xdddxxmx
Cadet
- Joined
- May 8, 2023
- Messages
- 4
Hi guys,
I'm using TrueNAS Core 13.0-U4 version.
The UPS I'm using is the LADIS(雷迪司) H2000.
The drivers I'm using are: blazer_usb or nutdrv_qx.
The port is set to "auto".
Initially, the driver is detected and the shutdown signal is sent correctly. The system shuts down automatically, and everything appears to be working fine.
When I use the command "upsc ups@localhost" to check the results, I get the following:
However, after 5-10 minutes, sometimes even 2-3 minutes, I start seeing the following message on the console:
And it keeps refreshing every 4-5 seconds.
I also receive emails with the following content:
And another email:
A few minutes later, I receive an email with the following content:
At this point, when I use the command "upsc ups@localhost" again, I get feedback that the driver is not active.
Restarting the UPS service or using the "upsdrvctl start" command restores it to the initial working state. Using "upsc ups@localhost" also provides the correct feedback. However, after waiting a few minutes, the same issue reappears.
I have already tried:
Using a different USB port.
Saving the UPS configuration again.
Downgrading to TrueNAS Core 13.0-U3.1.
Changing the USB cable.
Trying different drivers.
But the problem persists.
Do you have any suggestions on how to resolve this?
Thanks!!
I'm using TrueNAS Core 13.0-U4 version.
The UPS I'm using is the LADIS(雷迪司) H2000.
The drivers I'm using are: blazer_usb or nutdrv_qx.
The port is set to "auto".
Initially, the driver is detected and the shutdown signal is sent correctly. The system shuts down automatically, and everything appears to be working fine.
When I use the command "upsc ups@localhost" to check the results, I get the following:
Code:
battery.charge: 83
battery.voltage: 25.10
battery.voltage.high: 26.00
battery.voltage.low: 20.80
battery.voltage.nominal: 24.0
device.type: ups
driver.name: blazer_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.synchronous: no
driver.version: 2.7.4
driver.version.internal: 0.12
input.current.nominal: 8.0
input.frequency: 50.1
input.frequency.nominal: 50
input.voltage: 232.9
input.voltage.fault: 235.0
input.voltage.nominal: 220
output.voltage: 232.9
ups.beeper.status: enabled
ups.delay.shutdown: 30
ups.delay.start: 180
ups.load: 28
ups.productid: 5161
ups.status: OL
ups.type: offline / line interactive
ups.vendorid: 066
However, after 5-10 minutes, sometimes even 2-3 minutes, I start seeing the following message on the console:
Code:
May 11 19:13:44 truenas 1 2023-05-11T19:13:44.169087+08:88 truenas.local upsmon 3920 - - Poll UPS [ups@localhost:3493] failed - Driver not connected
And it keeps refreshing every 4-5 seconds.
I also receive emails with the following content:
TrueNAS truenas.local: Alerts
TrueNAS @ truenas.local
New alerts:
Communication with UPS ups lost.
Current alerts:
Communication with UPS ups lost.
And another email:
TrueNAS truenas.local: UPS report generated by truenas.local
NOTIFICATION: 'COMMBAD'
UPS: 'ups'
Statistics could not be recovered.
A few minutes later, I receive an email with the following content:
I receive an email with the subject "Statistics could not be recovered" every 5 minutes.TrueNAS truenas.local: Alerts
TrueNAS @ truenas.local
The following alert has been cleared:
Communication with UPS ups lost.
At this point, when I use the command "upsc ups@localhost" again, I get feedback that the driver is not active.
Code:
Error: Driver not connected
Restarting the UPS service or using the "upsdrvctl start" command restores it to the initial working state. Using "upsc ups@localhost" also provides the correct feedback. However, after waiting a few minutes, the same issue reappears.
I have already tried:
Using a different USB port.
Saving the UPS configuration again.
Downgrading to TrueNAS Core 13.0-U3.1.
Changing the USB cable.
Trying different drivers.
But the problem persists.
Do you have any suggestions on how to resolve this?
Thanks!!