sunshine931
Explorer
- Joined
- Jan 23, 2018
- Messages
- 54
I'm building a lab with an IBM x3650 M4. It's got an IBM M5110 RAID card (used only for boot), and an Intel RSP3GD016J (a rebranded LSI 9400-16e HBA). It's in IT mode, and has been flashed with the latest 24.00.01.01 Intel-provided firmware. I have two IBM SAS disk expansion trays attached to the 9400-16e, populated with 24x 8TB NLSAS drives.
TrueNAS Scale 22.12.3.
I can access the drives just fine (and am in the middle of removing Type 2 protection from them), but I can't seem to use sas3ircu. Should I be exclusively using storcli for the 9400-16e?
With sas3ircu I get:
dmesg output:
TrueNAS Scale 22.12.3.
I can access the drives just fine (and am in the middle of removing Type 2 protection from them), but I can't seem to use sas3ircu. Should I be exclusively using storcli for the 9400-16e?
With sas3ircu I get:
Code:
root@truenas[~/util]# sas3ircu list Avago Technologies SAS3 IR Configuration Utility. Version 16.00.00.00 (2017.04.26) Copyright (c) 2009-2017 Avago Technologies. All rights reserved. SAS3IRCU: MPTLib2 Error 1 root@truenas[~/util]# sas3ircu 0 display Avago Technologies SAS3 IR Configuration Utility. Version 16.00.00.00 (2017.04.26) Copyright (c) 2009-2017 Avago Technologies. All rights reserved. SAS3IRCU: No Controller Found at index 0. root@truenas[~/util]# sas3ircu 1 display Avago Technologies SAS3 IR Configuration Utility. Version 16.00.00.00 (2017.04.26) Copyright (c) 2009-2017 Avago Technologies. All rights reserved. SAS3IRCU: No Controller Found at index 1. root@truenas[~/util]#
dmesg output:
Code:
root@truenas[~/util]# dmesg| grep sas [ 6.542193] megasas: 07.717.02.00-rc1 [ 6.549234] megaraid_sas 0000:1b:00.0: BAR:0x1 BAR's base_addr(phys):0x00000000bc4bc000 mapped virt_addr:0x000000000ae3a0ce [ 6.549243] megaraid_sas 0000:1b:00.0: FW now in Ready state [ 6.555491] megaraid_sas 0000:1b:00.0: 63 bit DMA mask and 32 bit consistent mask [ 6.602398] mpt3sas version 39.100.00.00 loaded [ 6.724079] mpt3sas_cm0: 63 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (329990536 kB) [ 6.859014] megaraid_sas 0000:1b:00.0: firmware supports msix : (16) [ 6.873333] megaraid_sas 0000:1b:00.0: requested/available msix 16/16 poll_queue 0 [ 6.880522] megaraid_sas 0000:1b:00.0: current msix/online cpus : (16/32) [ 6.887671] megaraid_sas 0000:1b:00.0: RDPQ mode : (disabled) [ 6.894745] megaraid_sas 0000:1b:00.0: Current firmware supports maximum commands: 1008 LDIO threshold: 0 [ 7.690339] mpt3sas_cm0: MSI-X vectors supported: 128 [ 7.703815] mpt3sas_cm0: 0 32 32 [ 7.718695] mpt3sas_cm0: High IOPs queues : disabled [ 7.727773] mpt3sas0-msix0: PCI-MSI-X enabled: IRQ 93 [ 7.734238] mpt3sas0-msix1: PCI-MSI-X enabled: IRQ 94 [ 7.740639] mpt3sas0-msix2: PCI-MSI-X enabled: IRQ 95 [ 7.746919] mpt3sas0-msix3: PCI-MSI-X enabled: IRQ 96 [ 7.753117] mpt3sas0-msix4: PCI-MSI-X enabled: IRQ 97 [ 7.759224] mpt3sas0-msix5: PCI-MSI-X enabled: IRQ 98 [ 