08 30 f8 a4 40 Error: Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 1425 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 1424 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 1423 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- Error 1422 occurred at disk power-on lifetime: 17417 hours (725 days + 17 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 00% 0 - # 2 Extended offline Completed without error 00% 13698 - # 3 Short offline Completed without error 00% 13686 - # 4 Extended offline Completed without error 00% 13675 - # 5 Short offline Completed without error 00% 13665 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
What might be going on? I am using Western Digital Black drives, are these inappropriate for RAID storage? Once again, thanks for any help.
