Local daily security run output-do I need to worry?

Status
Not open for further replies.
C

Ceetan

Contributor
Joined
Apr 29, 2016
Messages
139
We have something of a heat wave in Stockholm at the moment. This caused my server to run the fans at full speed yesterday. This is ultimately a good thing, though the noise was a bit annoying. For other reasons, am I allowed it to go through a reboot yesterday evening. No I get this output from the local daily security notification. Should I be worried? I already know about the IPMI KCS Error, and I’ll see what I can do about it, but is there anything more I should be worried about?



Code:
Darwin.local kernel log messages:
> CPU: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz (3696.15-MHz K8-class CPU)
> Timecounter "TSC-low" frequency 1848072727 Hz quality 1000
> ugen0.1: <0x8086 XHCI root HUB> at usbus0
> mpr0: Found device <881<SataDev,Direct>,End Device> <6.0Gbps> handle<0x000a> enclosureHandle<0x0001> slot 1
> mpr0: At enclosure level 0 and connector name (	)
> uhub0: mpr0: SAS Address from SAS device page0 = 4433221102000000
> <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
> ada0: da0 at mpr0 bus 0 scbus0 target 0 lun 0
> <Corsair CSSD-F90GB2 2.0> ATA8-ACS SATA 2.x device
> da6 at mpr0 bus 0 scbus0 target 6 lun 0
> da6: <ATA WDC WD40EFRX-68W 0A82> Fixed Direct Access SPC-4 SCSI device
> da6: Serial Number WD-WCC4E3YFJ8SF
> da6: 600.000MB/s transfers
> da6: Command Queueing enabled
> da6: 3815447MB (7814037168 512 byte sectors)
> da6: quirks=0x8<4K>
> da7 at mpr0 bus 0 scbus0 target 7 lun 0
> da7: <ATA WDC WD40EFRX-68W 0A82> Fixed Direct Access SPC-4 SCSI device
> da7: Serial Number WD-WCC4E3YFJZ8N
> da7: 600.000MB/s transfers
> da7: Command Queueing enabled
> da7: 3815447MB (7814037168 512 byte sectors)
> da7: quirks=0x8<4K>
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> ipmi0: uhub1: at uhub0, port 12, addr 2 (disconnected)
> KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 3 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 3 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 4 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 4> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 5> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 5> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 5 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 5 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 6> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 6> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff

-- End of security output --

 
Ericloewe

Ericloewe

Server Wrangler
Moderator
Joined
Feb 15, 2014
Messages
20,194
That's just because of the reboot. Nothing to worry about, unless the reboot itself is cause for concern.
 
C

Ceetan

Contributor
Joined
Apr 29, 2016
Messages
139
I think I am going to necro this one, because what happened now seems to be very similar.

Is it similar, or have I missed something?
Code:
Darwin.local kernel log messages:
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 9 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 8 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 8 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 12 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 12> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 10> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 10> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 10 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 10 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 11> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 11> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 12 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 11 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 11 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 15 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 15> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 13> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 13> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 13 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 13 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 14> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 14> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> ipmi0: uhub1: at uhub0, port 12, addr 15 (disconnected)
> KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 14 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 14 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 18 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 18> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 16> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 16> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 16 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 16 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 17> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 17> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 18 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 17 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 17 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 21 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 21> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 19> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 19> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 19 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 19 (disconnected)
> ums0: detached
> ipmi0: KCS Error Data ff
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 20> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 20> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 21 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 20 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 20 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 24 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 24> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 22> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 22> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 22 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 22 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 23> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 23> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 24 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 23 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 23 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 27 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 27> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 25> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 25> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 25 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 25 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 26> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 26> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 27 (disconnected)
> ipmi0: KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 26 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 26 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 30 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 30> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 28> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 28> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 28 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 28 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 29> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 29> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> ipmi0: uhub1: at uhub0, port 12, addr 30 (disconnected)
> KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 29 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 29 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 33 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 33> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 31> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 31> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 31 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 31 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 32> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 32> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 33 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 32 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 32 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 36 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 36> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 34> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 34> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 34 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 34 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 35> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 35> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 36 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 35 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 35 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 39 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 39> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 37> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 37> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 37 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 37 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 38> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 38> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 39 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 38 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 38 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 42 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 42> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 40> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 40> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 40 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 40 (disconnected)
> ums0: detached
> ipmi0: KCS Error Data ff
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 41> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 41> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 42 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 41 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 41 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 45 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 45> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 43> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 43> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 43 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 43 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 44> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 44> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 45 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 44 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 44 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 48 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 48> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 46> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 46> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 46 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 46 (disconnected)
> ipmi0: KCS Error Data ff
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 47> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 47> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 48 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 47 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 47 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 51 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 51> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 49> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 49> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 49 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 49 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 50> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 50> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS Error Data ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> ipmi0: uhub1: at uhub0, port 12, addr 51 (disconnected)
> KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 50 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 50 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 54 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 54> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 52> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 52> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 52 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 52 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 53> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 53> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 54 (disconnected)
> ipmi0: KCS: Reply address mismatch
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 53 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 53 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS Error Data ff
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 57 failed, USB_ERR_SHORT_XFER
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 57> on usbus0
> uhub1: 4 ports with 3 removable, self powered
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 55> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 55> on usbus0
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ipmi0: KCS: Error retry exhausted
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 55 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 55 (disconnected)
> ums0: detached
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0
> ukbd0 on uhub1
> ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 56> on usbus0
> kbd0 at ukbd0
> ums0 on uhub1
> ums0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 56> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ipmi0: KCS: Failed to start write
> ipmi0: KCS error: ff
> ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 (disconnected)
> uhub1: at uhub0, port 12, addr 57 (disconnected)
> ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 (disconnected)
> ukbd0: at uhub1, port 1, addr 56 (disconnected)
> ukbd0: detached
> ums0: at uhub1, port 1, addr 56 (disconnected)
> ums0: detached
> uhub1: detached
> ipmi0: KCS: Failed to start write
> ipmi0: KCS Error Data ff
> usbd_setup_device_desc: getting device descriptor at addr 60 failed, USB_ERR_SHORT_XFER

[Message clipped]  

I think I am going to necro this one, because iwhat happened now seems to be very similar.
 
Status
Not open for further replies.

Similar threads

C
IPMI Related kernel log error messages - Is this a sensible course of action?
Replies
13
Views
2K
thepixelgeek
thepixelgeek
PenalunWil
  • Locked
understanding security run output.
Replies
11
Views
3K
Bidule0hm
Bidule0hm
C
  • Locked
Weird security output- Want help understanding what it is
Replies
13
Views
3K
Ceetan
C
glauco
SOLVED "KCS: Failed to start write" and other errors
Replies
4
Views
3K
nikkon
nikkon
N
  • Locked
Security Run Output, Any Issues?
Replies
4
Views
1K
NightNetworks
N
Top