Replace Drive with Spare

[turboaaa]

This was a new raidz2 build. I had a drive fail, it was replaced, but I made the mistake of setting it up as a spare instead of replacing the existing drive in the pool. Not the worst thing to happen but now I have an annoying warning light that the pool is degraded. Is there any possibility that I can convert the spare into an actual replacement without rebuilding everything? At this point the pool is in use.

Sorry for the stupid question, I knew better than this.

Code:

  pool: tank
 state: DEGRADED
status: One or more devices has been taken offline by the administrator.
	Sufficient replicas exist for the pool to continue functioning in a
	degraded state.
action: Online the device using 'zpool online' or replace the device with
	'zpool replace'.
  scan: resilvered 1.57M in 0 days 00:00:00 with 0 errors on Sat May 26 17:44:38 2018
config:

	NAME											  STATE	 READ WRITE CKSUM
	tank											  DEGRADED	 0	 0	 0
	  raidz2-0										DEGRADED	 0	 0	 0
		gptid/ca363e73-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/cca8828b-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/d1b86990-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/d51049fe-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/d804819b-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/db20f312-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/dda24b58-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/e11d1f00-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		gptid/e39e8936-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
		spare-9									   DEGRADED	 0	 0	 0
		  17637264324123775223						OFFLINE	  0	 0	 0  was /dev/gptid/e55c7104-5d4d-11e8-aaf6-002590fde644
		  gptid/051c5d74-612e-11e8-8357-002590fde644  ONLINE	   0	 0	 0
		gptid/e837b4dd-5d4d-11e8-aaf6-002590fde644	ONLINE	   0	 0	 0
	logs
	  gptid/4a426d0c-612b-11e8-8357-002590fde644	  ONLINE	   0	 0	 0
	spares
	  227308045836062793							  INUSE	 was /dev/gptid/051c5d74-612e-11e8-8357-002590fde644

errors: No known data errors

 

[kdragon75]

Yeah, I dont see anything taking a glance at the Oracle docs. I would think there's a way without offline/remove...
On a side note, most people here seem to prefer cold or even warm spares rather than the automatic hot spare for manageability.

 

[turboaaa]

Yeah, I don't see anything taking a glance at the Oracle docs. I would think there's a way without offline/remove...
On a side note, most people here seem to prefer cold or even warm spares rather than the automatic hot spare for manageability.

Yeah, the pool was built without a spare but then I added the replacement drive as one. What I get for multitasking and not paying closer attention.

 

[turboaaa]

Found the solution for this; simple take the spare offline, remove it from the pool, then replace the failed drive with the one used as the spare. Blinking red light gone!