7.765271] mpt3sas0-msix6: PCI-MSI-X enabled: IRQ 99 [ 7.771166] mpt3sas0-msix7: PCI-MSI-X enabled: IRQ 100 [ 7.776882] mpt3sas0-msix8: PCI-MSI-X enabled: IRQ 101 [ 7.782445] mpt3sas0-msix9: PCI-MSI-X enabled: IRQ 102 [ 7.787867] mpt3sas0-msix10: PCI-MSI-X enabled: IRQ 103 [ 7.793269] mpt3sas0-msix11: PCI-MSI-X enabled: IRQ 104 [ 7.798545] mpt3sas0-msix12: PCI-MSI-X enabled: IRQ 105 [ 7.803672] mpt3sas0-msix13: PCI-MSI-X enabled: IRQ 106 [ 7.808643] mpt3sas0-msix14: PCI-MSI-X enabled: IRQ 107 [ 7.813511] mpt3sas0-msix15: PCI-MSI-X enabled: IRQ 108 [ 7.818254] mpt3sas0-msix16: PCI-MSI-X enabled: IRQ 109 [ 7.822889] mpt3sas0-msix17: PCI-MSI-X enabled: IRQ 110 [ 7.827414] mpt3sas0-msix18: PCI-MSI-X enabled: IRQ 111 [ 7.831776] mpt3sas0-msix19: PCI-MSI-X enabled: IRQ 112 [ 7.836094] mpt3sas0-msix20: PCI-MSI-X enabled: IRQ 113 [ 7.840334] mpt3sas0-msix21: PCI-MSI-X enabled: IRQ 114 [ 7.844440] mpt3sas0-msix22: PCI-MSI-X enabled: IRQ 115 [ 7.848414] mpt3sas0-msix23: PCI-MSI-X enabled: IRQ 116 [ 7.852382] mpt3sas0-msix24: PCI-MSI-X enabled: IRQ 117 [ 7.856226] mpt3sas0-msix25: PCI-MSI-X enabled: IRQ 118 [ 7.859985] mpt3sas0-msix26: PCI-MSI-X enabled: IRQ 119 [ 7.863615] mpt3sas0-msix27: PCI-MSI-X enabled: IRQ 120 [ 7.867132] mpt3sas0-msix28: PCI-MSI-X enabled: IRQ 121 [ 7.870519] mpt3sas0-msix29: PCI-MSI-X enabled: IRQ 122 [ 7.873787] mpt3sas0-msix30: PCI-MSI-X enabled: IRQ 123 [ 7.876895] mpt3sas0-msix31: PCI-MSI-X enabled: IRQ 124 [ 7.879861] mpt3sas_cm0: iomem(0x00000000be200000), mapped(0x00000000110a6533), size(1048576) [ 7.883127] mpt3sas_cm0: ioport(0x0000000000002f00), size(256) [ 8.079851] megaraid_sas 0000:1b:00.0: Performance mode :Latency (latency index = 1) [ 8.083914] megaraid_sas 0000:1b:00.0: FW supports sync cache : No [ 8.088048] megaraid_sas 0000:1b:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009 [ 8.693102] megaraid_sas 0000:1b:00.0: FW provided supportMaxExtLDs: 1 max_lds: 64 [ 8.698294] megaraid_sas 0000:1b:00.0: controller type : MR(1024MB) [ 8.703549] megaraid_sas 0000:1b:00.0: Online Controller Reset(OCR) : Enabled [ 8.708832] megaraid_sas 0000:1b:00.0: Secure JBOD support : No [ 8.714204] megaraid_sas 0000:1b:00.0: NVMe passthru support : No [ 8.719631] megaraid_sas 0000:1b:00.0: FW provided TM TaskAbort/Reset timeout : 0 secs/0 secs [ 8.725260] megaraid_sas 0000:1b:00.0: JBOD sequence map support : No [ 8.730966] megaraid_sas 0000:1b:00.0: PCI Lane Margining support : No [ 9.732478] megaraid_sas 0000:1b:00.0: megasas_enable_intr_fusion is called outbound_intr_mask:0x40000000 [ 9.739964] megaraid_sas 0000:1b:00.0: INIT adapter done [ 9.747501] megaraid_sas 0000:1b:00.0: JBOD sequence map is disabled megasas_setup_jbod_map 5804 [ 9.763736] megaraid_sas 0000:1b:00.0: pci id : (0x1000)/(0x005b)/(0x1014)/(0x040b) [ 9.779569] megaraid_sas 0000:1b:00.0: unevenspan support : no [ 9.787503] megaraid_sas 0000:1b:00.0: firmware crash dump : no [ 9.795360] megaraid_sas 0000:1b:00.0: