Is this Error processing log message any real concern?

[Amsoil_Jim]

I have noticed this during startup and was wondering if was of any concern or not.
Currently running on FreeNAS 11.2RC, full system specs in signature

Code:

Nov  2 11:04:28 FreeNAS syslog-ng[2498]: Error processing log message: <ATA WDC WD30EFRX-68E 0A82> Fixed Direct Access SPC-4 SCSI device
da5: Serial Number WD-WCC4N1EX2CDZ
da5: 600.000MB/s transfers
da0: Command Queueing enabled
da4: 600.000MB/s transfersda3: quirks=0x8<4K>

da5: Command Queueing enabled
da2: quirks=0x8<4K>

da4: Command Queueing enabled
da4: 2861588MB (5860533168 512 byte sectors)
da4: quirks=0x8<4K>
da0: 2861588MB (5860533168 512 byte sectors)
da5: 2861588MB (5860533168 512 byte sectors)
da5: quirks=0x8<4K>
da0: quirks=0x8<4K>
da1 at mps0 bus 0 scbus7 target 11 lun 0
da1: <ATA WDC WD30EFRX-68E 0A82> Fixed Direct Access SPC-4 SCSI device
da1: Serial Number WD-WCC4N1EX2XER
da1: 600.000MB/s transfers
da1: Command Queueing enabled
da1: 2861588MB (5860533168 512 byte sectors)
da1: quirks=0x8<4K>
ses0: da1,pass4: Element descriptor: 'Slot 02'
ses0: da1,pass4: SAS Device Slot Element: 1 Phys at Slot 1
ses0:  phy 0: SATA device
ses0:  phy 0: parent 500304800028ad3f addr 500304800028ad0d
ses0: da2,pass5: Element descriptor: 'Slot 03'
ses0: da2,pass5: SAS Device Slot Element: 1 Phys at Slot 2
ses0:  phy 0: SATA device
ses0:  phy 0: parent 500304800028ad3f addr 500304800028ad0e
ses0: da3,pass6: Element descriptor: 'Slot 04'
ses0: da3,pass6: SAS Device Slot Element: 1 Phys at Slot 3
ses0:  phy 0: SATA device
ses0:  phy 0: parent 500304800028ad3f addr 500304800028ad0f
ses0: da4,pass7: Element descriptor: 'Slot 05'
ses0: da4,pass7: SAS Device Slot Element: 1 Phys at Slot 4
ses0:  phy 0: SATA device
ses0:  phy 0: parent 500304800028ad3f addr 500304800028ad10
ses0: da5,pass8: Element descriptor: 'Slot 06'
ses0: da5,pass8: SAS Device Slot Element: 1 Phys at Slot 5
ses0:  phy 0: SATA device
ses0:  phy 0: parent 500304800028ad3f addr 500304800028ad11
Trying to mount root from zfs:freenas-boot/ROOT/default []...
<5>igb0: link state changed to UP
<118>Loading early kernel modules:
<118>Syncing disks...
<118>
118>^[[2K^[[A^[[2KTotal Progress: [________________________________________] 0.00%^[[2K^[[A^[[2KTotal Progress: [########################################

 

[dlavigne]

Did you find the answer to your question?

 

[Amsoil_Jim]

No, but it has not caused any issues.