NUT not working (Solved with little to no input)

[Visseroth]

I'm not real sure where to put this since NUT (UPS) is a service not a plugin but I'm needing to get net to work via SNMP. Currently my configuration is

UPS Mode: Master
Identifier: Tripp2200UPS
Driver: Various ups 3 (various) SNMP - RFC 1628 (snmp-ups)
Port: (UPS address)
Auxiliary parameters: Comunity = ********
snmp_version = v1
mibs = ietf
Pollfreq = 30
Description: TrippLite
Shutdown mode: UPS goes on battery
Shutdown timer: 300
Monitor User: *******
Monitor Password: ********
Remote Monitor: Disabled
Send Email Status Updates: Enabled

I had it working on my firewall via snmp v2 and v1 at one point but a update broke that.
I have not been able to get it to work via snmp on FreeNAS with snmp v1, 2, 2b or anything else for that matter.
Any help would be GREATLY appreciated.

 

[dlavigne]

Which version of FreeNAS? Can you give an example of a failed usage with its error message?

 

[Visseroth]

Forgive me, I did forget to post that information.

FreeNAS-9.3-STABLE-201412090314

The error in the console is.....

Jan 5 14:14:56 storage notifier: Starting nut_upslog.
Jan 5 14:14:56 storage notifier: Warning: initial connect failed: Connection failure: Connection refused
Jan 5 14:14:58 storage notifier: Stopping nut_upslog.
Jan 5 14:14:58 storage notifier: Waiting for PIDS: 16634.
Jan 5 14:14:58 storage notifier: Stopping nut_upsmon.

The error via email is.....

COMMBAD - ups

Obviously it's a communication error but I'm not sure what I'm doing wrong. I've tried everything I can think of. I'm running Spiceworks network monitoring and it even sees the device via snmp.

 

[Visseroth]

bump

 

[SweetAndLow]

Try restarting the driver manually

 

[Visseroth]

Doesn't it restart the driver on reboot and doesn't starting the service restart the necessary resources?
I've had the above configuration for quite some time and if I try and start it now it still doesn't work.
Are there any ports that need to be opened. Anyone else have any ideas?
How would I go about restarting the driver?

 

[Visseroth]

Update:
Come to find out that with the 9.3 update that nut is fixed. Apparently I had the address wrong because I had since changed the ip address of my UPS since the last time I tried to use nut.
UPSC output is as follows....

upsc ups@localhost
battery.charge: 100.00
battery.current: 0.00
battery.temperature: 22.00
battery.voltage: 55.00
device.mfr: Tripp Lite
device.model: SU2200RTXL2U
device.type: ups
driver.name: snmp-ups
driver.parameter.mibs: ietf
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: 10.10.10.210
driver.parameter.snmp_version: v1
driver.version: 2.7.2
driver.version.data: ietf MIB 1.4
driver.version.internal: 0.72
input.current: 0.00
input.frequency: 59.90
input.phases: 1.00
input.realpower: 0.00
input.voltage: 119.00
output.current: 0.00
output.frequency: 59.90
output.phases: 1.00
output.power.nominal: 2200.00
output.realpower: 704.00
output.voltage: 1199.00
ups.firmware: 10
ups.firmware.aux: Tripp Lite 3.0.35 (GAPI 2.0)
ups.load: 32.00

For anyone else that runs across this post at least they'll be able to use the above configuration to configure nut for snmp.
ups.mfr: Tripp Lite
ups.model: SU2200RTXL2U
ups.status: OL
ups.test.result: done and passed
ups.timer.reboot: -1
ups.timer.shutdown: -1