Junicast
Patron
- Joined
- Mar 6, 2015
- Messages
- 206
Greetings,
I've had a power outage which might have bricked some devices. An Access Point for example is broken as are Mainboard / CPU / RAM.
So I put older Motherboard in with i7 2600 GA-H77 Gigabyte with 16 GB of RAM non ECC.
There are five spinning HDD with size of 4 TB each. In each device shows up as {ada0..ada4}.
FreeNAS-11.2-U4.1 is running on an USB flash drive which boots fine. Host gets up with correct IP and stuff but Pool is encrypted. I try to decrypt but the error pops up. I finally decide to
1. backup config with recovery key of zpool
2. detach pool
3. reimport encrypted pool with uploading key and giving password
When it comes to where I have to select the Pool from dropdown men it just doesn't show anything (screenshot).
I can't pull the menu open. When I enter only the boot pool shows up.
I've also tried a different backup of encryption key of pool but same problem.
This show up in middlewared.log when I hit next in the wizard.
Any ideas on this?
I suspect drives might also be in jeopardy. I just started long smartctl tests on each drive. So far none of the disks have had any sector reallocated so far. Hope I can get it mounted again :)
Wish me luck
I've had a power outage which might have bricked some devices. An Access Point for example is broken as are Mainboard / CPU / RAM.
So I put older Motherboard in with i7 2600 GA-H77 Gigabyte with 16 GB of RAM non ECC.
There are five spinning HDD with size of 4 TB each. In
Code:
geom disk list
FreeNAS-11.2-U4.1 is running on an USB flash drive which boots fine. Host gets up with correct IP and stuff but Pool is encrypted. I try to decrypt but the error
Code:
Code Code
1. backup config with recovery key of zpool
2. detach pool
3. reimport encrypted pool with uploading key and giving password
When it comes to where I have to select the Pool from dropdown men it just doesn't show anything (screenshot).
I can't pull the menu open. When I enter
Code:
zpool status
I've also tried a different backup of encryption key of pool but same problem.
This show up in middlewared.log when I hit next in the wizard.
Code:
[2019/09/26 20:30:17] (DEBUG) middleware.notifier.geli_attach_single():598 - gptid/3c38d05a-2ac4-11e7-97e2-001b21c1a8c0 already attached [2019/09/26 20:30:17] (DEBUG) middleware.notifier.geli_attach_single():598 - gptid/4076a268-2ac4-11e7-97e2-001b21c1a8c0 already attached [2019/09/26 20:30:17] (DEBUG) middleware.notifier.geli_attach_single():598 - gptid/6a727f00-94df-11e9-a437-001b21c1a8c0 already attached [2019/09/26 20:30:17] (DEBUG) middleware.notifier.geli_attach_single():598 - gptid/1e54548e-9534-11e9-b085-001b21c1a8c0 already attached [2019/09/26 20:30:17] (DEBUG) middleware.notifier.geli_attach_single():598 - gptid/5ac3ea5a-9451-11e9-a437-001b21c1a8c0 already attached
Any ideas on this?
I suspect drives might also be in jeopardy. I just started long smartctl tests on each drive. So far none of the disks have had any sector reallocated so far. Hope I can get it mounted again :)
Wish me luck
Attachments
Last edited: