fahadshery
Contributor
- Joined
- Sep 29, 2017
- Messages
- 179
Hi,
I am using a Broadcom LSI SAS33008-IT controller.
I have 11 HGST HUC101818CS4205 disks.
Some of them are showing they were formatted with
Now if I try to format it, it gives the following error:
I plan to pass my LSI controller to TrueNas VM.
I also looked at this magnificent thread and this post.
I was able to format some of the same drives but was unable to format some other drives which are the same brand and capacity.
any pointers would be appreciated.
I am using a Broadcom LSI SAS33008-IT controller.
I have 11 HGST HUC101818CS4205 disks.
Some of them are showing they were formatted with
Formatted with type 2 protection
. See below:Code:
root@truenas[~]# sg_readcap -l /dev/da0 Read Capacity results: Protection: prot_en=1, p_type=1, p_i_exponent=0 [type 2 protection] Logical block provisioning: lbpme=0, lbprz=0 Last LBA=3516328367 (0xd196e9af), Number of logical blocks=3516328368 Logical block length=512 bytes Logical blocks per physical block exponent=3 [so physical block length=4096 bytes] Lowest aligned LBA=0 Hence: Device size: 1800360124416 bytes, 1716957.2 MiB, 1800.36 GB root@truenas[~]# smartctl --xall /dev/da0 smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p11 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HGST Product: HUC101818CS4205 Revision: NE02 Compliance: SPC-4 User Capacity: 1,800,360,124,416 bytes [1.80 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Formatted with type 2 protection 8 bytes of protection information per logical block LU is fully provisioned Rotation Rate: 10520 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000cca02c37591c Serial number: 08GZEMBA Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Dec 22 03:37:16 2021 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 27 C Drive Trip Temperature: 55 C
Now if I try to format it, it gives the following error:
Code:
sg_format --format --size=512 /dev/da1 -v HGST HUC101818CS4205 NE02 peripheral_type: disk [0x0] PROTECT=1 << supports protection information>> Unit serial number: 08GYSP8A LU name: 5000cca02c361eb4 mode sense(10) cdb: [5a 00 01 00 00 00 00 00 fc 00] Mode Sense (block descriptor) data, prior to changes: Number of blocks=3516328368 [0xd196e9b0] Block size=512 [0x200] A FORMAT UNIT will commence in 5 seconds ALL data on /dev/da1 will be DESTROYED Press control-C to abort Format unit cdb: [04 18 00 00 00 00] Format unit: Fixed format, current; Sense key: Data Protect Additional sense: Access denied - no access rights Format unit command: Data protect, type: sense key; write protected media? FORMAT UNIT failed
I plan to pass my LSI controller to TrueNas VM.
I also looked at this magnificent thread and this post.
I was able to format some of the same drives but was unable to format some other drives which are the same brand and capacity.
any pointers would be appreciated.