Smartctl wrong/right? Second hand drive shows zero hours

[Keyakinan]

Hi!

I've just bought a second hand HDD (Seagate IronWolf Pro 14tb), should only be used for a month tops.

Right now I've done a conveyance scan, short and extended trough the GUI of TrueNAS, see results below.

I am running a long scan for about 6-7 hours now and the drive does not have any indication ( as far as I can see) that it is second hand.

Am I lucky? They guy acted wierd about it when I asked him if he resetted the SMART values.
So chances this is an HDD straight from factory (they come with blank SMART results if I'm right or something else going on?

Also if the test come back good, is it still wise to run badblocks after this?

Might be formated funky but Power_On_Hours says "6"

Show : smartctl -a /dev/ada1

smartctl -a /dev/ada1

smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p2 amd64] (local build)

Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org



=== START OF INFORMATION SECTION ===

Model Family: Seagate IronWolf Pro

Device Model: ST14000NE0008-2JK101

Serial Number: ZHZ2HSSZ

LU WWN Device Id: 5 000c50 0b5530972

Firmware Version: EN01

User Capacity: 14,000,519,643,136 bytes [14.0 TB]

Sector Sizes: 512 bytes logical, 4096 bytes physical

Rotation Rate: 7200 rpm

Form Factor: 3.5 inches

Device is: In smartctl database [for details use: -P show]

ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5

SATA Version is: SATA 3.3, 6.0 Gb/s (current: 3.0 Gb/s)

Local Time is: Tue Jan 26 22:30:56 2021 CET

SMART support is: Available - device has SMART capability.

SMART support is: Enabled



=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED



General SMART Values:

Offline data collection status: (0x82) Offline data collection activity

was completed without error.

Auto Offline Data Collection: Enabled.

Self-test execution status: ( 247) Self-test routine in progress...

70% of test remaining.

Total time to complete Offline

data collection: ( 567) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 1) minutes.

Extended self-test routine

recommended polling time: (1263) minutes.

Conveyance self-test routine

recommended polling time: ( 2) minutes.

SCT capabilities: (0x50bd) SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.



SMART Attributes Data Structure revision number: 10

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x000f 083 083 044 Pre-fail Always - 213316086

3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0

4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4

5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0

7 Seek_Error_Rate 0x000f 064 060 045 Pre-fail Always - 2408382

9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 6

10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0

12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4

18 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0

187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0

188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0

190 Airflow_Temperature_Cel 0x0022 066 065 040 Old_age Always - 34 (Min/Max 23/35)

192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 3

193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 10

194 Temperature_Celsius 0x0022 034 040 000 Old_age Always - 34 (0 15 0 0 0)

195 Hardware_ECC_Recovered 0x001a 083 083 000 Old_age Always - 213316086

197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0

198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0

199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0

200 Multi_Zone_Error_Rate 0x0023 100 100 001 Pre-fail Always - 0

240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6 (148 198 0)

241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 0

242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 213316086



SMART Error Log Version: 1

No Errors Logged



SMART Self-test log structure revision number 1

Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error

# 1 Extended offline Self-test routine in progress 70% 6 -

# 2 Short offline Completed without error 00% 1 -

# 3 Conveyance offline Completed without error 00% 0 -



SMART Selective self-test log data structure revision number 1

SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS

1 0 0 Not_testing

2 0 0 Not_testing

3 0 0 Not_testing

4 0 0 Not_testing

5 0 0 Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

[sretalla]

I have seen mention of a process that could be used on some (older, as it's apparently now secured on more recent models) Seagate drives that a connection with RS.232 to the drive can be used to reset the values.

Very hard to say how you would know if that had been done or not though.

 

[Etorix]

Badblocks after full SMART tests is the recommended burn-in process.
The seller reacting weirdly might be an indication that he somehow wiped the SMART data and did not expect to be caught. But you can't complain about getting a second-hand drive when you bought just that. If the tests show no error, all should be fine.

 

[Keyakinan]

Badblocks after full SMART tests is the recommended burn-in process.
The seller reacting weirdly might be an indication that he somehow wiped the SMART data and did not expect to be caught. But you can't complain about getting a second-hand drive when you bought just that. If the tests show no error, all should be fine.

Thanks for your reaction, I will run badblocks!
I'm not complaining about a second-hand drive. But he says its a month old and if it is 3 years old with 26k hours then I'm complaining ;)

 

[Alecmascot]

I'm not complaining about a second-hand drive. But he says its a month old and if it is 3 years old with 26k hours then I'm complaining ;)

Run the serial number through Seagate's warranty system.

 

[pschatz100]

According to suggested drive burn-in comments, after you run badblocks, you should run the SMART Long test again. That will give you a more complete picture of the drive.