Baenwort
Explorer
- Joined
- Feb 19, 2015
- Messages
- 93
So first I got:
So I then ran a smartctl test and got the following results:
is it the drive or do I need to talk my family through swapping the SATA cable first?
Code:
Oct. 29, 2018, 2:04 p.m. - Device: /dev/da2 [SAT], Self-Test Log error count increased from 2 to 3
So I then ran a smartctl test and got the following results:
Code:
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Extended self-test routine immediately in off-line mode". Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 709 minutes for test to complete. Test will complete after Tue Oct 30 11:00:06 2018 Use smartctl -X to abort test. root@thing:~ # smartctl -A /dev/da2 smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 199 051 Pre-fail Always - 15 3 Spin_Up_Time 0x0027 232 201 021 Pre-fail Always - 7383 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 106 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 32903 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 101 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 55 193 Load_Cycle_Count 0x0032 191 191 000 Old_age Always - 28663 194 Temperature_Celsius 0x0022 120 110 000 Old_age Always - 32 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 224
Code:
root@thing:~ # smartctl -x /dev/da2 smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68MYMN1 Serial Number: WD-WX21D84PDDT3 LU WWN Device Id: 5 0014ee 20b09eae1 Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Oct 30 17:52:19 2018 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 113) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 5564) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 709) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 199 051 - 15 3 Spin_Up_Time POS--K 232 201 021 - 7383 4 Start_Stop_Count -O--CK 100 100 000 - 106 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 055 055 000 - 32904 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 101 192 Power-Off_Retract_Count -O--CK 200 200 000 - 55 193 Load_Cycle_Count -O--CK 191 191 000 - 28666 194 Temperature_Celsius -O---K 121 110 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 224 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 33 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 33 [8] occurred at disk power-on lifetime: 32894 hours (1370 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b1 56 99 a8 40 00 Error: UNC at LBA = 0x1b15699a8 = 7270209960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 01 b1 56 91 a8 40 00 43d+13:31:16.977 READ FPDMA QUEUED 60 01 00 00 38 00 01 b1 56 90 a8 40 00 43d+13:31:16.925 READ FPDMA QUEUED 60 01 00 00 30 00 01 b1 56 8f a8 40 00 43d+13:31:16.925 READ FPDMA QUEUED 60 01 00 00 28 00 01 b1 56 8e a8 40 00 43d+13:31:16.925 READ FPDMA QUEUED 60 01 00 00 20 00 01 b1 56 8d a8 40 00 43d+13:31:16.925 READ FPDMA QUEUED Error 32 [7] occurred at disk power-on lifetime: 32894 hours (1370 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 9a 2d 90 40 00 Error: UNC at LBA = 0x1b09a2d90 = 7257861520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 01 b0 9a 34 78 40 00 43d+13:30:54.457 READ FPDMA QUEUED 60 01 00 00 30 00 01 b0 9a 33 78 40 00 43d+13:30:54.456 READ FPDMA QUEUED 60 01 00 00 28 00 01 b0 9a 32 78 40 00 43d+13:30:54.456 READ FPDMA QUEUED 60 01 00 00 20 00 01 b0 9a 31 78 40 00 43d+13:30:54.456 READ FPDMA QUEUED 60 01 00 00 18 00 01 b0 9a 30 78 40 00 43d+13:30:54.456 READ FPDMA QUEUED Error 31 [6] occurred at disk power-on lifetime: 32894 hours (1370 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 98 4f 30 40 00 Error: UNC at LBA = 0x1b0984f30 = 7257739056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 01 b0 98 55 c0 40 00 43d+13:30:44.919 