x11ssm-f

  1. O

    SUPERMICRO X11SSM-F compatibility

    Hello, i will chang my Freenas hardware t0 -SUPERMICRO X11SSM-F -Samsung - DDR4 - modul - 16 GB - DIMM 288-pin - 2666 MHz / PC4-21300 - CL19 - I cannot find inte i3 gen 6 or Gen 7 in the market , can i use the Gen 9 or G10 ? Is this Intel Core i3 9100F - 3.6 GHz working with...
  2. xaintly

    Build Report: Node 804, X11SSM, Xeon, PLEX

    Spoilers: Yes it will FreeNAS. I did some analysis planning what I wanted to build, and these forums were very helpful. There were some things I wish I'd known in advance, so hopefully this will help the next person. All of these parts are well-known and have been previously discussed as...
  3. A

    SOLVED Upgrade to 8x HDDs with controller

    Hey guys, my 4x 4TB WD Red in Raidz2 getting full and I'm planning upgrading my system soon. So the first problem I have is, that I want to add 4x 4TB WD Red to my current setup and theirfore I don't have enough slots. My motherboard is X11SSM-F from SuperMicro. Can somebody make some not...
  4. reub

    First Build: X11SSM-F Will it FreeNAS and Boot Device Question

    Hi all, Context Planning my first FreeNAS build based on the Supermicro X11SSM-F board. Would appreciate any feedback on the below config. I think it's fairly close to a lot of recommended builds on this board recently. This will be primarily file storage (backups and Plex data). Plan is for...
  5. P

    SuperMicro X11SSM-F + Kaby Lake G4600 = reboot loop on booting Linux/FreeNAS

    Hello, I'm trying to set up a new system but I'm having a bit of an issue booting FreeNAS (or any linux really..). Hardware: - SuperMicro X11SSM-F - Intel Pentium G4600 - 16 GB Samsung M391A2K43BB1 (DDR4 / ECC) The problem: After a successful POST, as soon as kernel begins to output text...
  6. Svengal

    Please, save me from myself.

    I’ve been putting together a parts list for my FreeNAS build and a few components have had me chasing my tail. Hopefully this isn’t too long a post. I’ve summarized the inline questions at the end on the remote chance someone wants to cut to the chase. Intended use Home and small office use...
  7. glauco

    Please assess this build (SuperMicro X11SSM-F + Intel Pentium G4560)

    Hello there, this is my first post. Can you please tell me what you think of this config I've been planning for the past few weeks? Motherboard: Supermicro MBD-X11SSM-F Micro-ATX LGA1151 ECC=yes Chipset=C236 8 SATA3 ports CPU: Intel Pentium G4560 (Kaby Lake) 3.5GHz Dual-Core Processor ECC=yes...
  8. S

    BUILD MB Supermicro X11SSM-F which RAM to use

    Hello, I need some helping hand on deciding which RAM to grab for my system. As MB I have decided that https://www.supermicro.com/products/motherboard/Xeon/C236_C232/X11SSM-F.cfm suits my needs with an I3-6300. On the RAM side I do not have the knowhow to understand which ram is needed for...
  9. J

    Problems upon first boot with Supermicro X11SSM-F

    I've just performed the first boot on a system with a Supermicro X11SSM-F board and a Pentium G4560 CPU. I ran into a few problems, however: I connected an old VGA monitor to see the POST output, but it stops at "PEI - CPU Initialization", with error 35. I googled the problem, and it seems...
  10. J

    Which fan connector is the CPU's on a X11SSM-F?

    Sorry if the answer to this question is obvious to you guys, but it's not to me. On page 11 of the Supermicro X11SSM-F manual they show the locations of five fan connectors, labeled FAN1, FAN2, FAN3, FAN4, and FANA. Later the same manual refers to the CPU fan connector, but doesn't specify (or...
  11. R

    Opinion needed for a new NAS system - Supermicro X11SSM-F or X11SSH-F or X11SSH-LN4F

    I am planing to setup a new FreeNAS system with the following setup: CPU: Pentium G4500 (i already have that CPU and i want to reuse it for the NAS) RAM: Kingston ValueRAM Intel DIMM Kit 32GB, DDR4-2133, CL15-15-15, ECC (KVR21E15D8K2/32I) (Crucial isn't available here at the moment) HDs for...
Top