BulgarianHealer
Dabbler
- Joined
- Jul 16, 2022
- Messages
- 17
Yesterday in another thread(where @Daisuke tried to help me) i posted a problem with formatting IBM 6TB HDD SAS from 4k with TP10 protection(type 2).
The thread: https://www.truenas.com/community/t...warnings-in-bluefin.106051/page-4#post-734528
The problem is:
Output for: openSeaChest_Info -id /dev/sda
The output:
Because my SAS does not support SBC4, @Daisuke gave me this command:
After that @jgreco give an idea to attach the HDD to the controller and open a thread.
Because it's a custom server/chassis is gonna be a mess and time-eater to attach/reattach cable to the LSI Controller. So i have take out the HDD and put it in a new server(Supermicro with the same backplane which is connected to a "newer" LSI card, currently this server was just going online so i can play with the HDD). I tried to perform the same commands, but the error its still the same as in the other forum thread.
The thread: https://www.truenas.com/community/t...warnings-in-bluefin.106051/page-4#post-734528
The problem is:
Code:
root@truenas[~]# time sg_format -vFf 0 -s 512 /dev/sda
IBM-D050 ST6000NM0014 BC7B peripheral_type: disk [0x0]
PROTECT=1
<< supports protection information>>
Unit serial number: S4D090ZD0000K601HQC0
LU name: 5000c5008e58e757
mode sense(10) cdb: [5a 00 01 00 00 00 00 00 fc 00]
Mode Sense (block descriptor) data, prior to changes:
number of blocks will max out, set <<longlba>>
mode sense(10) cdb: [5a 10 01 00 00 00 00 00 fc 00]
<<< longlba flag set (64 bit lba) >>>
Number of blocks=1465130646 [0x57541e96]
Block size=4096 [0x1000]
mode select(10) cdb: [55 11 00 00 00 00 00 00 24 00]
mode select(10):
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in parameter list
Field replaceable unit code: 17
Sense Key Specific: Error in Data parameters: byte 21 bit 7
Try MODE SELECT again with SP=0 this time
mode select(10) cdb: [55 10 00 00 00 00 00 00 24 00]
mode select(10):
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in parameter list
Field replaceable unit code: 17
Sense Key Specific: Error in Data parameters: byte 21 bit 7
MODE SELECT command: Illegal request, type: sense key, apart from Invalid opcode
sg_format -vFf 0 -s 512 /dev/sda 0.00s user 0.00s system 1% cpu 0.139 total
Output for: openSeaChest_Info -id /dev/sda
The output:
Code:
root@truenas[~]# openSeaChest_Info -id /dev/sda
==========================================================================================
openSeaChest_Info - openSeaChest drive utilities - NVMe Enabled
Copyright (c) 2014-2022 Seagate Technology LLC and/or its Affiliates, All Rights Reserved
openSeaChest_Info Version: 2.0.0-2_2_1 X86_64
Build Date: Dec 13 2022
Today: Thu Jan 5 00:38:31 2023 User: root
==========================================================================================
/dev/sg2 - ST6000NM0014 - S4D090ZD0000K601HQC0 - SCSI
Vendor ID: IBM-D050
Model Number: ST6000NM0014
Serial Number: S4D090ZD0000K601HQC0
Firmware Revision: BC7B
World Wide Name: 5000C5008E58E757
Drive Capacity (TB/TiB): 6.00/5.46
Temperature Data:
Current Temperature (C): 37
Highest Temperature (C): Not Reported
Lowest Temperature (C): Not Reported
Power On Time: 5 years 19 days 8 hours 36 minutes
Power On Hours: 44264.60
MaxLBA: 1465130645
Native MaxLBA: Not Reported
Logical Sector Size (B): 4096
Physical Sector Size (B): 4096
Sector Alignment: 0
Rotation Rate (RPM): 7200
Form Factor: 3.5"
Last DST information:
Time since last DST (hours): 0.60
DST Status/Result: 0x0
DST Test run: 0x1
Long Drive Self Test Time: 10 hours 43 minutes
Interface speed:
Port 0 (Current Port)
Max Speed (GB/s): 12.0
Negotiated Speed (Gb/s): 6.0
Port 1
Max Speed (GB/s): 12.0
Negotiated Speed (Gb/s): Not Reported
Annualized Workload Rate (TB/yr): 82.63
Total Bytes Read (TB): 311.36
Total Bytes Written (TB): 106.15
Encryption Support: Not Supported
Cache Size (MiB): Not Reported
Read Look-Ahead: Not Supported
Write Cache: Disabled
SMART Status: Good
ATA Security Information: Not Supported
Firmware Download Support: Full, Segmented, Deferred
Number of Logical Units: 1
Specifications Supported:
SPC-4
SAM-5
SAS-3
SPL-3
SPC-4
SBC-3
Features Supported:
Protection Type 1
Protection Type 2 [Enabled]
Application Client Logging
Self Test
Automatic Write Reassignment [Enabled]
Automatic Read Reassignment [Enabled]
EPC
Informational Exceptions [Mode 4]
Translate Address
Format Unit
Sanitize
Adapter Information:
Vendor ID: 1000h
Product ID: 0087h
Revision: 0005h
Because my SAS does not support SBC4, @Daisuke gave me this command:
Code:
root@truenas[~]# openSeaChest_FormatUnit -d /dev/sda --stopOnListError --protectionType 0 --formatUnit 512 --poll --confirm this-will-erase-data ========================================================================================== openSeaChest_Format - openSeaChest drive utilities - NVMe Enabled Copyright (c) 2014-2022 Seagate Technology LLC and/or its Affiliates, All Rights Reserved openSeaChest_Format Version: 2.2.1-2_2_1 X86_64 Build Date: Dec 13 2022 Today: Thu Jan 5 01:22:34 2023 User: root ========================================================================================== /dev/sg2 - ST6000NM0014 - S4D090ZD0000K601HQC0 - SCSI Format Unit Format Unit Failed!
After that @jgreco give an idea to attach the HDD to the controller and open a thread.
Because it's a custom server/chassis is gonna be a mess and time-eater to attach/reattach cable to the LSI Controller. So i have take out the HDD and put it in a new server(Supermicro with the same backplane which is connected to a "newer" LSI card, currently this server was just going online so i can play with the HDD). I tried to perform the same commands, but the error its still the same as in the other forum thread.