READ FPDMA QUEUED 60 01 00 00 30 00 01 b0 98 54 c0 40 00 43d+13:30:44.919 READ FPDMA QUEUED 60 01 00 00 28 00 01 b0 98 53 c0 40 00 43d+13:30:44.919 READ FPDMA QUEUED 60 01 00 00 20 00 01 b0 98 52 c0 40 00 43d+13:30:44.919 READ FPDMA QUEUED 60 01 00 00 18 00 01 b0 98 51 c0 40 00 43d+13:30:44.919 READ FPDMA QUEUED Error 30 [5] occurred at disk power-on lifetime: 32894 hours (1370 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 96 66 98 40 00 Error: UNC at LBA = 0x1b0966698 = 7257613976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 01 b0 96 6d 98 40 00 43d+13:30:38.249 READ FPDMA QUEUED 60 01 00 00 30 00 01 b0 96 6c 98 40 00 43d+13:30:38.249 READ FPDMA QUEUED 60 01 00 00 28 00 01 b0 96 6b 98 40 00 43d+13:30:38.249 READ FPDMA QUEUED 60 01 00 00 20 00 01 b0 96 6a 98 40 00 43d+13:30:38.249 READ FPDMA QUEUED 60 01 00 00 18 00 01 b0 96 69 98 40 00 43d+13:30:38.249 READ FPDMA QUEUED Error 29 [4] occurred at disk power-on lifetime: 32842 hours (1368 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 9a 42 50 40 00 Error: UNC at LBA = 0x1b09a4250 = 7257866832 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 90 00 02 ba a0 f2 90 40 00 41d+09:24:50.900 READ FPDMA QUEUED 60 00 10 00 88 00 02 ba a0 f0 90 40 00 41d+09:24:50.900 READ FPDMA QUEUED 60 00 10 00 80 00 00 00 40 02 90 40 00 41d+09:24:50.900 READ FPDMA QUEUED 60 01 00 00 78 00 01 b0 9a 54 10 40 00 41d+09:24:50.900 READ FPDMA QUEUED 60 01 00 00 38 00 01 b0 9a 53 10 40 00 41d+09:24:50.900 READ FPDMA QUEUED Error 28 [3] occurred at disk power-on lifetime: 32842 hours (1368 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 9a 38 88 40 00 Error: UNC at LBA = 0x1b09a3888 = 7257864328 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 78 00 01 b0 9a 48 a0 40 00 41d+09:24:42.564 READ FPDMA QUEUED 60 01 00 00 70 00 01 b0 9a 47 a0 40 00 41d+09:24:42.564 READ FPDMA QUEUED 60 01 00 00 68 00 01 b0 9a 46 a0 40 00 41d+09:24:42.564 READ FPDMA QUEUED 60 01 00 00 60 00 01 b0 9a 45 a0 40 00 41d+09:24:42.564 READ FPDMA QUEUED 60 01 00 00 58 00 01 b0 9a 44 a0 40 00 41d+09:24:42.564 READ FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 32842 hours (1368 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 99 88 28 40 00 Error: UNC at LBA = 0x1b0998828 = 7257819176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 01 b0 99 8e 78 40 00 41d+09:24:35.313 READ FPDMA QUEUED 60 01 00 00 30 00 01 b0 99 8d 78 40 00 41d+09:24:35.313 READ FPDMA QUEUED 60 01 00 00 28 00 01 b0 99 8c 78 40 00 41d+09:24:35.313 READ FPDMA QUEUED 60 01 00 00 20 00 01 b0 99 8b 78 40 00 41d+09:24:35.313 READ FPDMA QUEUED 60 01 00 00 18 00 01 b0 99 8a 78 40 00 41d+09:24:35.313 READ FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 32842 hours (1368 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 b0 99 7d a8 40 00 Error: UNC at LBA = 0x1b0997da8 = 7257816488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 68 00 01 b0 99 84 78 40 00 41d+09:24:28.322 READ FPDMA QUEUED 60 01 00 00 08 00 01 b0 99 83 78 40 00 41d+09:24:28.322 READ FPDMA QUEUED 60 01 00 00 60 00 01 b0 99 82 78 40 00 41d+09:24:28.311 READ FPDMA QUEUED 60 01 00 00 58 00 01 b0 99 81 78 40 00 41d+09:24:28.311 READ FPDMA QUEUED 60 01 00 00 50 00 01 b0 99 80 78 40 00 41d+09:24:28.311 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 10% 32904 7257864096 # 2 Extended offline Completed: read failure 40% 32893 7257613976 # 3 Conveyance offline Completed without error 00% 32886 - # 4 Short offline Completed: read failure 10% 32885 7257861504 # 5 Short offline Completed: read failure 10% 32880 7257859088 # 6 Extended offline Completed: read failure 40% 32876 7204548288 # 7 Short offline Completed without error 00% 32856 - # 8 Short offline Completed without