Just bought the RocketRaid 644L (Not Rocket 644L), it doesn't work on my freenas 9.3.stable. :-(
I get this first:
Apr 28 22:32:12 freenas ahci0: AHCI v1.00 with 4 6Gbps ports, Port Multiplier supported with FBS
Apr 28 22:32:12 freenas ahcich0: <AHCI channel> at channel 0 on ahci0
Apr 28 22:32:12 freenas ahcich1: <AHCI channel> at channel 1 on ahci0
Apr 28 22:32:12 freenas ahcich2: <AHCI channel> at channel 2 on ahci0
Apr 28 22:32:12 freenas ahcich3: <AHCI channel> at channel 3 on ahci0
Then this:
Apr 28 22:32:12 freenas ahcich0: Timeout on slot 0 port 15
Apr 28 22:32:12 freenas ahcich0: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): CAM status: Command timeout
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): Error 5, Retry was blocked
Apr 28 22:32:12 freenas ahcich1: Timeout on slot 0 port 15
Apr 28 22:32:12 freenas ahcich1: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): CAM status: Command timeout
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): Error 5, Retry was blocked
No disk attached gets recognized.
I then loaded the freebsd kernel driver from highpoint site,
rr64xl-bsd-9.0-1.1.13.529-20130605.tgz, to /boot/kernel,
it reports the card correctly:
ahci0: <HighPoint RocketRAID 644L AHCI SATA controller> port 0xdc00-0xdc07,0xd800-0xd803,0xd400-0xd407,0xd000-0xd003,0xcc00-0xcc1f mem 0xfdfff000-0xfdfff7ff irq 16 at device 0.0 on pci1
ahci0: AHCI v1.00 with 4 6Gbps ports, Port Multiplier supported with FBS
But still the same error:
ahcich0: AHCI reset: device not ready after 31000ms (tfd = 00000080)
ahcich0: Timeout on slot 0 port 15
ahcich0: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
(aprobe0:ahcich0:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
(aprobe0:ahcich0:0:15:0): CAM status: Command timeout
(aprobe0:ahcich0:0:15:0): Error 5, Retry was blocked
run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config
ahcich0: AHCI reset: device not ready after 31000ms (tfd = 00000080)
Anyone else has better luck ?
Thanks
I get this first:
Apr 28 22:32:12 freenas ahci0: AHCI v1.00 with 4 6Gbps ports, Port Multiplier supported with FBS
Apr 28 22:32:12 freenas ahcich0: <AHCI channel> at channel 0 on ahci0
Apr 28 22:32:12 freenas ahcich1: <AHCI channel> at channel 1 on ahci0
Apr 28 22:32:12 freenas ahcich2: <AHCI channel> at channel 2 on ahci0
Apr 28 22:32:12 freenas ahcich3: <AHCI channel> at channel 3 on ahci0
Then this:
Apr 28 22:32:12 freenas ahcich0: Timeout on slot 0 port 15
Apr 28 22:32:12 freenas ahcich0: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): CAM status: Command timeout
Apr 28 22:32:12 freenas (aprobe0:ahcich0:0:15:0): Error 5, Retry was blocked
Apr 28 22:32:12 freenas ahcich1: Timeout on slot 0 port 15
Apr 28 22:32:12 freenas ahcich1: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): CAM status: Command timeout
Apr 28 22:32:12 freenas (aprobe1:ahcich1:0:15:0): Error 5, Retry was blocked
No disk attached gets recognized.
I then loaded the freebsd kernel driver from highpoint site,
rr64xl-bsd-9.0-1.1.13.529-20130605.tgz, to /boot/kernel,
it reports the card correctly:
ahci0: <HighPoint RocketRAID 644L AHCI SATA controller> port 0xdc00-0xdc07,0xd800-0xd803,0xd400-0xd407,0xd000-0xd003,0xcc00-0xcc1f mem 0xfdfff000-0xfdfff7ff irq 16 at device 0.0 on pci1
ahci0: AHCI v1.00 with 4 6Gbps ports, Port Multiplier supported with FBS
But still the same error:
ahcich0: AHCI reset: device not ready after 31000ms (tfd = 00000080)
ahcich0: Timeout on slot 0 port 15
ahcich0: is 00000001 cs 00000000 ss 00000000 rs 00000001 tfd 50 serr 00000000 cmd 00710017
(aprobe0:ahcich0:0:15:0): READ_BUFFER/PM. ACB: e4 00 00 00 00 0f 00 00 00 00 00 00
(aprobe0:ahcich0:0:15:0): CAM status: Command timeout
(aprobe0:ahcich0:0:15:0): Error 5, Retry was blocked
run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config
ahcich0: AHCI reset: device not ready after 31000ms (tfd = 00000080)
Anyone else has better luck ?
Thanks