JBOD sequence map : disabled [ 9.811175] megaraid_sas 0000:1b:00.0: Max firmware commands: 1007 shared with default hw_queues = 15 poll_queues 0 [ 9.838809] mpt3sas_cm0: sending message unit reset !! [ 9.848315] mpt3sas_cm0: message unit reset: SUCCESS [ 9.882433] mpt3sas_cm0: scatter gather: sge_in_main_msg(1), sge_per_chain(7), sge_per_io(128), chains_per_io(19) [ 9.899017] mpt3sas_cm0: request pool(0x00000000cb66956b) - dma(0x102100000): depth(6756), frame_size(128), pool_size(844 kB) [ 10.083137] mpt3sas_cm0: sense pool(0x00000000c9602676) - dma(0x102600000): depth(6551), element_size(96), pool_size (614 kB) [ 10.092196] mpt3sas_cm0: reply pool(0x000000007748d33c) - dma(0x102700000): depth(6820), frame_size(128), pool_size(852 kB) [ 10.101005] mpt3sas_cm0: config page(0x00000000b8abcbc2) - dma(0x12393d000): size(512) [ 10.109580] mpt3sas_cm0: Allocated physical memory: size(31938 kB) [ 10.118059] mpt3sas_cm0: Current Controller Queue Depth(6548),Max Controller Queue Depth(6656) [ 10.126680] mpt3sas_cm0: Scatter Gather Elements per IO(128) [ 10.179459] mpt3sas_cm0: _base_display_fwpkg_version: complete [ 10.188071] mpt3sas_cm0: FW Package Ver(24.00.01.01) [ 10.196902] mpt3sas_cm0: TimeSync Interval in Manuf page-11 is not enabled. Periodic Time-Sync will be disabled [ 10.206044] mpt3sas_cm0: SAS3416: FWVersion(24.00.01.00), ChipRevision(0x01), BiosVersion(00.00.00.00) [ 10.214935] mpt3sas_cm0: Intel(R) Controller: Subsystem ID: 0x3020 [ 10.223858] mpt3sas_cm0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Diag Trace Buffer,Task Set Full,NCQ) [ 10.241910] mpt3sas 0000:0c:00.0: Max SCSIIO MPT commands: 6548 shared with nr_hw_queues = 32 [ 10.327046] mpt3sas_cm0: sending port enable !! [ 10.336753] mpt3sas_cm0: hba_port entry: 0000000061776388, port: 0 is added to hba_port list [ 10.347289] mpt3sas_cm0: hba_port entry: 000000001c2d8f01, port: 8 is added to hba_port list [ 10.366706] mpt3sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b00dd93380), phys(21) [ 10.377658] mpt3sas_cm0: expander_add: handle(0x0033), parent(0x0001), sas_addr(0x500507681105b4bf), phys(37) [ 10.387759] expander-1:0: add: handle(0x0033), sas_addr(0x500507681105b4bf) [ 10.402591] mpt3sas_cm0: handle(0x34) sas_address(0x5000c500a6cc1de9) port_type(0x1) [ 10.428023] scsi 1:0:0:0: SSP: handle(0x0034), sas_addr(0x5000c500a6cc1de9), phy(0), device_name(0x5000c500a6cc1de8) [ 10.450956] end_device-1:0:0: add: handle(0x0034), sas_addr(0x5000c500a6cc1de9) [ 10.461018] mpt3sas_cm0: handle(0x35) sas_address(0x5000c500a6cc2c41) port_type(0x1) [ 10.516021] scsi 1:0:1:0: SSP: handle(0x0035), sas_addr(0x5000c500a6cc2c41), phy(1), device_name(0x5000c500a6cc2c40) [ 10.568872] end_device-1:0:1: add: handle(0x0035), sas_addr(0x5000c500a6cc2c41) [ 10.586704] mpt3sas_cm0: handle(0x36) sas_address(0x5000c500a6cd4209) port_type(0x1) [ 10.612444] scsi 1:0:2:0: SSP: handle(0x0036), sas_addr(0x5000c500a6cd4209), phy(2), device_name(0x5000c500a6cd4208) [ 