Assistance sur message security output

[profwalken]

Bonjour,
j'ai un serveur freenas 9.3 , avec 4 G de ram, 2 disques WD Red 2To montés en mirroir via ZFS.
L'install de freenas est faite sur une carte compact Flash connetés en IDE via adaptateur.

depuis quelques jours je reçois un mail "security output" avec le contenu suivant :
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 50 68 00 18 18 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 50 68 00 18 18 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 50 68 00 18 18 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 50 68 00 18 18 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 50 68 00 18 18 00 00 01 00
(ada0:ata0:0:0:0): Error 5, Retries exhausted
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 02 02 b8 07 07 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 02 02 b8 07 07 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 02 02 b8 07 07 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 02 02 b8 07 07 00 00 01 00
(ada0:ata0:0:0:0): Retrying command
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): CAM status: ATA Status Error
(ada0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada0:ata0:0:0:0): RES: 51 04 02 02 b8 07 07 00 00 01 00
(ada0:ata0:0:0:0): Error 5, Retries exhausted
(ada0:ata0:0:0:0): DSM TRIM. ACB: 06 01 00 00 00 40 00 00 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 32 18 00 22 22 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 32 18 00 22 22 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 32 18 00 22 22 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 32 18 00 22 22 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 32 18 00 22 22 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 e8 0a e1 62 62 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 e8 0a e1 62 62 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 e8 0a e1 62 62 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 e8 0a e1 62 62 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 e8 0a e1 62 62 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 15 0f 00 02 02 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 15 0f 00 02 02 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 15 0f 00 02 02 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 15 0f 00 02 02 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 15 0f 00 02 02 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 80 c8 00 13 13 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 80 c8 00 13 13 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 80 c8 00 13 13 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 80 c8 00 13 13 00 00 01 00
(ada0:ata0:0:0:0): RES: 51 04 80 c8 00 13 13 00 00 01 00

-- End of security output --

Qui peut me dire comment interpréter ces messages ? est ce que la carte CF est entrain de lacher? si oui, puis facilement réinstaller freenas sur une clé USB à la place?

Merci pour votre aide,
Cordialement,
Profwalken

 

[Bidule0hm]

Tu as seulement la moitié de la quantité de RAM minimum et il est fortement déconseillé d'installer FreeNAS sur autre chose qu'une clé USB ou qu'un périphérique SATA natif (DOM, SSD, HDD, ... mais pas d'adaptateur SATA/IDE, SATA/CF, SATA/SD, ...) donc il est très probable que ton problème vienne de là ;)

 

[profwalken]

Merci pour la réponse, qui m'en amène une autre, comment procéder à la réinstallation de freenas sur une clé usb.
dois je simplement sauvegarder la config, areter le pc et virer la CF, puis mettre une clé usb, installer la meme version de freenas puis restaurer la config.
Est ce la bonne méthode pour faire ce changement de support pour freenas ?

Merci pour votre confirmation ou pas de ce process.

 

[Bidule0hm]

Oui, c'est exactement ça ;)

Je re-rappel qu'avoir seulement 4 Go de RAM peut mener à de gros pb (incluant la perte de tes données), plusieurs membres l'ont vécu et n'avaient pas de sauvegarde. Ne soit pas étonné si ça t'arrive et ne soit pas étonné non plus si tu ne trouve personne pour t'aider (tous les membres un tant soit peu expérimentés savent qu'à ce stade on ne peut plus rien pour récupérer les données). Je peux paraître lourd mais si ça peut sauver tes données...

 

[profwalken]

Merci pour le conseil, il me semble que ma carte mère ne supporte pas plus de 8go sur les 2 slots dispo et je ne pense pas que ce soit possible de mettre des modules ECC

 

[profwalken]

Bonjour , J'ai de nouveau un long message security run output suite à la mise en place des dernières mises à jour.
Comment savoir si quelque chose d'important est signalé dans ces remontées d'infos ?

