Hi,
For some reason, FreeNAS won't recognise the disks connected to the SAS controller (SATA disks, WD Re attached).
Version:
FreeNAS-11.0-U2 (e417d8aa5)
Motherboard:
X10SDV-4C-7TP4F board with a SAS826TQ backplane in a Supermicro chassis.
Controller
LSI SAS2116
dmesg points me in some direction, however i have no idea how to interpret this:
In the motherboard is a LSI SAS2116 controller with firmware P19, that's the latest that Supermicro provides:
ftp://ftp.supermicro.nl/driver/SAS/LSI/2116/Firmware/IT/
I'm stuck.. Anyone?
For some reason, FreeNAS won't recognise the disks connected to the SAS controller (SATA disks, WD Re attached).
Version:
FreeNAS-11.0-U2 (e417d8aa5)
Motherboard:
X10SDV-4C-7TP4F board with a SAS826TQ backplane in a Supermicro chassis.
Controller
LSI SAS2116
dmesg points me in some direction, however i have no idea how to interpret this:
Code:
root@freenas:~ # dmesg | grep mps mps0: <Avago Technologies (LSI) SAS2116> port 0xe000-0xe0ff mem 0xfb5c0000-0xfb5c3fff,0xfb580000-0xfb5bffff irq 16 at device 0.0 on pci3 mps0: Firmware: 19.00.02.00, Driver: 21.01.00.00-fbsd mps0: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc> mps_mapping_enclosure_dev_status_change_event: enclosure with handle = 0x1 reported 0 slots mps0: SAS Address for SATA device = a2984a22a7bdc971 mps0: SAS Address from SATA device = a2984a22a7bdc971 failure at /freenas-11-releng/freenas/_BE/os/sys/dev/mps/mps_sas_lsi.c:675/mpssas_add_device()! Could not get ID for device with handle 0x0011 mpssas_fw_work: failed to add device with handle 0x11 mps0: SAS Address for SATA device = a2984a1fc7cfb190 mps0: SAS Address from SATA device = a2984a1fc7cfb190 failure at /freenas-11-releng/freenas/_BE/os/sys/dev/mps/mps_sas_lsi.c:675/mpssas_add_device()! Could not get ID for device with handle 0x0012 mpssas_fw_work: failed to add device with handle 0x12 mps0: SAS Address for SATA device = a2984a23c6a7c587 mps0: SAS Address from SATA device = a2984a23c6a7c587 failure at /freenas-11-releng/freenas/_BE/os/sys/dev/mps/mps_sas_lsi.c:675/mpssas_add_device()! Could not get ID for device with handle 0x0013 mpssas_fw_work: failed to add device with handle 0x13 mps0: SAS Address for SATA device = a2984a26c5cfd174 mps0: SAS Address from SATA device = a2984a26c5cfd174 failure at /freenas-11-releng/freenas/_BE/os/sys/dev/mps/mps_sas_lsi.c:675/mpssas_add_device()! Could not get ID for device with handle 0x0014 mpssas_fw_work: failed to add device with handle 0x14
Code:
root@freenas:~ # sas2ircu 0 DISPLAY LSI Corporation SAS2 IR Configuration Utility. Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved. Read configuration has been initiated for controller 0 ------------------------------------------------------------------------ Controller information ------------------------------------------------------------------------ Controller type : SAS2116_1 BIOS version : 7.37.01.00 Firmware version : 19.00.02.00 Channel description : 1 Serial Attached SCSI Initiator ID : 0 Maximum physical devices : 125 Concurrent commands supported : 1720 Slot : 11 Segment : 0 Bus : 2 Device : 0 Function : 0 RAID Support : No Disk info below, cut out..
In the motherboard is a LSI SAS2116 controller with firmware P19, that's the latest that Supermicro provides:
ftp://ftp.supermicro.nl/driver/SAS/LSI/2116/Firmware/IT/
I'm stuck.. Anyone?