Hi -
Put in a 2 port 1g nic card
Tried to link aggregate it using round robin...
I can ping myself ok, but anything else gets 'network Down'
I also tried the same without aggregation, just picking one of the ports, I get nothing, no pings in our out
ifconfig shows:
Where can I start to debug this?
Put in a 2 port 1g nic card
Code:
em0: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xd880-0xd89f mem 0xfbd80000-0xfbd9ffff,0xfbd60000-0xfbd7ffff irq 24 at device 0.0 on pci10 em0: Using an MSI interrupt em0: Ethernet address: 00:15:17:96:6f:c8 em1: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xdc00-0xdc1f mem 0xfbde0000-0xfbdfffff,0xfbdc0000-0xfbddffff irq 34 at device 0.1 on pci10 em1: Using an MSI interrupt em1: Ethernet address: 00:15:17:96:6f:c9
Tried to link aggregate it using round robin...
Code:
em1: link state changed to UP em1: link state changed to DOWN em1: link state changed to UP em0: link state changed to UP arp: 00:15:17:96:6f:c8 is using my IP address 10.10.1.49 on em1! arp: 00:15:17:96:6f:c9 is using my IP address 10.10.1.49 on em0! lagg0: link state changed to UP em1: link state changed to DOWN em1: link state changed to UP
I can ping myself ok, but anything else gets 'network Down'
Code:
[root@freenas] ~# ping 10.10.1.49 PING 10.10.1.49 (10.10.1.49): 56 data bytes 64 bytes from 10.10.1.49: icmp_seq=0 ttl=64 time=0.023 ms 64 bytes from 10.10.1.49: icmp_seq=1 ttl=64 time=0.025 ms ^C --- 10.10.1.49 ping statistics --- 2 packets transmitted, 2 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 0.023/0.024/0.025/0.001 ms [root@freenas] ~# ping 10.10.1.180 PING 10.10.1.180 (10.10.1.180): 56 data bytes ping: sendto: Network is down ping: sendto: Network is down ^C --- 10.10.1.180 ping statistics --- 2 packets transmitted, 0 packets received, 100.0% packet loss
I also tried the same without aggregation, just picking one of the ports, I get nothing, no pings in our out
ifconfig shows:
Code:
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=4019b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,VLAN_HWTSO> ether 00:15:17:96:6f:c8 inet 10.10.1.49 netmask 0xffffff00 broadcast 10.10.1.255 nd6 options=9<PERFORMNUD,IFDISABLED> media: Ethernet autoselect (1000baseT <full-duplex>) status: active em1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=4019b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,VLAN_HWTSO> ether 00:15:17:96:6f:c8 inet 10.10.1.49 netmask 0xffffff00 broadcast 10.10.1.255 nd6 options=9<PERFORMNUD,IFDISABLED> media: Ethernet autoselect (1000baseT <full-duplex>) status: active lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=4019b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,VLAN_HWTSO> ether 00:15:17:96:6f:c8 nd6 options=9<PERFORMNUD,IFDISABLED> media: Ethernet autoselect status: active laggproto roundrobin lagghash l2,l3,l4 laggport: em0 flags=4<ACTIVE> laggport: em1 flags=4<ACTIVE>
Where can I start to debug this?