I have 4 x WD Red 8 TB SATA III harddisks.
They are connected through a HBA330 controller.
I installed FreeNAS 11.3 on two usb thumbdrives (da5 and da6)
After starting FreeNAS, the 4 harddisks do not show up in Storage->Disks (only da5 and da6, the two system thumbdrives, are listed).
If I list all the harddisks through the shell however using
egrep 'da[0-9]|cd[0-9]' /var/run/dmesg.boot
I do see the four disks.
Even though they are SATA disks, they are listed as /dev/da0 - da3 (rather than ada0 - ada3) so I guess this has to do with them attached through the HBA330 controller.
Why am I not seeing the disks in the list?
Could this be related to this reported FreeBSD 11.3 bug?
They are connected through a HBA330 controller.
I installed FreeNAS 11.3 on two usb thumbdrives (da5 and da6)
After starting FreeNAS, the 4 harddisks do not show up in Storage->Disks (only da5 and da6, the two system thumbdrives, are listed).
If I list all the harddisks through the shell however using
egrep 'da[0-9]|cd[0-9]' /var/run/dmesg.boot
I do see the four disks.
Code:
root@freenas[~]# egrep 'da[0-9]|cd[0-9]' /var/run/dmesg.boot cd1 at umass-sim0 bus 0 scbus9 target 0 lun 0 cd1: <iDRAC Virtual CD 0329> Removable CD-ROM SCSI device cd1: 40.000MB/s transfers cd1: Attempt to query device size failed: NOT READY, Medium not present cd1: quirks=0x10<10_BYTE_ONLY> cd0 at ahcich4 bus 0 scbus5 target 0 lun 0 cd0: <PLDS DVD+-RW DU-8A5LH 6D5M> Removable CD-ROM SCSI device cd0: Serial Number 2WXYCPLC008CO5417A01 cd0: 150.000MB/s transfers (SATA 1.x, UDMA6, ATAPI 12bytes, PIO 8192bytes) cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed ses0: cd0,pass4 in 'Slot 04', SATA Slot: scbus5 target 0 da6 at umass-sim2 bus 2 scbus11 target 0 lun 0 da6: <Samsung Flash Drive 1100> Removable Direct Access SPC-4 SCSI device da6: Serial Number 0376618060005180 da6: 40.000MB/s transfers da6: 30594MB (62656641 512 byte sectors) da6: quirks=0x2<NO_6_BYTE> da0 at mpr0 bus 0 scbus0 target 0 lun 0 da0: <ATA WDC WD80EFAX-68K 0A81> Fixed Direct Access SPC-4 SCSI device da0: Serial Number VDGKH7BD da0: 600.000MB/s transfers da0: Command Queueing enabled da0: 7630885MB (15628053168 512 byte sectors) da5 at umass-sim1 bus 1 scbus10 target 0 lun 0 da5: <SanDisk Ultra Fit 1.00> Removable Direct Access SPC-4 SCSI device da5: Serial Number 0501a75d3a785483e95494ba6b4ab5c97f28fe4ad6bfa7ede1a1caebfc8d da5: 40.000MB/s transfers da5: 29340MB (60088320 512 byte sectors) da5: quirks=0x2<NO_6_BYTE> da1 at mpr0 bus 0 scbus0 target 1 lun 0 da1: <ATA WDC WD80EFAX-68K 0A81> Fixed Direct Access SPC-4 SCSI device da1: Serial Number VDGKK77D da1: 600.000MB/s transfers da1: Command Queueing enabled da1: 7630885MB (15628053168 512 byte sectors) da2 at mpr0 bus 0 scbus0 target 2 lun 0 da2: <ATA WDC WD80EFAX-68K 0A81> Fixed Direct Access SPC-4 SCSI device da2: Serial Number VDGKDS2D da2: 600.000MB/s transfers da2: Command Queueing enabled da2: 7630885MB (15628053168 512 byte sectors) da3 at mpr0 bus 0 scbus0 target 3 lun 0 da3: <ATA WDC WD80EFAX-68K 0A81> Fixed Direct Access SPC-4 SCSI device da3: Serial Number VAK5SD7L da3: 600.000MB/s transfers da3: Command Queueing enabled da3: 7630885MB (15628053168 512 byte sectors) da4 at umass-sim0 bus 0 scbus9 target 0 lun 1 da4: <iDRAC Virtual Floppy 0329> Removable Direct Access SCSI device da4: 40.000MB/s transfers da4: Attempt to query device size failed: NOT READY, Medium not present da4: quirks=0x2<NO_6_BYTE> da4: Write Protected
Even though they are SATA disks, they are listed as /dev/da0 - da3 (rather than ada0 - ada3) so I guess this has to do with them attached through the HBA330 controller.
Why am I not seeing the disks in the list?
Could this be related to this reported FreeBSD 11.3 bug?