10.635761] end_device-1:0:2: add: handle(0x0036), sas_addr(0x5000c500a6cd4209) [ 10.645968] mpt3sas_cm0: handle(0x37) sas_address(0x5000c500a6ef2df9) port_type(0x1) [ 10.674561] scsi 1:0:3:0: SSP: handle(0x0037), sas_addr(0x5000c500a6ef2df9), phy(3), device_name(0x5000c500a6ef2df8) [ 10.698480] end_device-1:0:3: add: handle(0x0037), sas_addr(0x5000c500a6ef2df9) [ 10.708929] mpt3sas_cm0: handle(0x38) sas_address(0x5000c500a6ef34f5) port_type(0x1) [ 10.738435] scsi 1:0:4:0: SSP: handle(0x0038), sas_addr(0x5000c500a6ef34f5), phy(4), device_name(0x5000c500a6ef34f4) [ 10.762541] end_device-1:0:4: add: handle(0x0038), sas_addr(0x5000c500a6ef34f5) [ 10.773166] mpt3sas_cm0: handle(0x39) sas_address(0x5000c500a6eed8f5) port_type(0x1) [ 10.805228] scsi 1:0:5:0: SSP: handle(0x0039), sas_addr(0x5000c500a6eed8f5), phy(5), device_name(0x5000c500a6eed8f4) [ 10.829794] end_device-1:0:5: add: handle(0x0039), sas_addr(0x5000c500a6eed8f5) [ 10.840618] mpt3sas_cm0: handle(0x3a) sas_address(0x5000c500a6cd0c39) port_type(0x1) [ 10.874171] scsi 1:0:6:0: SSP: handle(0x003a), sas_addr(0x5000c500a6cd0c39), phy(6), device_name(0x5000c500a6cd0c38) [ 10.898895] end_device-1:0:6: add: handle(0x003a), sas_addr(0x5000c500a6cd0c39) [ 10.909786] mpt3sas_cm0: handle(0x3b) sas_address(0x5000c500a6ef28b1) port_type(0x1) [ 10.942802] scsi 1:0:7:0: SSP: handle(0x003b), sas_addr(0x5000c500a6ef28b1), phy(7), device_name(0x5000c500a6ef28b0) [ 10.978521] end_device-1:0:7: add: handle(0x003b), sas_addr(0x5000c500a6ef28b1) [ 10.989747] mpt3sas_cm0: handle(0x3c) sas_address(0x5000c500a6fb7285) port_type(0x1) [ 11.012840] scsi 1:0:8:0: SSP: handle(0x003c), sas_addr(0x5000c500a6fb7285), phy(8), device_name(0x5000c500a6fb7284) [ 11.037606] end_device-1:0:8: add: handle(0x003c), sas_addr(0x5000c500a6fb7285) [ 11.048755] mpt3sas_cm0: handle(0x3d) sas_address(0x5000c500a6cd4751) port_type(0x1) [ 11.083032] scsi 1:0:9:0: SSP: handle(0x003d), sas_addr(0x5000c500a6cd4751), phy(9), device_name(0x5000c500a6cd4750) [ 11.108291] end_device-1:0:9: add: handle(0x003d), sas_addr(0x5000c500a6cd4751) [ 11.119510] mpt3sas_cm0: handle(0x3e) sas_address(0x5000c500a6ccde59) port_type(0x1) [ 11.158114] scsi 1:0:10:0: SSP: handle(0x003e), sas_addr(0x5000c500a6ccde59), phy(10), device_name(0x5000c500a6ccde58) [ 11.227768] end_device-1:0:10: add: handle(0x003e), sas_addr(0x5000c500a6ccde59) [ 11.238934] mpt3sas_cm0: handle(0x3f) sas_address(0x5000c500a6cc3351) port_type(0x1) [ 11.274511] scsi 1:0:11:0: SSP: handle(0x003f), sas_addr(0x5000c500a6cc3351), phy(11), device_name(0x5000c500a6cc3350) [ 11.299726] end_device-1:0:11: add: handle(0x003f), sas_addr(0x5000c500a6cc3351) [ 11.311683] mpt3sas_cm0: handle(0x41) sas_address(0x500507681105b4be) port_type(0x1) [ 11.346209] scsi 1:0:12:0: SES: handle(0x0041), sas_addr(0x500507681105b4be), phy(36), device_name(0x0000000000000000) [ 11.391798] end_device-1:0:12: add: handle(0x0041), sas_addr(0x500507681105b4be) [ 