Détail du message:
SRV-SATURNE.local changes in mounted filesystems:
35c35
< freenas-boot/ROOT/FreeNAS-9.3-STABLE-201512121950 / zfs rw,noatime,nfsv4acls 0 0
---

freenas-boot/ROOT/FreeNAS-9.3-STABLE-201601181840 / zfs rw,noatime,nfsv4acls 0 0

SRV-SATURNE.local kernel log messages:

Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.3-RELEASE-p31 #0 r288272+81e2595: Mon Jan 18 10:48:44 PST 2016
root@build3.ixsystems.com:/tank/home/stable-builds/FN/objs/os-base/amd64/tank/home/stable-builds/FN/FreeBSD/src/sys/FREENAS.amd64 amd64
gcc version 4.2.1 20070831 patched [FreeBSD]
CPU: Intel(R) Atom(TM) CPU C2750 @ 2.40GHz (2400.06-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x406d8 Family = 0x6 Model = 0x4d Stepping = 8
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x43d8e3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,RDRAND>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x101<LAHF,Prefetch>
Standard Extended Features=0x2282<TSCADJ,SMEP,ENHMOVSB>
TSC: P-state invariant, performance statistics
real memory = 17985175552 (17152 MB)
avail memory = 16490123264 (15726 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <INTEL TIANO >
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 8 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 2
cpu2 (AP): APIC ID: 4
cpu3 (AP): APIC ID: 6
cpu4 (AP): APIC ID: 8
cpu5 (AP): APIC ID: 10
cpu6 (AP): APIC ID: 12
cpu7 (AP): APIC ID: 14
WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.
ACPI Warning: FADT (revision 5) is longer than ACPI 5.0 version, truncating length 268 to 256 (20111123/tbfadt-325)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
aesni0: <AES-CBC,AES-XTS> on motherboard
padlock0: No ACE support.
acpi0: <ALASKA A M I > on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> mem 0xdf640000-0xdf65ffff irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> mem 0xdf620000-0xdf63ffff irq 20 at device 3.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> mem 0xdf400000-0xdf41ffff irq 22 at device 0.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <PCI-PCI bridge> irq 23 at device 1.0 on pci3
pci4: <PCI bus> on pcib4
ahci0: <Marvell 88SE9172 AHCI SATA controller> port 0xc040-0xc047,0xc030-0xc033,0xc020-0xc027,0xc010-0xc013,0xc000-0xc00f mem 0xdf310000-0xdf3101ff irq 23 at device 0.0 on pci4
ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pcib5: <PCI-PCI bridge> irq 23 at device 5.0 on pci3
pci5: <PCI bus> on pcib5
pcib6: <PCI-PCI bridge> irq 23 at device 0.0 on pci5
pci6: <PCI bus> on pcib6
vgapci0: <VGA-compatible display> port 0xb000-0xb07f mem 0xde000000-0xdeffffff,0xdf000000-0xdf01ffff irq 23 at device 0.0 on pci6
vgapci0: Boot video device
pcib7: <PCI-PCI bridge> irq 21 at device 7.0 on pci3
pci7: <PCI bus> on pcib7
igb0: <Intel(R) PRO/1000 Network Connection version - 2.4.0> port 0xa000-0xa01f mem 0xdf200000-0xdf27ffff,0xdf280000-0xdf283fff irq 21 at device 0.0 on pci7
igb0: Using MSIX interrupts with 5 vectors
igb0: Ethernet address: d0:50:99:c0:05:96
igb0: Bound queue 0 to cpu 0
igb0: Bound queue 1 to cpu 1
igb0: Bound queue 2 to cpu 2
igb0: Bound queue 3 to cpu 3
pcib8: <PCI-PCI bridge> irq 23 at device 9.0 on pci3
pci8: <PCI bus> on pcib8
pcib9: <ACPI PCI-PCI bridge> mem 0xdf600000-0xdf61ffff at device 4.0 on pci0
pci9: <ACPI PCI bus> on pcib9
ahci1: <Marvell 88SE9230 AHCI SATA controller> port 0xd050-0xd057,0xd040-0xd043,0xd030-0xd037,0xd020-0xd023,0xd000-0xd01f mem 0xdf510000-0xdf5107ff irq 23 at device 0.0 on pci9
ahci1: AHCI v1.20 with 8 6Gbps ports, Port Multiplier not supported
ahci1: quirks=0x900<NOBSYRES,ALTSIG>
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
