ghostlobster
Dabbler
- Joined
- Oct 10, 2012
- Messages
- 36
OK...I'm going nuts here. I have a 4x1TB RAID z1 array that was running on a 32 bit 8.2. I built another machine running 64 bit 8.3. On first boot, I auto-imported the ZFS volume, all datasets imported just fine. Like an idiot, however, I did a zpool upgrade, so there's no going back.
Upon a reboot of the box, the volume went away!!!! I rebooted, and there was no volume there. At this point, I said the hell with it and just did a reinstall of FreeNAS 8.3, not an upgrade install, but a regular install. Upon reinstall, I did an auto import again. The raid ID comes up, I select auto import, and it returns an error saying that it could not import the volume. Not too informative, and there are no volumes listed in the GUI, but if I go into a shell, and do a zpool status, I get the following:
pool: RAID
state: ONLINE
status: One or more devices has experienced an error resulting in data corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the entire pool from backup.
see: http://www.sun.com/msg/ZFS-8000-8A
scan: none requested
config:
NAME STATE READ WRITE CKSUM
RAID ONLINE 0 0 1
raidz1-0 ONLINE 0 0 2
gptid/32ea520c-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/35b37ca9-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/36a53dae-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/29ace990-0420-11e2-ba6f-000acd1fbb8d ONLINE 0 0
Now, upon another reboot, the ZFS volume is still gone, and now a zpool status says no pools available. So, tried autoimport again, same issue. Error: could not import ZFS Volume, even though the ZFS volume appears in the auto import field. Now, I'm OK if there was some data corruption on one of the drives, but all 4 of them? I'm not buying that for a minute. I'm using RAID z1 with 4 drives to protect against a single drive failure bringing the system down. Can anyone please help?
Here are the system properties:
Hostname freenas.local
Build FreeNAS-8.3.0-BETA3-x64 (r12468M)
Platform AMD Athlon(tm) 64 X2 Dual Core Processor 4600+
Memory 4080MB
System Time Fri Oct 12 05:37:57 PDT 2012
Uptime 5:37AM up 3 mins, 0 users
Load Average 0.24, 0.34, 0.16
Connected through 192.168.2.179
I know, I should NEVER have upgraded the ZFS volume to 28 before backing things up, my bad. I need the data on this, though. Can anyone point me in some direction here?
Thanks!
***Edit***
A gpart show shows the following:
=> 63 390721905 ada0 MBR (186G)
63 1930257 1 freebsd [active] (942M)
1930320 63 - free - (31k)
1930383 1930257 2 freebsd (942M)
3860640 3024 3 freebsd (1.5M)
3863664 41328 4 freebsd (20M)
3904992 386816976 - free - (184G)
=> 34 1953525101 ada1 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 34 1953525101 ada2 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 0 1930257 ada0s1 BSD (942M)
0 16 - free - (8.0k)
16 1930241 1 !0 (942M)
=> 34 1953525101 ada3 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 34 1953525101 ada4 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
Any ideas?? Basically, the volume does not exist in the GUI. I even tried a zpool import -f RAID, and that returns the following:
cannot import 'RAID': one or more devices is currently unavailable
Upon a reboot of the box, the volume went away!!!! I rebooted, and there was no volume there. At this point, I said the hell with it and just did a reinstall of FreeNAS 8.3, not an upgrade install, but a regular install. Upon reinstall, I did an auto import again. The raid ID comes up, I select auto import, and it returns an error saying that it could not import the volume. Not too informative, and there are no volumes listed in the GUI, but if I go into a shell, and do a zpool status, I get the following:
pool: RAID
state: ONLINE
status: One or more devices has experienced an error resulting in data corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the entire pool from backup.
see: http://www.sun.com/msg/ZFS-8000-8A
scan: none requested
config:
NAME STATE READ WRITE CKSUM
RAID ONLINE 0 0 1
raidz1-0 ONLINE 0 0 2
gptid/32ea520c-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/35b37ca9-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/36a53dae-031e-11e2-b182-000acd1fbb8d ONLINE 0 0 0
gptid/29ace990-0420-11e2-ba6f-000acd1fbb8d ONLINE 0 0
Now, upon another reboot, the ZFS volume is still gone, and now a zpool status says no pools available. So, tried autoimport again, same issue. Error: could not import ZFS Volume, even though the ZFS volume appears in the auto import field. Now, I'm OK if there was some data corruption on one of the drives, but all 4 of them? I'm not buying that for a minute. I'm using RAID z1 with 4 drives to protect against a single drive failure bringing the system down. Can anyone please help?
Here are the system properties:
Hostname freenas.local
Build FreeNAS-8.3.0-BETA3-x64 (r12468M)
Platform AMD Athlon(tm) 64 X2 Dual Core Processor 4600+
Memory 4080MB
System Time Fri Oct 12 05:37:57 PDT 2012
Uptime 5:37AM up 3 mins, 0 users
Load Average 0.24, 0.34, 0.16
Connected through 192.168.2.179
I know, I should NEVER have upgraded the ZFS volume to 28 before backing things up, my bad. I need the data on this, though. Can anyone point me in some direction here?
Thanks!
***Edit***
A gpart show shows the following:
=> 63 390721905 ada0 MBR (186G)
63 1930257 1 freebsd [active] (942M)
1930320 63 - free - (31k)
1930383 1930257 2 freebsd (942M)
3860640 3024 3 freebsd (1.5M)
3863664 41328 4 freebsd (20M)
3904992 386816976 - free - (184G)
=> 34 1953525101 ada1 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 34 1953525101 ada2 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 0 1930257 ada0s1 BSD (942M)
0 16 - free - (8.0k)
16 1930241 1 !0 (942M)
=> 34 1953525101 ada3 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
=> 34 1953525101 ada4 GPT (931G)
34 94 - free - (47k)
128 4194304 1 freebsd-swap (2.0G)
4194432 1949330703 2 freebsd-zfs (929G)
Any ideas?? Basically, the volume does not exist in the GUI. I even tried a zpool import -f RAID, and that returns the following:
cannot import 'RAID': one or more devices is currently unavailable