11.402995] mpt3sas_cm0: expander_add: handle(0x0040), parent(0x0033), sas_addr(0x500507681105c1bf), phys(37) [ 11.414200] expander-1:1: add: handle(0x0040), sas_addr(0x500507681105c1bf) [ 11.429322] mpt3sas_cm0: handle(0x42) sas_address(0x5000c500a6cd4fa9) port_type(0x1) [ 11.460656] scsi 1:0:13:0: SSP: handle(0x0042), sas_addr(0x5000c500a6cd4fa9), phy(0), device_name(0x5000c500a6cd4fa8) [ 11.485676] end_device-1:1:0: add: handle(0x0042), sas_addr(0x5000c500a6cd4fa9) [ 11.496859] mpt3sas_cm0: handle(0x43) sas_address(0x5000c500a6cc63a9) port_type(0x1) [ 11.528535] scsi 1:0:14:0: SSP: handle(0x0043), sas_addr(0x5000c500a6cc63a9), phy(1), device_name(0x5000c500a6cc63a8) [ 11.564433] end_device-1:1:1: add: handle(0x0043), sas_addr(0x5000c500a6cc63a9) [ 11.575385] mpt3sas_cm0: handle(0x44) sas_address(0x5000c500a6cc4825) port_type(0x1) [ 11.606689] scsi 1:0:15:0: SSP: handle(0x0044), sas_addr(0x5000c500a6cc4825), phy(2), device_name(0x5000c500a6cc4824) [ 11.631566] end_device-1:1:2: add: handle(0x0044), sas_addr(0x5000c500a6cc4825) [ 11.642477] mpt3sas_cm0: handle(0x45) sas_address(0x5000c500a6ccd8e5) port_type(0x1) [ 11.670308] scsi 1:0:16:0: SSP: handle(0x0045), sas_addr(0x5000c500a6ccd8e5), phy(3), device_name(0x5000c500a6ccd8e4) [ 11.695113] end_device-1:1:3: add: handle(0x0045), sas_addr(0x5000c500a6ccd8e5) [ 11.706021] mpt3sas_cm0: handle(0x46) sas_address(0x5000c500a6cc35a1) port_type(0x1) [ 11.739952] scsi 1:0:17:0: SSP: handle(0x0046), sas_addr(0x5000c500a6cc35a1), phy(4), device_name(0x5000c500a6cc35a0) [ 11.809095] end_device-1:1:4: add: handle(0x0046), sas_addr(0x5000c500a6cc35a1) [ 11.829110] mpt3sas_cm0: handle(0x47) sas_address(0x5000c500a6fbce99) port_type(0x1) [ 11.872317] scsi 1:0:18:0: SSP: handle(0x0047), sas_addr(0x5000c500a6fbce99), phy(5), device_name(0x5000c500a6fbce98) [ 11.897334] end_device-1:1:5: add: handle(0x0047), sas_addr(0x5000c500a6fbce99) [ 11.908311] mpt3sas_cm0: handle(0x48) sas_address(0x5000c500a6fbaa49) port_type(0x1) [ 11.942198] scsi 1:0:19:0: SSP: handle(0x0048), sas_addr(0x5000c500a6fbaa49), phy(6), device_name(0x5000c500a6fbaa48) [ 11.967264] end_device-1:1:6: add: handle(0x0048), sas_addr(0x5000c500a6fbaa49) [ 11.978420] mpt3sas_cm0: handle(0x49) sas_address(0x5000c500a6cd436d) port_type(0x1) [ 12.012677] scsi 1:0:20:0: SSP: handle(0x0049), sas_addr(0x5000c500a6cd436d), phy(7), device_name(0x5000c500a6cd436c) [ 12.037931] end_device-1:1:7: add: handle(0x0049), sas_addr(0x5000c500a6cd436d) [ 12.049038] mpt3sas_cm0: handle(0x4a) sas_address(0x5000c500a6fb9cfd) port_type(0x1) [ 12.082052] scsi 1:0:21:0: SSP: handle(0x004a), sas_addr(0x5000c500a6fb9cfd), phy(8), device_name(0x5000c500a6fb9cfc) [ 12.118324] end_device-1:1:8: add: handle(0x004a), sas_addr(0x5000c500a6fb9cfd) [ 12.129427] mpt3sas_cm0: handle(0x4b) sas_address(0x5000c500a6cc1d25) port_type(0x1) [ 12.160344] scsi 1:0:22:0: SSP: handle(0x004b), sas_addr(0x5000c500a6cc1d25), phy(9), device_name(0x5000c500a6cc1d24) [ 