ahcich8: <AHCI channel> at channel 6 on ahci1
ahcich9: <AHCI channel> at channel 7 on ahci1
ehci0: <Intel Avoton USB 2.0 controller> mem 0xdf663000-0xdf6633ff irq 23 at device 22.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
ahci2: <Intel Avoton AHCI SATA controller> port 0xe0d0-0xe0d7,0xe0c0-0xe0c3,0xe0b0-0xe0b7,0xe0a0-0xe0a3,0xe040-0xe05f mem 0xdf662000-0xdf6627ff irq 19 at device 23.0 on pci0
ahci2: AHCI v1.30 with 4 3Gbps ports, Port Multiplier not supported
ahcich10: <AHCI channel> at channel 0 on ahci2
ahcich11: <AHCI channel> at channel 1 on ahci2
ahcich12: <AHCI channel> at channel 2 on ahci2
ahcich13: <AHCI channel> at channel 3 on ahci2
ahci3: <Intel Avoton AHCI SATA controller> port 0xe090-0xe097,0xe080-0xe083,0xe070-0xe077,0xe060-0xe063,0xe020-0xe03f mem 0xdf661000-0xdf6617ff irq 19 at device 24.0 on pci0
ahci3: AHCI v1.30 with 2 6Gbps ports, Port Multiplier not supported
ahcich14: <AHCI channel> at channel 0 on ahci3
ahcich15: <AHCI channel> at channel 1 on ahci3
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart2: <16550 or compatible> port 0x248-0x24f irq 3 on acpi0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: CGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3d0-0x3db iomem 0xb8000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
wbwd0: DevID 0xc3 DevRev 0x33, will not attach, please report this.
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
coretemp4: <CPU On-Die Thermal Sensors> on cpu4
est4: <Enhanced SpeedStep Frequency Control> on cpu4
coretemp5: <CPU On-Die Thermal Sensors> on cpu5
est5: <Enhanced SpeedStep Frequency Control> on cpu5
coretemp6: <CPU On-Die Thermal Sensors> on cpu6
est6: <Enhanced SpeedStep Frequency Control> on cpu6
coretemp7: <CPU On-Die Thermal Sensors> on cpu7
est7: <Enhanced SpeedStep Frequency Control> on cpu7
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to accept, logging disabled
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
uhub0: 8 ports with 8 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub1: <vendor 0x8087 product 0x07db, class 9/0, rev 2.00/0.02, addr 2> on usbus0
uhub1: 4 ports with 4 removable, self powered
ugen0.3: <vendor 0x1a40> at usbus0
uhub2: <vendor 0x1a40 USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 3> on usbus0
uhub2: MTT enabled
uhub2: 7 ports with 7 removable, self powered
ugen0.4: <SanDisk> at usbus0
umass0: <SanDisk Cruzer Fit, class 0/0, rev 2.00/1.27, addr 4> on usbus0
umass0: SCSI over Bulk-Only; quirks = 0x8100
umass0:17:0:-1: Attached to scbus17
ugen0.5: <vendor 0x058f> at usbus0
umass1: <vendor 0x058f USB Reader, class 0/0, rev 1.10/1.00, addr 5> on usbus0
umass1: SCSI over Bulk-Only; quirks = 0x4001
umass1:18:1:-1: Attached to scbus18
ugen0.6: <American Megatrends Inc.> at usbus0
uhub3: <7-port Hub> on usbus0
uhub3: 5 ports with 5 removable, self powered
ugen0.7: <American Megatrends Inc.> at usbus0
ukbd0: <Keyboard Interface> on usbus0
kbd2 at ukbd0
ums0: <Mouse Interface> on usbus0
ums0: 3 buttons and [Z] coordinates ID=0
da0 at umass-sim0 bus 0 scbus17 target 0 lun 0
da0: <SanDisk Cruzer Fit 1.27> Removable Direct Access SCSI-6 device
da0: Serial Number 4C530006070819110192
da0: 40.000MB/s transfers
da0: 15267MB (31266816 512 byte sectors: 255H 63S/T 1946C)
da0: quirks=0x2<NO_6_BYTE>
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <WDC WD10EFRX-68JCSN0 01.01A01> ATA-8 SATA 3.x device
ada0: Serial Number WD-WCC1U4961652
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada0: quirks=0x1<4K>
ada0: Previously was known as ad4
ada1 at ahcich14 bus 0 scbus14 target 0 lun 0
cd0 at ahcich5 bus 0 scbus5 target 0 lun 0
cd0: <HL-DT-ST DVDRAM GH40F MG01> Removable CD-ROM SCSI-0 device