error 00% 32832 - # 9 Short offline Completed without error 00% 32808 - #10 Short offline Completed without error 00% 32784 - #11 Short offline Completed without error 00% 32760 - #12 Short offline Completed without error 00% 32736 - #13 Short offline Completed without error 00% 32712 - #14 Extended offline Completed: read failure 40% 32709 7204535024 #15 Short offline Completed without error 00% 32688 - #16 Short offline Completed without error 00% 32664 - #17 Short offline Completed without error 00% 32640 - #18 Short offline Completed without error 00% 32616 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 28/41 Celsius Lifetime Min/Max Temperature: 2/42 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (92) Index Estimated Time Temperature Celsius 93 2018-10-30 09:55 32 ************* ... ..( 14 skipped). .. ************* 108 2018-10-30 10:10 32 ************* 109 2018-10-30 10:11 31 ************ ... ..( 6 skipped). .. ************ 116 2018-10-30 10:18 31 ************ 117 2018-10-30 10:19 32 ************* ... ..( 21 skipped). .. ************* 139 2018-10-30 10:41 32 ************* 140 2018-10-30 10:42 31 ************ ... ..( 17 skipped). .. ************ 158 2018-10-30 11:00 31 ************ 159 2018-10-30 11:01 33 ************** ... ..( 18 skipped). .. ************** 178 2018-10-30 11:20 33 ************** 179 2018-10-30 11:21 34 *************** ... ..( 9 skipped). .. *************** 189 2018-10-30 11:31 34 *************** 190 2018-10-30 11:32 33 ************** ... ..( 6 skipped). .. ************** 197 2018-10-30 11:39 33 ************** 198 2018-10-30 11:40 32 ************* ... ..( 7 skipped). .. ************* 206 2018-10-30 11:48 32 ************* 207 2018-10-30 11:49 31 ************ ... ..( 16 skipped). .. ************ 224 2018-10-30 12:06 31 ************ 225 2018-10-30 12:07 32 ************* ... ..( 11 skipped). .. ************* 237 2018-10-30 12:19 32 ************* 238 2018-10-30 12:20 33 ************** ... ..( 25 skipped). .. ************** 264 2018-10-30 12:46 33 ************** 265 2018-10-30 12:47 32 ************* ... ..( 13 skipped). .. ************* 279 2018-10-30 13:01 32 ************* 280 2018-10-30 13:02 33 ************** ... ..( 42 skipped). .. ************** 323 2018-10-30 13:45 33 ************** 324 2018-10-30 13:46 32 ************* ... ..( 10 skipped). .. ************* 335 2018-10-30 13:57 32 ************* 336 2018-10-30 13:58 33 ************** ... ..( 7 skipped). .. ************** 344 2018-10-30 14:06 33 ************** 345 2018-10-30 14:07 34 *************** 346 2018-10-30 14:08 33 ************** ... ..( 28 skipped). .. ************** 375 2018-10-30 14:37 33 ************** 376 2018-10-30 14:38 32 ************* ... ..( 5 skipped). .. ************* 382 2018-10-30 14:44 32 ************* 383 2018-10-30 14:45 33 ************** ... ..( 27 skipped). .. ************** 411 2018-10-30 15:13 33 ************** 412 2018-10-30 15:14 34 *************** ... ..( 68 skipped). .. *************** 3 2018-10-30 16:23 34 *************** 4 2018-10-30 16:24 33 ************** ... ..( 24 skipped). .. ************** 29 2018-10-30 16:49 33 ************** 30 2018-10-30 16:50 32 ************* ... ..( 4 skipped). .. ************* 35 2018-10-30 16:55 32 ************* 36 2018-10-30 16:56 33 ************** ... ..( 52 skipped). .. ************** 89 2018-10-30 17:49 33 ************** 90 2018-10-30 17:50 32 ************* 91 2018-10-30 17:51 32 ************* 92 2018-10-30 17:52 32 ************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 22 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 136 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 8097004 Vendor specific
is it the drive or do I need to talk my family through swapping the SATA cable first?