12.185640] end_device-1:1:9: add: handle(0x004b), sas_addr(0x5000c500a6cc1d25) [ 12.196826] mpt3sas_cm0: handle(0x4c) sas_address(0x5000c500a6ccf929) port_type(0x1) [ 12.225130] scsi 1:0:23:0: SSP: handle(0x004c), sas_addr(0x5000c500a6ccf929), phy(10), device_name(0x5000c500a6ccf928) [ 12.250430] end_device-1:1:10: add: handle(0x004c), sas_addr(0x5000c500a6ccf929) [ 12.261573] mpt3sas_cm0: handle(0x4d) sas_address(0x5000c500a6cd46e9) port_type(0x1) [ 12.296311] scsi 1:0:24:0: SSP: handle(0x004d), sas_addr(0x5000c500a6cd46e9), phy(11), device_name(0x5000c500a6cd46e8) [ 12.343572] end_device-1:1:11: add: handle(0x004d), sas_addr(0x5000c500a6cd46e9) [ 12.363000] mpt3sas_cm0: handle(0x4e) sas_address(0x500507681105c1be) port_type(0x1) [ 12.406980] scsi 1:0:25:0: SES: handle(0x004e), sas_addr(0x500507681105c1be), phy(36), device_name(0x0000000000000000) [ 12.453122] end_device-1:1:12: add: handle(0x004e), sas_addr(0x500507681105c1be) [ 12.464543] mpt3sas_cm0: expander_add: handle(0x0017), parent(0x0009), sas_addr(0x500507681105b4ff), phys(37) [ 12.475989] expander-1:2: add: handle(0x0017), sas_addr(0x500507681105b4ff) [ 12.491438] mpt3sas_cm0: handle(0x18) sas_address(0x5000c500a6cc1dea) port_type(0x1) [ 12.530164] scsi 1:0:26:0: SSP: handle(0x0018), sas_addr(0x5000c500a6cc1dea), phy(0), device_name(0x5000c500a6cc1de8) [ 12.555701] end_device-1:2:0: add: handle(0x0018), sas_addr(0x5000c500a6cc1dea) [ 12.566920] mpt3sas_cm0: handle(0x19) sas_address(0x5000c500a6cc2c42) port_type(0x1) [ 12.599876] scsi 1:0:27:0: SSP: handle(0x0019), sas_addr(0x5000c500a6cc2c42), phy(1), device_name(0x5000c500a6cc2c40) [ 12.625356] end_device-1:2:1: add: handle(0x0019), sas_addr(0x5000c500a6cc2c42) [ 12.636563] mpt3sas_cm0: handle(0x1a) sas_address(0x5000c500a6cd420a) port_type(0x1) [ 12.672283] scsi 1:0:28:0: SSP: handle(0x001a), sas_addr(0x5000c500a6cd420a), phy(2), device_name(0x5000c500a6cd4208) [ 12.708912] end_device-1:2:2: add: handle(0x001a), sas_addr(0x5000c500a6cd420a) [ 12.720147] mpt3sas_cm0: handle(0x1b) sas_address(0x5000c500a6ef2dfa) port_type(0x1) [ 12.757044] scsi 1:0:29:0: SSP: handle(0x001b), sas_addr(0x5000c500a6ef2dfa), phy(3), device_name(0x5000c500a6ef2df8) [ 12.782521] end_device-1:2:3: add: handle(0x001b), sas_addr(0x5000c500a6ef2dfa) [ 12.793795] mpt3sas_cm0: handle(0x1c) sas_address(0x5000c500a6ef34f6) port_type(0x1) [ 12.822449] scsi 1:0:30:0: SSP: handle(0x001c), sas_addr(0x5000c500a6ef34f6), phy(4), device_name(0x5000c500a6ef34f4) [ 12.848004] end_device-1:2:4: add: handle(0x001c), sas_addr(0x5000c500a6ef34f6) [ 12.859250] mpt3sas_cm0: handle(0x1d) sas_address(0x5000c500a6eed8f6) port_type(0x1) [ 12.947600] scsi 1:0:31:0: SSP: handle(0x001d), sas_addr(0x5000c500a6eed8f6), phy(5), device_name(0x5000c500a6eed8f4) [ 12.972367] end_device-1:2:5: add: handle(0x001d), sas_addr(0x5000c500a6eed8f6) [ 12.983284] mpt3sas_cm0: handle(0x1e) sas_address(0x5000c500a6cd0c3a) port_type(0x1) [ 