cd0: Serial Number EA7CAAC57CEB
cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
ada1: <WDC WD30EFRX-68EUZN0 82.00A82> ATA-9 SATA 3.x device
ada1: Serial Number WD-WCC4N3CYKK5T
ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada1: quirks=0x1<4K>
ada1: Previously was known as ad32
ada2 at ahcich15 bus 0 scbus15 target 0 lun 0
ada2: <WDC WD10EFRX-68JCSN0 01.01A01> ATA-8 SATA 3.x device
ada2: Serial Number WD-WCC1U4799412
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2: Previously was known as ad34
pass2 at ahcich9 bus 0 scbus9 target 0 lun 0
pass2: <Marvell Console 1.01> Removable Processor SCSI-0 device
pass2: Serial Number HKDP221516WL
pass2: 150.000MB/s transfers (SATA 1.x, UDMA4, ATAPI 12bytes, PIO 8192bytes)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #7 Launched!
Timecounter "TSC-low" frequency 1200029124 Hz quality 1000
da1 at umass-sim1 bus 1 scbus18 target 0 lun 0
da1: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device
da1: Serial Number 9205291
da1: 1.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
da1: quirks=0x2<NO_6_BYTE>
da2 at umass-sim1 bus 1 scbus18 target 0 lun 1
da2: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device
da2: Serial Number 9205291
da2: 1.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
da2: quirks=0x2<NO_6_BYTE>
da3 at umass-sim1 bus 1 scbus18 target 0 lun 2
da3: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device
da3: Serial Number 9205291
da3: 1.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
da3: quirks=0x2<NO_6_BYTE>
da4 at umass-sim1 bus 1 scbus18 target 0 lun 3
da4: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device
da4: Serial Number 9205291
da4: 1.000MB/s transfers
da4: Attempt to query device size failed: NOT READY, Medium not present
da4: quirks=0x2<NO_6_BYTE>
Trying to mount root from zfs:freenas-boot/ROOT/FreeNAS-9.3-STABLE-201601181840 []...
GEOM_RAID5: Module loaded, version 1.3.20140711.62 (rev f91e28e40bf7)
ipmi0: <IPMI System Interface> port 0xca2,0xca3 on acpi0
ipmi0: KCS mode found at io 0xca2 on acpi
ipmi0: IPMI device rev. 1, firmware rev. 0.23, version 2.0
ipmi0: Number of channels 2
ipmi0: Attached watchdog
wbwd0: DevID 0xc3 DevRev 0x33, will not attach, please report this.
GEOM_ELI: Device ada1p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI: Crypto: hardware
GEOM_ELI: Device ada0p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI: Crypto: hardware
GEOM_ELI: Device ada2p1.eli created.
GEOM_ELI: Encryption: AES-XTS 256
GEOM_ELI: Crypto: hardware
vboxdrv: fAsync=0 offMin=0x558 offMax=0x1578
bridge0: Ethernet address: 02:52:76:de:ab:00
igb0: promiscuous mode enabled
bridge0: link state changed to UP
epair0a: Ethernet address: 02:42:b2:00:06:0a
epair0b: Ethernet address: 02:42:b2:00:07:0b
epair0a: link state changed to UP
epair0b: link state changed to UP
igb0: link state changed to DOWN
epair0a: promiscuous mode enabled
ng_ether_ifnet_arrival_event: can't re-name node epair0b
igb0: link state changed to UP
epair1a: Ethernet address: 02:03:28:00:07:0a
epair1b: Ethernet address: 02:03:28:00:08:0b
epair1a: link state changed to UP
epair1b: link state changed to UP
epair1a: promiscuous mode enabled
ng_ether_ifnet_arrival_event: can't re-name node epair1b
ipmi0: KCS: Reply address mismatch
ipmi0: KCS error: 5f
ipmi0: KCS: Reply address mismatch
ipmi0: KCS error: 5f
ipmi0: KCS: Reply address mismatch
ipmi0: KCS error: 5f
ipmi0: Failed to reset watchdog

-- End of security output --


-----
Aucun virus trouvé dans ce message.
Analyse effectuée par AVG - www.avg.fr
Version: 2016.0.7294 / Base de données virale: 4522/11441 - Date: 19/01/2016