13.021185] scsi 1:0:32:0: SSP: handle(0x001e), sas_addr(0x5000c500a6cd0c3a), phy(6), device_name(0x5000c500a6cd0c38) [ 13.046209] end_device-1:2:6: add: handle(0x001e), sas_addr(0x5000c500a6cd0c3a) [ 13.057187] mpt3sas_cm0: handle(0x1f) sas_address(0x5000c500a6ef28b2) port_type(0x1) [ 13.087062] scsi 1:0:33:0: SSP: handle(0x001f), sas_addr(0x5000c500a6ef28b2), phy(7), device_name(0x5000c500a6ef28b0) [ 13.112304] end_device-1:2:7: add: handle(0x001f), sas_addr(0x5000c500a6ef28b2) [ 13.123491] mpt3sas_cm0: handle(0x20) sas_address(0x5000c500a6fb7286) port_type(0x1) [ 13.159397] scsi 1:0:34:0: SSP: handle(0x0020), sas_addr(0x5000c500a6fb7286), phy(8), device_name(0x5000c500a6fb7284) [ 13.184482] end_device-1:2:8: add: handle(0x0020), sas_addr(0x5000c500a6fb7286) [ 13.195703] mpt3sas_cm0: handle(0x21) sas_address(0x5000c500a6cd4752) port_type(0x1) [ 13.231920] scsi 1:0:35:0: SSP: handle(0x0021), sas_addr(0x5000c500a6cd4752), phy(9), device_name(0x5000c500a6cd4750) [ 13.257013] end_device-1:2:9: add: handle(0x0021), sas_addr(0x5000c500a6cd4752) [ 13.268219] mpt3sas_cm0: handle(0x22) sas_address(0x5000c500a6ccde5a) port_type(0x1) [ 13.304730] scsi 1:0:36:0: SSP: handle(0x0022), sas_addr(0x5000c500a6ccde5a), phy(10), device_name(0x5000c500a6ccde58) [ 13.329879] end_device-1:2:10: add: handle(0x0022), sas_addr(0x5000c500a6ccde5a) [ 13.341019] mpt3sas_cm0: handle(0x23) sas_address(0x5000c500a6cc3352) port_type(0x1) [ 13.377545] scsi 1:0:37:0: SSP: handle(0x0023), sas_addr(0x5000c500a6cc3352), phy(11), device_name(0x5000c500a6cc3350) [ 13.402648] end_device-1:2:11: add: handle(0x0023), sas_addr(0x5000c500a6cc3352) [ 13.414546] mpt3sas_cm0: handle(0x25) sas_address(0x500507681105b4fe) port_type(0x1) [ 13.448855] scsi 1:0:38:0: SES: handle(0x0025), sas_addr(0x500507681105b4fe), phy(36), device_name(0x0000000000000000) [ 13.497919] end_device-1:2:12: add: handle(0x0025), sas_addr(0x500507681105b4fe) [ 13.509290] mpt3sas_cm0: expander_add: handle(0x0024), parent(0x0017), sas_addr(0x500507681105c1ff), phys(37) [ 13.520376] expander-1:3: add: handle(0x0024), sas_addr(0x500507681105c1ff) [ 13.535632] mpt3sas_cm0: handle(0x26) sas_address(0x5000c500a6cd4faa) port_type(0x1) [ 13.565803] scsi 1:0:39:0: SSP: handle(0x0026), sas_addr(0x5000c500a6cd4faa), phy(0), device_name(0x5000c500a6cd4fa8) [ 13.591256] end_device-1:3:0: add: handle(0x0026), sas_addr(0x5000c500a6cd4faa) [ 13.602599] mpt3sas_cm0: handle(0x27) sas_address(0x5000c500a6cc63aa) port_type(0x1) [ 13.631839] scsi 1:0:40:0: SSP: handle(0x0027), sas_addr(0x5000c500a6cc63aa), phy(1), device_name(0x5000c500a6cc63a8) [ 13.657394] end_device-1:3:1: add: handle(0x0027), sas_addr(0x5000c500a6cc63aa) [ 13.668783] mpt3sas_cm0: handle(0x28) sas_address(0x5000c500a6cc4826) port_type(0x1) [ 13.702987] scsi 1:0:41:0: SSP: handle(0x0028), sas_addr(0x5000c500a6cc4826), phy(2), device_name(0x5000c500a6cc4824) [ 13.728597] end_device-1:3:2: add: handle(0x0028), sas_addr(0x5000c500a6cc4826) [ 13.740010] mpt3sas_cm0: handle(0x29) sas_address(0x5000c500a6ccd8e6) port_type(0x1) [ 13.770118] scsi 1:0:42:0: SSP: handle(0x0029), sas_addr(0x5000c500a6ccd8e6), phy(3), device_name(0x5000c500a6ccd8e4) [ 13.795684] end_device-1:3:3: add: handle(0x0029), sas_addr(0x5000c500a6ccd8e6) [ 13.807019] mpt3sas_cm0: handle(0x2a) sas_address(0x5000c500a6cc35a2) port_type(0x1) [ 13.845297] scsi 1:0:43:0: SSP: handle(0x002a), sas_addr(0x5000c500a6cc35a2), phy(4), device_name(0x5000c500a6cc35a0) [ 13.870865] end_device-1:3:4: add: handle(0x002a), sas_addr(0x5000c500a6cc35a2) [ 13.882199] mpt3sas_cm0: handle(0x2b) sas_address(0x5000c500a6fbce9a) port_type(0x1) [ 13.915941] scsi 1:0:44:0: SSP: handle(0x002b), sas_addr(0x5000c500a6fbce9a), phy(5), device_name(0x5000c500a6fbce98) [ 13.941567] end_device-1:3:5: add: handle(0x002b), sas_addr(0x5000c500a6fbce9a) [ 13.952987] mpt3sas_cm0: handle(0x2c) sas_address(0x5000c500a6fbaa4a) port_type(0x1) [ 13.990714] scsi 1:0:45:0: SSP: handle(0x002c), sas_addr(0x5000c500a6fbaa4a), phy(6), device_name(0x5000c500a6fbaa48) [ 14.016296] end_device-1:3:6: add: handle(0x002c), sas_addr(0x5000c500a6fbaa4a) [ 14.027744] mpt3sas_cm0: handle(0x2d) sas_address(0x5000c500a6cd436e) port_type(0x1) [ 14.061943] scsi 1:0:46:0: SSP: handle(0x002d), sas_addr(0x5000c500a6cd436e), phy(7), device_name(0x5000c500a6cd436c) [ 14.087476] end_device-1:3:7: add: handle(0x002d), sas_addr(0x5000c500a6cd436e) [ 14.098965] mpt3sas_cm0: handle(0x2e) sas_address(0x5000c500a6fb9cfe) port_type(0x1) [ 14.136987] scsi 1:0:47:0: SSP: handle(0x002e), sas_addr(0x5000c500a6fb9cfe), phy(8), device_name(0x5000c500a6fb9cfc) [ 14.162814] end_device-1:3:8: add: handle(0x002e), sas_addr(0x5000c500a6fb9cfe) [ 14.174444] mpt3sas_cm0: handle(0x2f) sas_address(0x5000c500a6cc1d26) port_type(0x1) [ 14.211800] scsi 1:0:48:0: SSP: handle(0x002f), sas_addr(0x5000c500a6cc1d26), phy(9), device_name(0x5000c500a6cc1d24) [ 14.237617] end_device-1:3:9: add: handle(0x002f), sas_addr(0x5000c500a6cc1d26) [ 14.249119] mpt3sas_cm0: handle(0x30) sas_address(0x5000c500a6ccf92a) port_type(0x1) [ 14.286028] scsi 1:0:49:0: SSP: handle(0x0030), sas_addr(0x5000c500a6ccf92a), phy(10), device_name(0x5000c500a6ccf928) [ 14.311886] end_device-1:3:10: add: handle(0x0030), sas_addr(0x5000c500a6ccf92a) [ 14.323376] mpt3sas_cm0: handle(0x31) sas_address(0x5000c500a6cd46ea) port_type(0x1) [ 14.360726] scsi 1:0:50:0: SSP: handle(0x0031), sas_addr(0x5000c500a6cd46ea), phy(11), device_name(0x5000c500a6cd46e8) [ 14.386566] end_device-1:3:11: add: handle(0x0031), sas_addr(0x5000c500a6cd46ea) [ 14.398701] mpt3sas_cm0: handle(0x32) sas_address(0x500507681105c1fe) port_type(0x1) [ 14.433774] scsi 1:0:51:0: SES: handle(0x0032), sas_addr(0x500507681105c1fe), phy(36), device_name(0x0000000000000000) [ 14.480180] end_device-1:3:12: add: handle(0x0032), sas_addr(0x500507681105c1fe) [ 14.493309] mpt3sas_cm0: port enable: SUCCESS
Last edited: